新型微光探测器激光防护材料的研究

系统分析了微光夜视器的结构及其原理，并结合当前器件存在的激光致盲威胁，提出了增强系统安全的新措施。同时，系统地介绍了防激光滤光材料一些重要的性能参数以及滤光材料的组成、制备加工工艺。研究结果表明，新型的防激光材料能够有效地防护800nm，900nm以及10613nm等三个波长的激光，并且可见光透过率大于85％。     

Non-equilibrium particle motion in the vicinity of a single blade

The motion of sand particles close to a single moving blade was investigated using Positron Emission Particle Tracking (PEPT) during the period in which the free bed surface profile was evolving to an equilibrium shape. The area affected by the blade was divided into active and inactive regions and these were analysed separately. The characteristic heart-shape of the active region in the plan view was determined. An approximately 10-particle-diameter wide velocity transition zone is found between the two regions. While the tracer particle is in the inactive region moving away from the blade, the time dependence of the axial displacement is well described by a logarithmic relationship. The probability of particle movement towards the centre of the blade was quantified using a “central tendency” index. The calculated central tendency shows maxima at each side of the blade. The separation of the two maxima, which indicates the width of the active region, increases with fill level but is independent of rotational speed.     

光学材料的激光微加工研究进展与应用前景

综述了国内外在光学材料激光微加工方面的研究成果和应用状况，并展望了其发展前景。     

声诱饵仿真试验系统

介绍了声诱饵仿真试验系统的组成、工作原理、对接装置结构等,建立了对接装置声耦合状态下的数学模型,对近场声压分布进行了仿真计算,得出了匹配材料厚度、发射和接收换能器的选取原则。     

Investigation into polishing process of CVD diamond films

A new technique used for polishing chemical vapor deposition (CVD) diamond films has been investigated, by which rough polishing of the CVD diamond films can be achieved efficiently. A CVD diamond film is coated with a thin layer of electrically conductive material in advance, and then electro-discharge machining (EDM) is used to machine the coated surface. As a result, peaks on the surface of the diamond film are removed rapidly. During machining, graphitization of diamond enables the EDM process to continue. The single pulse discharge shows that the material of the coated layer evidently affects removal behavior of the CVD diamond films. Compared with the machining of ordinary metal materials, the process of EDM CVD diamond films possesses a quite different characteristic. The removal mechanism of the CVD diamond films is discussed.     

正确选用热力管网保温材料的几个问题

介绍了做好热力管网保温应具备的有关知识和数据，以及宝钢蒸汽主干管网在采用四种保温材料下的经济保温层厚度和相对的节能效益，认为目前适于宝钢公司热源温度在６００℃以下较好的保温材料有新型矿渣棉制品和泡沫石棉板。     

荧光显示管直丝氧化物阴极有效逸出功的计算

阴极的逸出功是表征阴极发射能力的物理量，求定荧光显示管直丝氧化物阴极有效逸出功时，因其零场发射电流密度难于准确取值，温度无法直接测量，显得困难，须予解决，为此提出了一种计算阴极有产逸出功的办法，对某显示管的发射欠佳和“低温高效”的两种氧化物阴极的有效逸出功进行计算，有效逸出功率是靠测量相关物理量再同计算得出，精度不很高，文中所用办法也不例外，但所得结果能反映阴极发射能力，所需仪器少，是实用方法。     

点阴极电场辅助阳极连接中的紧密接触面积和电流

用等效电路的方法研究了点阴极情况下的电场辅助阳极连接效应，计算了连接电流，连接孕育期和紧密接触面积，本文结果表明，连接初期电流迅速衰减，随后缓慢变小，直至某一稳定值，孕育期随温度上升指数下降，连接温度高时，孕育期将难以观察到；待连接表面之间紧密接触面积随时间延长而非线性扩展，紧密接触区域增大时，其边界向外推进速度渐小，而接触面积增加渐快。     

湿硫化氢环境下的球罐腐蚀状况分析

在湿硫化氢环境下 ,尤其储存介质中的硫化氢含量超标时 ,很容易对储存容器壳体 (含焊缝和母材 )造成硫化氢应力腐蚀或氢鼓包。作者较仔细分析了 1 0 0 0m3 丙烯球罐产生硫化氢应力腐蚀开裂和40 0m3 LPG球罐产生氢鼓包的原因。提出了此类设备在设计选材、设备制造、施工安装和使用维护等环节应注意的问题。     

天然多糖类/蛋白质复合材料的研究进展

在参考了 31篇文献的基础上 ,详述了天然多糖类与蛋白质复合材料的研究进展