放射性核素迁移的实验室研究——Ⅱ.用混合裂变产物溶液研究核素在地质材料上的吸附

应用裂变产物混合物做为示踪剂研究了~(137)Cs,~(141,144)Ce,~(103,106)Ru,~(103,106)Ru,~(95)Zr,~(95)Nb,~(89,90)Sr在花岗岩、凝灰岩、页岩上的吸附行为。应用批式技术测定了吸附比。核素的γ放射性是用连有SCORPIO-3000多道计算机系统的Ce(Li)探测器测量的。β放射性~(89,90)Sr是放化分离后在G-M计数器上测量的。结果表明:凝灰岩、页岩能强烈吸附Ce,Nb,Zr;吸附Cs居中;吸附Sr,Ru较差;花岗岩的吸附性能都差。     

Solubility of amaranth seed proteins in sodium sulphate and sodium chloride: the main factor in quantitative extraction for analysis

Nitrogen was extracted more efficiently from amaranth seed with 0.04 M Na₂SO₄ (5% w/v) than with either 0.09 M or 0.17 M NaCl (5% or 10% w/v), despite both solutions having the same ionic strength (μ= 1). Solubility of saline soluble proteins (albumin ± globulin) was very poor in either water or 1M NaCl, but increased in 0.4M NaCl at alkaline pH between 7 and 10. Globulins were very soluble in 0.4M NaCl at a pH 9. Albumin was the main storage protein. Saline soluble proteins formed very weak gels.     

Preparation and properties of silicone‐containing poly(methyl methacrylate) gels

Poly(methyl methacrylate) (PMMA) gels with varying amounts of silicone and solvent and constant amounts of crosslinker were prepared by solution free radical crosslinking copolymerization of methyl methacrylate (MMA), ethylene glycol dimethacrylate (EGDM), tetraethoxysilane (TEOS) and vinyltriethoxysilane (VTES) comonomer systems. They were then studied in benzene at a total monomer concentration of 3.5 mol L^?1 and 70 °C. The conversion of monomer, volume swelling ratio, weight fraction and gel point were measured as a function of the reaction time, silicone concentration and benzene content up to the onset of macrogelation. Structural characteristics of the gels were examined by using equilibrium swelling in benzene, gel fraction and Fourier‐transform infrared (FTIR) analysis. The morphology of the copolymers was also investigated by SEM. Based on the obtained results, it was concluded that the FTIR data did not have the capacity to show the presence of the VTES or TEOS moiety in these kinds of copolymers. On the other hand, the variation of weight fraction of gel, W_g, and its equilibrium volume swelling ratio in benzene, q_v, exhibited the same behaviour as that of MMA/EGDM copolymers. Also, the dilution of the monomer mixture resulted in an increase in the gel point and swelling degree and a decrease in the percent of conversion and gel fraction. Finally, TEOS is not an ideal silicone compound for reaction in the MMA/EGDM copolymerization system, whereas VTES is a suitable silicone comonomer for this system and it has been proved useful. Copyright © 2005 Society of Chemical Industry     

钢纤维聚合物混凝土抗压本构关系

钢纤维聚合物混凝土是由聚合物混凝土基体和钢纤维共同组成的纤维增强复合材料，它的力学行为不仅依赖于聚合物混凝土基体的行为，而且与钢纤维的掺量、分散特征以及钢纤维的几何尺寸有关，本文将基于损伤力学原理研究在不同纤维掺量下的钢纤维聚合物混凝土的全程压力-应变曲线及其本构模型。     

Effect of plate aspect ratio on the recovery of deuterium from water-isotope mixture in flat-plate thermal diffusion columns with transverse sampling streams

The optimal plate aspect ratios for the best recovery of deuterium from water-isotope mixture in flat-plate thermal diffusion columns with transverse sampling streams have been determined. The maximum recovery and maximum production rate are achieved without changing the total expenditure, while the design with minimum plate surface area results in minimizing the total expense.     

Heat loss and thermoelectric generator design

With the object of evaluating its importance to thermoelectric generator design, heat loss is introduced into the standard thermoelectric generator design theory. The theory for both the constant hot and cold junction temperatures model and the constant heat input model are so modified. The modification is first order and, therefore, is limited to small leg heat-transfer coefficients. Numerical results using representative properties show that significant differences can exist between the optimum geometry and performance of a generator idealized as lossless and those of a generator designed by the modified theory. The largest differences occur with the constant heat input model.     

未知钍—铀比的误差分析

研究了在任意Th、U含量和Th-U比覆盖整个范围(即0≤Th/U≤∝)时总α计数率对年剂量的转换因子及其误差。结果表明,当不测定Th-U比而只测量总α计数率时,最终引起的年龄误差对0≤Th/U≤∝来说为±5.1％-±8.3％,对1.1≤Th/U≤9.5来说只有±2.5％％-±4.1％。     

Investigation of fusion reactions in palladium and titanium tritide using galvanostatic,coulometric, and hydrogen permeation techniques

We describe several electrochemical methods used to investigate the possibility of cold fusion phenomena in palladium and titanium tritide cathodes. We performed long-term (up to 77 days) electrolysis experiments with electrochemical cells of the University of Utah type at current densities as high as 1 A/cm², while monitoring neutron and tritium levels. With some cells, we pulsed the current to determine if neutron bursts would result. In another cell, we used titanium tritide as the cathode to determine if D-T reactions yielding neutrons would occur. In no instance were levels of neutrons or tritium significantly above background except in the titanium tritide cell where isotopic exchange, occcurring between the electrode and the electrolyte, resulted in significant tritium levels. We also combined x-ray photoelectron spectroscopy (XPS) and electrochemical hydrogen permeation experiments to determine the effectiveness of various Pd surface treatment procedures on the resultant electrochemical hydrogen absorption efficiency. Electroanalytical and thermal desorption/gas analysis techniques indicated the maximum loading of H in Pd was to a ratio of HPd=0.8.     

Study on Surface Engineering of Normalized Steels Subjected To Machine

Engineering the surfaces of components to improve the life and performance of parts used in automotive and aerospace engineering is the active area of research. Suitable Thermal/Mechanical/Thermo mechanical surface engineering treatments will produce extensive rearrangement of atoms in metals and alloys and corresponding marked variations in Physical, Chemical and Mechanical properties. Among the more important of these treatments are heat treatment processes such as hardening by Quenching, Induction hardening and Case Carburizing which rely on phase transformations to produce desired changes in mechanical properties. Other processes where phase transformation occur are casting, welding and machining etc. [1] Phase transformation may be homogeneous or heterogeneous. Homogeneous involves rearrangements in the structure of the material taking place simultaneously in all parts of the solid, while the heterogeneous transformation involves structural changes which are more localized. Alternatively they could be called as Isothermal and Nonisothermal transformation. But irrespective of the classification, these transformations alter the structure of the material giving rise to changes in the mechanical and physical properties of the processed material. It is of interest to review some consequences of surface modification in isothermal (Normalizing) and nonisothermal transformations (Machining) of low carbon steels.