Synthesis and Evaluation of Blends Formed by Polymeric Crown Ethers and a Fullerene-Containing Primary Ammonium Salt in Organic Thin Films

The synthesis of a series of polymers and cyclopolymers bearing crown ethers of differing structure and affinities towards primary ammonium ions is discussed. These polymers have been tested in their efficiency to form structurally homogeneous thin films when blended with an amphiphilic C₆₀ compound containing a primary ammonium ion functional group. The X-ray reflectivity characterization of the films revealed that the polymer bearing the crown ether with the least affinity for primary ammonium ions, but having the highest degree of polymerization, is the most effective in forming structurally homogeneous thin films.     

Extensions of LDA by PCA mixture model and class-wise features

Linear discriminant analysis (LDA) is a data discrimination technique that seeks transformation to maximize the ratio of the between-class scatter and the within-class scatter. While it has been successfully applied to several applications, it has two limitations, both concerning the underfitting problem. First, it fails to discriminate data with complex distributions since all data in each class are assumed to be distributed in the Gaussian manner. Second, it can lose class-wise information, since it produces only one transformation over the entire range of classes. We propose three extensions of LDA to overcome the above problems. The first extension overcomes the first problem by modelling the within-class scatter using a PCA mixture model that can represent more complex distribution. The second extension overcomes the second problem by taking different transformation for each class in order to provide class-wise features. The third extension combines these two modifications by representing each class in terms of the PCA mixture model and taking different transformation for each mixture component. It is shown that all our proposed extensions of LDA outperform LDA concerning classification errors for synthetic data classification, hand-written digit recognition, and alphabet recognition.     

彩色半柔性混合料路用性能研究

彩色半柔性混合料是一种在开级配沥青混合料中填充水泥胶浆而形成的兼具沥青路面与水泥混凝土路面优点的彩色复合路面。利用车辙试验来评价彩色半柔性混合料的高温稳定性,用残留稳定度和冻融劈裂试验评价半柔性混合料的水稳定性。结果表明,半柔性混合料具有优良的高温稳定性和疲劳性能,水稳定性较好。     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry     

离子束混合工艺对材料抗蚀性能的影响

本文介绍了离子束混合工艺方法。与直接注入相比较,离子束混合所使用的设备造价低1/4—1/2,而生产效率可提高1—2个数量级,因而使生产成本大幅度降低,这无疑对离子束工艺的实际应用将产生巨大的促进作用。 通过对轴承材料(GCr15和Cr4Mo4V)经Cr、N、Ta不同元素的混合处理后,在0.5M H_2SO_4和0.1M NaCl的缓冲溶液中的阳极极化曲线表明经混合处理后的两种材料试样,其抗蚀能力和抗点蚀能力均大大提高,这与直接注入的试样效果是一致的。 通过俄歇谱仪和透射电镜的分析结果表明混合是成功的,且在一定的条件下,形成非晶组织。 本文的结论是,无论是离子的直接注入还是离子束混合,对提高轴承材料的抗腐蚀性能都是有效的方法,特别是离子束混合技术具有更大的应用前景。     

涂层材料的断裂分析(英文)

和基体厚度相比,涂层很薄,因此细观力学模型可把基体作为半无限弹性体。由于涂层和基体材料的膨胀系数及弹性系数不匹配,涂层材料中残余热应力的解析解为 E_c/(1-γ_c)·(α_s-α_c)△T。用有限元法校核,该应力和解析解吻合得好。通过对涂层产生裂纹驱动力和断裂韧性的讨论,提出了抗裂涂层厚度公式。     

Prediction of evaporation heat transfer coefficient and pressure drop of refrigerant mixtures

A study on the prediction of heat transfer coefficient (HTC) and pressure drop of refrigerant mixtures is reported. HTCs and pressure drops of prospective mixtures to replace R12 and R22 are predicted on the same cooling capacity basis. Results indicate that nucleate boiling is suppressed at qualities greater than 20.0% for all mixtures and evaporation becomes the main heat transfer mechanism. For the same capacity, some mixtures containing R32 and R152a show 8.0–10.0% increase in HTCs. Some mixtures with large volatility difference exhibit as much as 55.0% reduction compared with R12 and R22, caused by mass transfer resistance and property degradation due to mixing (32.0%) and reduced mass flow rates (23.0%). Other mixtures with moderate volatility difference exhibit 20.0–30.0% degradation due mainly to reduced mass flow rates. The overall impact of heat transfer degradation, however, is insignificant if major heat transfer resistance exists in the heat transfer fluid side (air system). If the resistance in the heat transfer fluid side is of the same order of magnitude as that on the refrigerant side (water system), considerable reduction in overall HTC of up to 20% is expected. A study of the effect of uncertainties in transport properties on heat transfer shows that transport properties of liquid affect heat transfer more than other properties. Uncertainty of 10.0% in transport properties causes a change of less than 6% in heat transfer prediction.     

化学镀SiCp／Ni－P复合镀层与基体结合强度及其影响因素

论述了ＳｉＣｐ／Ｎｉ－Ｐ复合镀层与钢基体的结合强度及其影响因素。复合镀层中离界面５μｍ厚度以内区域的组成及应力状态对镀层／基体的界面结合有决定性作用，在该区域以外ＳｉＣ粒径变化不影响镀层的结合强度。适当的热处理可提高界面结合力。     

一种碳－碳复合材料长寿命防氧化涂层的失效机制

用液相法联合ＣＶＤ法和硅化法制备了一种碳－碳复合材料复合梯度涂层，在此基础上对这种涂层在氧化过程中的失效机制进行了研究．结果表明：氧化层与液相层界面反应生成的气相产物是涂层失效的根本原因界面上气泡的不均匀形核、长大和破裂导致涂层表面出现孔洞．孔洞处气泡优先形核、长大和破裂并发展成为缺陷而使涂层失效     

n-Al2O3/Ni复合镀层的组织与滑动磨损性能研究

用电刷镀技术制得了镍基n-Al2O3复合镀层，并对镀层的滑动磨损性能进行了试验研究。纳米复合镀层的表面形貌比较细腻，镀层中纳米粒子分布均匀，与基质金属结合紧密。镀层显微硬度达到HV700，比快速镍镀层提高约40％。滑动磨损试验结果表明，随着纳米粒子含量的增大，镀层的耐磨性提高，摩擦系数也呈增大趋势；但当镀层中n-Al2O3粒子的超过2.56%(质量分数）时，镀层的耐磨性显著下降。纳米复合镀层的磨损机制以疲劳磨损为主，而快速镍底层以粘着磨损为主。