沪芦高速公路软土地基设计与研究

软土地基的处理是影响高等级公路工程质量和使用性能的重要因素 ,针对沪芦高速公路的工程特点 ,通过对不同土层力学性能分析 ,地基稳定验算以及沉降计算提出地基处理方案 ,并介绍通过地基处理后获得的显著效果     

Ti-23Al-14Nb-3V合金氩弧焊接头的显微组织及其力学性能

研究了预热对Ｔｉ－２３Ａｌ－１４Ｎｂ－３Ｖ合金焊接性，特别是对消除氩弧焊冷裂纹的作用以及对接头显微组织和力学性能的影响。结果表明，焊前预热可有效降低该合金的冷裂倾向。经预热处理后，焊缝区的结晶层状线消失，热影响区的硬度峰得到缓和，整个焊缝的显微硬度分布趋于均匀，但焊缝区的枝晶发生粗化，热影响区有所扩大。焊件接头的拉伸试验表明，预热可使焊缝区的接头强度系数增加，但无论预热与否，接头强度均低于母材强度，且不显示宏观塑性。     

粉末布法制备SiC/Ti基复合材料

用粉末布法制备了低成本SiC/Ti基复合材料.结果表明,采用合适的轧制参数即可容易地获得厚度合适、均匀的粉末布;热失重分析和热解残余物分析指出用来制备粉末布的有机粘结剂的去除过程分成两个阶段,合理除气后,基本没有残余物.使用真空热压工艺制备的SiC/Ti基复合材料,纤维分布基本均匀,纤维与基体的界面结合良好.     

广州地铁集中冷站的自动控制

本文介绍广州地铁二号线集中冷站的空调制冷自动控制系统的设计，对其控制原理与节能优化进行分析。     

四种国民常用饮水中非挥发性有机物及其致突变活性的比较研究

比较我国居民常用饮水种类自来水、净化水(自来水经净水器过滤)、凉开水(自来水经煮沸后冷却)、纯净水(自来水经以反渗透为主的多重工艺处理)的非挥发性有机物(NOP)污染状况及其致突变活性。结果表明,四种水中检测到的NOP种类分别为自来水39种,净化水40种,凉开水20种,纯净水8种;毛细色谱显示的NOP总丰面积值依次为5.62×109,5.57×109,2.65×109,1.87×109。四种水的移码型及碱基置换型致突变活性依次为:自来水>净化水>凉开水>纯净水,其中自来水在相当1L、2L、4L水量的剂量均为阳性致突变活性,而纯净水在同样的剂量均为阴性。     

WXJB—E型多点温度监测报警仪的研制

本文介绍了 WXJB—E 型多点温度监测报警仪的设计思想、基本原理、技术关键、技术指标及其功能。     

Mannitol and oligosaccharides as new criteria for determining cold tolerance in sugarcane varieties

Sugarcane can be very susceptible to damage by freezes. Freeze-deteriorated cane can cause problems in processing and sometimes leads to a factory shut-down. This study was undertaken during the 2000/2001 harvest season to assess the cold tolerance performance of six commercial sugarcane varieties and to establish new and more sensitive criteria to measure cold tolerance. Two varieties CP 70-321 and CP 79-318, with known cold tolerance, were planted in the study as controls. The other varieties included LHo 83-153, LCP 85-384, HoCP 85-845 and HoCP 91-555. Freezing temperatures occurred on 20 December 2000 when the min. field temperature was −4.4 °C, and again on 21 December, 30 December through 5 January 2001, 9–10 January and 20–21 January. The lowest field temperature recorded was −5.6 °C on 4 January. Freezing conditions prevailed for 8–15 h during each freeze incident. Stalks of all varieties were frozen to the ground following the initial freeze, with freeze cracks evident only after the 4 January freeze. For this study, samples were taken on the date of the first freeze, 20 December, and subsequently again at 7, 14, 22 and 30 days after the first freeze. Criteria used to measure overall stalk cold-tolerance included changes in pH, Brix, dextran (ASI-II method), sucrose, glucose, and fructose concentrations. Mannitol, ethanol and the oligosaccharides, palatinose, leucrose, iso-maltotriose and 1-kestose, were simultaneuously measured using IC-IPAD. Marked differences were observed in most criteria for all varieties, particularly 22 and 30 days after the first freeze. Mannitol was strongly correlated (r²=0.84) with dextran, confirming its use as an indicator for cane dextran deterioration. In comparison, ethanol was only weakly correlated (r²=0.55) with dextran and did not always predict cane dextran deterioration. Iso maltotriose was the most sensitive oligosaccharide indicator of freeze deterioration, although both leucrose and palatinose could be used to confirm whether severe dextran formation (>1500 ppm/Brix) has occurred in cane. Isomaltotriose was strongly correlated (r²=0.89) with dextran and pH (r²=−0.83); pH was also a strong indicator of both dextran (r²=−0.85) and mannitol (r²=−0.92) formation. Four of the varieties, CP 79-318, LCP 85-384, HoCP 85-845 and HoCP 91-555, were shown to be susceptible to other sources of microbial and enzymic deterioration as well as dextran deterioration from Leuconostoc bacteria, especially 30 days after the first freeze. This was indicated by increased glucose/fructose ratios, ethanol formation, changes in 1-kestose concentration, and further sucrose losses.     

Q195冷轧板材轧制困难原因分析

针对部分Q195冷轧板材存在轧制困难的现象，进行了现场检验与分析。带状组织、混晶现象严重导致变形强化系数偏高是造成轧制困难的主要原因。     

Modelling of Al2O3 Powder Compaction with Hot Pressing in a Rigid Die

Computer modelling of hot pressing is provided. Kinetics are described for compaction during hot pressing in a rigid die, and the change in density distribution, irreversible solid phase strain accumulation, and equivalent stresses are studied by means of the finite element method. Shrinkage during the preparation of complex-shaped articles by hot pressing pure Al₂O₃ powder in a graphite die without a protective atmosphere and the physicomechanical properties of the finished article are studied. Calculated and experimental results agree satisfactorily.     

Intelligent Control of Consolidation and Solidification Processes

Intelligent processing of materials (IPM) deals with the integration of process models and in situ sensors into an intelligent process controller to achieve desired material properties. IPM-based control systems recently have been developed for both consolidation and solidification processes. This article explores the application of models based on the finite- element method (FEM) to develop process actuation systems, to design process schedules and component shape, and to develop a control model with which to control the process. The results in this article were presented at the AeroMat ’93 Advanced Aerospace Materials/Processes Conference and Exposition, Anaheim, CA, 7–10 June 1993