多运营商高铁隧道移动网络覆盖方案

高铁移动网络覆盖是国内三大通信运营商的一个重点,而高铁隧道内移动网络覆盖更是运营商的一大难点痛点。文章根据我国中部省份某高铁线路覆盖规划实例,采用“设备+POI+泄漏电缆”模式,即三家运营商信号源设备通过同一POI(point of interface,多系统接入平台)接入,信号输出到泄漏电缆进行隧道覆盖,隧道口场坪站安装宽频切换天线对隧道外进行延伸覆盖,通过链路预算合理布置各运营商主设备信号源,从而实现隧道到室外的无缝覆盖。最后,根据已有成熟网络覆盖解决方案,对未来5G高铁隧道移动网络覆盖方案进行了探讨。     

Deposition of UF5 on the surface of steel material having oxide coating in contact with gaseous UF6

When UF6 is handled in leak tight system, the amount of uranium compound formed on the surface of containers, valves, and others in UF6 handling facilities is not so significant for a short term that special attention has not been given to this problem. The present work was done to throw some more light on this problem based on the recent experiment. We discuss the possibility that the intermolecular transfer of a fluorine atom from UF6 to UF5 may participate in the formation of uranium compound. The discussion includes also the unique features contained in the experimental result, the reaction processes assumed in this problem, and the derivation of a rate equation for expressing the deposition of uranium compound. Furthermore, we propose a new method for determining nonlinear parameters included in a governing differential equation having two variables for expressing the deposition of uranium compound from experimental raw data.     

渣油催化临氢热转化钼铁双金属催化剂的研究

Replacement of precious single metal catalysts with cost-effective, highly-dispersed composite catalysts for catalytic hydrothermal conversion of residue holds tremendous promise for the residue upgrading technologies. Organic metals were added to the feed as the oil-soluble precursors, and transformed into the catalytic active phases in this work. Physical properties and structures of the composite catalysts had been investigated by X-ray fluorescence spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, scanning electron microscope and transmission electron microscopy. The composite catalysts were found to be highly efficient in the catalytic hydrothermal conversion of both model compound and residue. Increased metal dispersion and synergistic effects of two metals played indispensable roles in such catalytic system. Results showed that under the test conditions in the article, the catalyst had the best catalytic performance when the mass ratio of molybdenum to iron was 1.5.     

Two-level intelligent modeling method for the rate of penetration in complex geological drilling process

The rate of penetration (ROP) model is of great importance in achieving a high efficiency in the complex geological drilling process. In this paper, a novel two-level intelligent modeling method is proposed for the ROP considering the drilling characteristics of data incompleteness, couplings, and strong nonlinearities. Firstly, a piecewise cubic Hermite interpolation method is introduced to complete the lost drilling data. Then, a formation drillability (FD) fusion submodel is established by using Nadaboost extreme learning machine (Nadaboost-ELM) algorithm, and the mutual information method is used to obtain the parameters, strongly correlated with the ROP. Finally, a ROP submodel is established by a neural network with radial basis function optimized by the improved particle swarm optimization (RBFNN-IPSO). This two-level ROP model is applied to a real drilling process and the proposed method shows the best performance in ROP prediction as compared with conventional methods. The proposed ROP model provides the basis for intelligent optimization and control in the complex geological drilling process.     

Forging furnace with thermochemical waste-heat recuperation by natural gas reforming: Fuel saving and heat balance

This paper considers thermochemical recuperation (TCR) of waste-heat using natural gas reforming by steam and combustion products. Combustion products contain steam (H₂O), carbon dioxide (CO₂), and ballast nitrogen (N₂). Because endothermic chemical reactions take place, methane steam-dry reforming creates new synthetic fuel that contains valuable combustion components: hydrogen (H₂), carbon monoxide (CO), and unreformed methane (CH₄). There are several advantages to performing TCR in the industrial furnaces: high energy efficiency, high regeneration rate (rate of waste-heat recovery), and low emission of greenhouse gases (CO₂, NO_x). As will be shown, the use of TCR is significantly increasing the efficiency of industrial furnaces – it has been observed that TCR is capable of reducing fuel consumption by nearly 25%. Additionally, increased energy efficiency has a beneficial effect on the environment as it leads to a reduction in greenhouse gas emissions.     

Quasi-static compressive behaviour of aluminium cenosphere syntactic foams

In this paper, cenosphere particles embedded in AA2014 aluminium matrix are used to fabricate syntactic foam by stir casting method. The particle size is about 100?µm and foam density is about 1990?kg?m^?3. Compression tests at strain rate 0.001/s are performed on foam samples to characterise their mechanical properties which are then used in numerical analysis on commercial finite element analysis software ABAQUS/CAE with isotropic elastic-plastic material model. Experimental and numerical results show good conformity in deformation behaviour with elastic and plateau zones showing average deviations less than 5% and 20%, respectively. Foams showed high yield stress and energy absorption capabilities that can be useful in making blast and impact resistant structures.     

计及Spark和属性权重的售电套餐推荐方法

针对电力市场用户群庞大，交易过程中售电套餐选择困难的问题，在Spark环境下设计了一种售电套餐推荐方法，同时也解决了售电套餐推荐过程中在大数据环境下的可扩展性及实时性问题。首先，计算出每个套餐属性的权重值，从而计算得到售电套餐综合相似度。然后，计及用户和套餐两方面提出一种售电套餐推荐方法，实现售电套餐的精准推荐。实验表明，提出的推荐方法能够明显提高推荐的准确度，并且在分布式环境下具有良好的推荐效率和可扩展性。     

应用膨胀算法提取目标的直接定位算法

为了解决被动雷达系统中的多发射源定位问题，提出了一种基于多重信号分类(MUSIC)算法和图像膨胀(IE)算法的直接定位方法。该方法结合了谱分析中的MUSIC思想，通过对接收量测协方差矩阵进行特征分析求解目标的位置。首先，在目标个数未知的前提下，利用Akaike信息准则(AIC)来确定模型阶数；然后，推导了基于MUSIC的定位代价函数；之后，利用图像膨胀算法处理得到的代价函数平面；最后，膨胀处理后的输出为目标个数及目标位置的估计值。提出的算法有效地解决了目标检测及提取的问题，能够确定多个目标的位置坐标，为后续的定位性能分析提供可能性，也保证了算法的完整性。进一步地分析了多个临近目标情况下影响目标提取性能的主要因素。     

Why do small business butcher shops fail to fully implement HACCP?

This study aims to assess the degree of HACCP implementation in small business butcher shops and understand which factors most influence butchers' intention to fully implement it, through the application of the Theory of Planned Behaviour. One hundred and one butchers managing or owning small butcher's responded to the interview regarding their Attitudes, Subjective Norm, Perceived Behavioural Control, Personal Norm, and Knowledge with regard to their Intention to fully implement a HACCP system in their shops. Before the interviews, a certified veterinarian visited all the shops. Visits included an inspection of the establishments using the Official Portuguese Control Plan checklist for meat retailers. Conformance level measured past performance regarding food safety practices. Based on past performance, butchers were divided into “high performers” and “low performers”. “High performers” yielded high values of Attitude and Intention towards the Behaviour. For these, Attitude and Personal Norm emerge as predictors of the Intention to fully implement a HACCP system. For “low performers”, Personal Norm was the strongest predictor of Intention, with results pointing to the need for an intervention from the authorities to promote increased conformance to food safety practices. For both groups, neither Social Norm nor Perceived Behavioural Control acted as significant predictors of Intention.