修正步冷温度曲线试验研究

按修正步冷温度曲线对经步冷脆化的 2 .2 5Cr 1Mo和在加氢反应器内运行 5a的 2 2 5Cr 1Mo试块进行了修正步冷试验 ,评定了材料的回火脆性。结果表明 ,按修正步冷曲线进行修正步冷试验能使已经脆化的材料进一步脆化 ,为加氢反应器材料损伤的研究提供了一条途径。     

臭氧法水处理在空调冷却水系统中的应用

探讨了臭氧法杀菌灭藻，缓蚀，阻垢的机理，认为臭氧法可用于空调冷却水处理，并给出在工程设计中的应用方法。     

对高炉冷却壁设计参数的探讨

通过炉衬、冷却壁、炉壳等与炉内温度之间的传热计算，对冷却壁的设计参数进行了搪塞分析，并提出了推荐的冷却壁设计参数。     

离子静电水处理技术在循环冷却水中的应用

简要介绍了离子静电水处理技术杀菌、灭藻、防垢阻垢的机理，及在循环冷却水系统中的应用情况。     

中厚板汽雾冷却技术的开发及应用

为解决济钢中板厂冷床能力不足问题，对汽雾冷却系统的技术原理、系统组成进行了研究及实际应用；应用汽雾冷却系统后，在保持钢板组织和力学性能不受影响的前提下，提高了钢板的降温速度，加快了生产节奏；经汽雾冷却的钢板，表面氧化层减薄1／2。     

利用空间多普勒调谐技术冷却原子及其速度单一化

本文理论计算了用圆锥管内多次全反射激光而产生的多普勒频移来冷却原子束的机制。给出了最佳冷却原子束的圆锥管的夹角、长度、反射次数及激光入、出射角等参数。理论计算了原子束经过圆锥管冷却的速度分布情况。数值计算结果表明：采用两个长１３０ｃｍ的锥形管来冷却原子束，选用合适的失谐量可使极大部分速度小于１２００ｍ／ｓ的原子冷却到８ｌｍ／ｓ，并且可得到单一速度的高亮度的原子束。     

Effects of the cryogenic cooling on the fatigue strength of the AISI 304 stainless steel ground components

For environmental considerations, the substitution of the conventionally used oil-based grinding fluids has nowadays become strongly recommended. Although several alternatives have been proposed, cryogenic cooling by liquid nitrogen is the non-polluting coolant that has been given relatively more attention because of its very low temperature. In this investigation, in order to contribute to developing this promising cooling mode, its beneficial effects on the ground surface integrity of the AISI 304 stainless steel and their consequences on the fatigue lifetime are explored. Results of this investigation show that grinding under cryogenic cooling mode generates surfaces with lower roughness, less defects, higher work hardening and less tensile residual stresses than those obtained on surfaces ground under oil-based grinding fluid. These surface enhancements result into substantial improvements in the fatigue behaviour of components ground under this cooling mode. An increasing rate of almost 15% of the endurance limit at 2 × 10⁶ cycles could be realized. SEM analyses of the fatigue fracture surfaces have shown that the fatigue cracks observed on the specimens ground under cryogenic cooling are shorter (i.e., 30-50 μm) than those generated under oil-based cooling mode (i.e., 150-200 μm). The realized improvements in the surface integrity and in the fatigue behaviour are thought to be related to the reduction of the grinding zone temperature observed under cryogenic cooling, as no significant differences between the grinding force components for both cooling modes have been observed.     

内燃机车临时补水设备的设计与应用

针对内燃机车“途中缺水”故障 ,设计并安装临时补水设备 ,解决了电化区段临时补水的问题 ,满足了内燃机车“不停车、不停机”即可补水的要求。     

轧后穿水冷却工艺对棒材组织性能的影响

针对轧机产量提高后冷床冷却能力不足的问题 ,研制开发了棒材轧后穿水冷却技术。通过对小规格 2 0MnSiV热轧带肋钢筋进行轧后穿水冷却 ,钢材上冷床温度降低了 90～ 110℃ ,提高了产品质量 ,改善了各项力学性能 ,抗拉强度平均提高了 3 5～ 40MPa ,钢材性能合格率由 97.5 %提高到了 99.6% ,解决了冷床冷却能力不足、制约生产的瓶颈问题。     

冷却水污垢及其对冷却器换热的影响

分析了冷却器的结垢机理 ,提出了冷却器污垢层、污垢热阻随运行时间的规律 ,以及污垢热阻与换热系数、换热面积的关系式 ,并通过算例阐述了污垢热阻对冷却器的影响程度 ,进而定性地分析了污垢热阻对空分装置的影响。