The effect of a solid additive on rolling fatigue life

Behaviour of a series of lubricant oils and the effect of a non stoichiometric inorganic compound, as solid extreme pressure additive, on rolling fatigue life are studied using the rolling four-ball accelerated service simulation test proposed by Barwell and Scott. The results show, in all tested cases, the remarkable efficacy of this type of additive. The Total Acidity Number (tan) was found to increase with performance time for the case of the base lubricant, while for the oils with additives, it remained at its constant low value. This led to a proposal of a possible mechanism of the additive performance in the rolling process.     

轧机主传动万向联轴器辊端接头结构探讨

分析了衬板槽平面与叉头十字轴孔轴线的相对位置对辊端接头应力的影响 ,研究了轧辊扁头与衬板之间间隙所产生的冲击和应力集中 ,讨论了辊端接头中部过渡段结构对应力分布和制造质量的影响。提出辊端接头结构设计的优化方案     

冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

Failure analysis used for remanufacturing of steel rolling components

The guide-pieces, used in the process line of steel rolling, were the important components. The guidepieces, which were slide contacting with the rolled-piece, had a high temperature and high speed. The wear was very serious. The results from failure analysis showed that there were three failure forms in the guide-pieces: the first was the wear during heat friction, the second was the heat fatigue under the cycle of deep heating and deep cooling, and the third was the impact rupture. Among them, the wear was the main reason. To the wear of guidepieces, there were four mechanisms, namely abrasive wear, adhesive wear, fatigue wear and corrosion wear. The failure analysis to the guide-piece laid the foundation for its remanufacturing. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China     

Finite‐Element Implementation of a Self‐consistent Texture Model with a Hardening Law Based on Dislocation Densities

A self‐consistent texture model is implemented in the finite‐element code ABAQUS/Explicit®. Hardening of the slip systems is described by evolution laws for dislocation densities, and the Bauschinger effect is included. With these ingredients the cold rolling of an IF‐steel is simulated and the evolution of texture and anisotropy is examined. The use of the dislocation based hardening law is found to have a significant effect on the evolution of the anisotropic yield surface, but only very little influence on the texture. Furthermore, the hardening model is used to investigate the evolution of dislocation densities in differently oriented grains during plane strain compression. It is found that the dislocation density varies greatly depending on orientation, an observation which can help to explain the orientation dependence of recrystallization.     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

浅议铵梯炸药质量检验中的三个问题

文章探讨了GB 12437-2000标准规定的产品检验项目中,中包浸水试验的科学性问题和对批产品进行抽样时的样本代表性问题以及使用多段爆速仪测试爆速时应注意的样本量问题.     

摩擦焊在钢制实心抽油杆修复中的应用

通过对焊接工艺及焊后热处理工艺优化，采用摩擦焊接技术对报废抽油杆中仍有使用寿命的杆头与杆体进行了拼接，获得了性能达标的抽油杆。从而提高了旧杆的修复率．降低了采油成本。该技术可在抽油杆修复及相关行业进行推广应用。     

植筋施工工艺

以某网球馆改造工程为例 ,就植筋技术的概念及所用材料进行了介绍 ,详细阐述了其施工工艺流程及措施 ,指出植筋技术具有工艺简单、操作方便、造价相对较低等优点     

铁素体球墨铸铁与20钢的闪光对焊

试验使用铁素体球墨铸铁和20钢的实心棒料进行了闪光对焊，通过改变次级电压4～8级，通电时间3～5s，观察其焊接接头组织的变化并测定其抗拉强度。结果表明，接头由三个区组成；当通电时间一定时，抗拉强度随次级电压的升高先减小后增大；当次级电压一定时，抗拉强度随通电时间的增加而增大。在次级电压为8级、通电时间为5s时，抗拉强度达最大值，为370．8MPa，是20钢母材的90.4％，是球墨铸铁母材的83.7％。