Fatigue Behavior and Retrofit Investigation of Distortion-Induced Web Gap Cracking

This paper studies a Kansas Department of Transportation welded plate girder bridge that developed fatigue cracks at small web gaps close to the girder top flange. Repair had been previously performed by softening the connection plate end with a slot retrofit, but cracks were recently found to have reinitiated at some of the repaired details and are again propagating. A comprehensive finite-element method study was performed to investigate the cracking behavior observed in the bridge and to recommend appropriate measures for future bridge retrofit. The analytical results show that stresses developed at the top flange web gaps could exceed yielding under the loading of an HS15 fatigue truck. The current slot repair used in the bridge was found to have introduced higher magnitude fatigue stresses in the web gap. To achieve a permanent repair of the bridge, it is recommended that a welded connection plate to flange attachment be used during future bridge retrofit. The web gap details should be able to withstand unlimited number of load cycles once this additional repair is performed.     

行政权力腐败的模型分析及治理对策

腐败是与政府行政权力相伴生的痼疾，既是一个历史现象又是一个国际现象。贪污腐败和寻租腐败是委托一代理模型中最典型的腐败方式，文章在此基础上对贪污腐败和寻租腐败进行成本一收益分析和市场均衡分析，并探讨治理行政权力腐败的有效途径。     

Significance of the elastic peak stress evaluated by FE analyses at the point of singularity of sharp V-notched components

The paper presents an expression useful to estimate the notch stress intensity factor (NSIF) from finite element analyses carried out by using a mesh pattern with a constant element size. The evaluation of the NSIF from a numerical analysis of the local stress field usually requires very refined meshes and then large computational effort. The usefulness of the presented expression is that (i) only the elastic peak stress numerically evaluated at the V‐notch tip is needed and no longer the whole stress–distance set of data; (ii) the adopted meshes are rather coarse if compared to those necessary for the evaluation of the whole local stress field. The proposed expression needs the evaluation of a virtual V‐notch tip radius, i.e. the radius which would produce the same elastic peak stress than that calculated by FEM at the sharp V‐notch tip by means of a given mesh pattern. Once such a radius has been theoretically determined for a given geometry, the expression can be applied in a wide range of notch depths and opening angles.     

Finite-element analysis and experimental study on tensile fatigue behaviour of bitumen–stone adhesion

Tensile fatigue behaviours of bitumen–stone adhesion were investigated using a dynamic mechanics analyser under stress‐controlled mode at two temperatures of 5 and 25°C and various controlled‐stress levels. Failure characteristics including interfacial failure and cohesive failure were examined using image analysis of fracture surfaces. Finite‐element analysis on stress distributions was conducted under different temperatures, film thickness and interfacial bonding conditions. A Coulomb–Mohr like criterion in combination with shear and normal stresses is proposed to deal with the extreme thin adhesive layer, which can be further simplified into an adhesive zone without significant loss of accuracy for stress analysis.     

Developing Cost Response Models for Company-Level Cost Flow Forecasting of Project-Based Corporations

The difficulty in applying the standard curve (S-curve) and cost-schedule integration (CSI) techniques for company-level cost flow forecasting in a project-based industry is the prerequisite of forecasting future unknown individual projects and contract classifications. By analyzing cost flows at the company level through a pool of macroeconomic and internal financial data, this paper proposes an innovative approach to firm-specific model estimation. First, a series of data transformations introduce linear relationships between cost, macroeconomic, and internal financial variables. Second, multivariate regression analysis is employed for initial model building. Third, for the purposes of model restructuring, a subsequent application of Yule–Walker estimates and incomplete principal component analysis is used. This paper uses a sample of four project-based construction firms to demonstrate model performance. Using this methodology, mean absolute percentage error (MAPE) values of the forecasting models range from 0.27 to 0.60%. As such, the transformed cost, macroeconomic, internal financial data could strongly predict company-level cost flow forecasting. While converting the predicted cumulative cost data to periodic cost flows, the MAPE values were augmented, ranging from 7.04 to 17.55%, thus, requiring future research.     

Free-Edge and Ply Cracking Effect in Angle-Ply Laminated Composites Subjected to In-Plane Loads

This paper presents a semianalytical method for the prediction of interlaminar stresses and displacements near the free edges and ply cracks in general angle-ply laminates subjected to biaxial extensions and/or in plane shear deformation. The method is based on a state space representation of the three-dimensional equations of elasticity. Numerical solutions are obtained by using layer refinement in the through thickness direction and Fourier series expansion in the other directions. By this approach, an angle-ply laminate may be composed of an arbitrary number of monoclinic layers and each layer may have different material property and thickness. This method guarantees continuous fields of all interlaminar stresses across interfaces between material layers. Numerical results are compared with those obtained from other methods. It is found that the theory provides a satisfactory approximation to the stress singularities near the free edges and ply cracks. Numerical solutions for antisymmetric laminates under extension and general laminates under shearing are new in the literature and can be used as benchmarks for validating new models.     

Applications of the discrete element method in mechanical engineering

Compared to other fields of engineering, in mechanical engineering, the Discrete Element Method (DEM) is not yet a well known method. Nevertheless, there is a variety of simulation problems where the method has obvious advantages due to its meshless nature. For problems where several free bodies can collide and break after having been largely deformed, the DEM is the method of choice. Neighborhood search and collision detection between bodies as well as the separation of large solids into smaller particles are naturally incorporated in the method. The main DEM algorithm consists of a relatively simple loop that basically contains the three substeps contact detection, force computation and integration. However, there exists a large variety of different algorithms to choose the substeps to compose the optimal method for a given problem. In this contribution, we describe the dynamics of particle systems together with appropriate numerical integration schemes and give an overview over different types of particle interactions that can be composed to adapt the method to fit to a given simulation problem. Surface triangulations are used to model complicated, non-convex bodies in contact with particle systems. The capabilities of the method are finally demonstrated by means of application examples. Commemorative Contribution.     

Mining for trigger events with survival analysis

This paper discusses a new application of data mining, quantifying the importance of responding to trigger events with reactive contacts. Trigger events happen during a customer’s lifecycle and indicate some change in the relationship with the company. If detected early, the company can respond to the problem and retain the customer; otherwise the customer may switch to another company. It is usually easy to identify many potential trigger events. What is needed is a way of prioritizing which events demand interventions. We conceptualize the trigger event problem and show how survival analysis can be used to quantify the importance of addressing various trigger events. The method is illustrated on four real data sets from different industries and countries.     

超分子主体化合物在分析化学中的应用研究进展

综述了近年来超分子主体化合物在分析化学领域的应用研究与进展。分别以冠醚、环糊精、杯芳烃、卟啉4类超分子为主体功能化合物的研究进行了详细的评述，并对这几类主体化合物在分析化学中的应用研究进行了展望。     

An analysis of shielding against DC magnetic fields generated by electric railways. Evaluation of effective permeability of fine structure

This paper describes an effective analysis of magnetic shielding based on homogenization. The analyses become time‐consuming if the problems include the magnetic substances having fine structure. The homogenization of the structure makes it possible to analyze effectively the magnetic fields. The authors introduce a method to estimate the effective permeability of the homogenized substance. This method can be applied to any periodic structure made of magnetic substance. The magnetic shielding effects by the structures against direct‐current (DC) fields generated by electric railways are analyzed by using the present method. As a result, it is found that the overhead way and the protective fence near the railway work as a magnetic shield, whose effects can be improved by appropriate arrangement of those constructions. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(4): 7–15, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20310