锅炉过热器/再热器管道热流密度的评估方法

通过建立数值模型进行编程计算,分析了锅炉过热器/再热器管道在不同的管道几何尺寸、烟气温度、蒸汽流量和温度下,各个界面热流密度的变化情况。通过回归分析得到了热流密度与管道内壁侧氧化层厚度和运行时间的关系表达式,即热流密度的评估关系式。     

一种矩形微米流道的加工与流量测定

介绍了一种比较成熟的矩形微米流道(微槽道)加工工艺,利用厚胶光刻工艺在硅片上制备胶模板,进而在该模板上用高分子聚合物PDMS(Polydimethylsiloxane,聚二甲基硅氧烷)制作了微米量级的微槽道(高、宽范围20~100μm),对制备的微槽道的几何精确度进行了20×100倍放大显微观测,对其流量特性进行了实验测定.实验结果与泊肃叶理论公式(NS方程的管流表达式)相对比,可以看到在微米量级的矩形微流道中,泊肃叶公式仍然适用.     

新型横向磁场电机的标量磁位三维磁场分析与参数计算

提出了一种新型横向磁场电机（TFM），定子采用E型铁心，可以大大降低加工难度和制造成本。但是，该电机磁路复杂，需采用三维场场进行分析。在三维有限元磁场中，如果对电流区域进行适当处理，采用标量磁位进行分析，与采用矢量磁位相比，可大大提高计算速度。对电流区域在三维磁场计算中的处理方法进行了推导，根据所推导的原理编制三维有限元软件，利用该软件对样机磁场进行计算。试验结果表明了该方法的正确性。     

圆管临界热流密度的流体模化

为了评价现有的临界热流密度(CHF)流体模化技术,在氟里昂-12热工实验装置上完成了φ202.5圆管CHF实验。在此基础上,用不同的数据源,比较了Ahmad补偿失真模型、鲁钟琪模型、Groeneveld模型和Stevens-Kirby经验比例因子模型的预测精度和适用范围,为复杂流道中的CHF流体模化研究奠定了基础。     

岷江试验堆Q15孔道中子谱测量试验的研究

为了确定岷江试验堆(简称MJTR)堆芯铍反射层内中子能量E >1.0MeV的快中子注量率,采用一组中子探测片测量了岷江试验堆内第一层铍反射层外Q15孔道内的快中子注量率谱,并由测量谱求得各阈能探测片的快中子反应的谱平均截面和该孔道测量点位置的快中子注量率。结果表明,铍反射层内快中子(E>1.0MeV)注量率为1.985×1012 cm-2·s-1,MJTR每运行一段,铍反射层内快中子(E>1.0MeV)积分注量最大可达1.54×1018cm-2。通过本次试验研究,为更好的开发利用MJTR提供了试验依据。     

An Observing Method for Flux and Speed with Direct Torque Control

An observing method for stator flux and rotor flux is presented. Based on the proposed flux observing method, a novel speed estimator has been designed. At last, the speed estimator combined with the flux observing is applied in the direct torque control system without speed sensor. The simulation results show that these methods can improve the accuracy of speed observing and the low speed performance of direct torque control system, and strengthen the robustness of system.     

Effect of Carbon Properties on Melting Behavior of Mold Fluxes for Continuous Casting of Steels

Mold fluxes are synthetic slags used to coverthe liquid steel meniscus during continuous castingof steel.The flux,whichis continuously fed on thesurface of liquid pool during casting,melts first andthenflowsintothe gap between mold wall and solid-ified steel shell.It is well known that the perform-ance of the flux can greatly affect both the castingoperation and product quality.Because of its i mpor-tance,intensiveinvestigations have been performed,and considerable progress has been made[1-6].…     

铝合金熔剂的研究

本文介绍了熔剂在铝合金熔炼过程中的作用,熔剂的分类和要求,常用熔剂的组成,适用范围及使用方法等。     

Characteristics of Ions Emitted from Laser-Induced Silver Plasma

In this work, study of laser-induced ions is presented. The plasma was produced by focusing a Nd：YAG laser, with a wavelength of 1064 nm, a pulsed width of 9-14 ns, a power of 1.1 MW and energy of 10 mJ, on silver target in vacuum （10-3 Torr= 1.3332 Pa）. The characteristics of ion streams were investigated by CR-39 detectors located at angles of 0°, 30°, 60° and 90° with respect to normal of the target. The distance between the silver target and each detector was 11 cm. The energy of silver ions was found ranging from 1.5 eV to 1.06E4 eV. There was a high concentration of ions with low energy as compared to those with high energy, showing the energy distribution amongst the ions. The flux of ions was maximum in the axial direction which was decreasing with the angle increase with respect to normal of the target, and finally became minimum in the radial direction. Hence the silver ions have shown anisotropic behaviour.     

树脂芯助焊剂性能的基础研究

焊锡丝主要应用于仪器、仪表、各种家用电器等的焊接、补焊以及维修,而其焊接质量的好坏不仅取决于焊锡丝的合金材料,更取决于其树脂芯助焊剂的性能,通过大量的实验对影响其性能的因素进行了分析,并对可焊性进行测试,从而制备出诸如卤素含量低,扩展率好等综合性能优良的树脂芯助焊剂.