新型技术用于乳状液膜法脱酚的进一步研究

本文对模拟的含酚废水,采用新型技术对乳状液膜法脱酚进行了进一步的探讨。对所采用的制乳设备———撞击流-旋转填料床对制乳率、提取设备———旋转填料床对脱酚率、破乳设备———无机微孔膜法破乳的重要参数(如透过压方式、膜孔径等对膜通量和破乳率的影响)进行了研究。并且讨论了破乳后的油相回用情况。实验结果表明:撞击流-旋转填料床的制乳效率可达99.90 %以上,脱酚率可达99%左右,且瞬间完成;膜孔径越小,破乳率越高,膜通量越小;外压内抽方式的破乳效果优于单外压方式的破乳效果。对于粒径为5～2 5 μm乳液,用膜孔径为2 .0 μm的SiC微孔膜,在外压为6 0kPa、内负压为30kPa的外压内抽破乳方式下破乳,破乳率可达96 .4 % ,膜通量可达90 0L·(m2 ·h) -1。     

动力煤洗前干法脱粉新技术

介绍了煤炭振动流化床气力分级新技术的工作原理和特点;通过该机组在郑煤集团米村矿的应用实例,说明了该技术可实现煤炭选前0～10mm内任一粒度干法分级,从而降低动力煤洗选粒度下限,优化产品结构,减少煤泥量,提高企业经济效益。     

Phase holdup and liquid dispersion in gas-liquid-solid circulating fluidized beds

Axial and radial profiles of gas and solids holdups have been studied in agas-liquid-solid circulating fluidized bed at 140mm i.d..Experimental results indicate that the axialand radial profiles of gas and solids holdups are more uniform than those in a conventionalfluidized bed.Axial and radial liquid dispersion coefficients in the gas-liquid-solid circulating fluidizedbed are investigated for the first time.It is found that axial and radial liquid dispersioncoefficients increases with increaes in gas velocity and solids holdup.The liquid velocity has littleinfluence on the axial liquid dispersion coefficient,but would adversely affect the redial liquiddispersion coefficient.It can be concluded that the gas-liquid-solid circulating fluidized bed hasadvantages such as better interphase contact and lower liquid dispersion along the axial directionover the expanded bed.     

Estimating discharge in gravel‐bed river using non‐contact ground‐penetrating and surface‐velocity radars

Discharge measurement is a critical task for gravel‐bed channels. Under high‐flow conditions, the elevation of the riverbed changes significantly by intensive torrential flow. The stage–discharge relations commonly used for stream discharge estimation may no longer be adequate. The contact‐type velocity measuring is also subject to measurement errors and/or instrument failures by the high‐flow velocities, driftwood, stumps, and debris. This study developed a new real‐time method to estimate river discharge in gravel‐bed channels. A systematic measuring technology combining ground‐penetrating radar and surface‐velocity radar was employed. The rating curves representing the relations of water surface velocity to the channel cross‐sectional mean velocity and flow area were established. Stream discharge was then deduced from the resulting mean velocity and flow area. The proposed method was examined in a steep gravel‐bed reach of the Cho‐Shui River in central Taiwan. The estimated stream discharge during three flood events were compared to the prediction by using the stage–discharge relation and the index‐velocity method. The proposed method of this study is capable of computing reasonable values of discharge for an entire flood hydrograph, whereas the other two methods tend to produce large extrapolation errors. Moreover, when the computed discharge is used in 2D flood flow simulation, the proposed method demonstrates better performance than the commonly used stage–discharge and index‐velocity methods.     

烯（醚）醛一步法合成异戊二烯技术开发—基础理论研究进展

本文介绍了烯(醚)醛一步法合成异戊二烯技术开发中,基础理论研究工作的进展,其中包括化学热力学、化学动力学、再生烧炭本征动力学和扩散动力学等理论研究。并针对该反应特征进行了化学反应规律和流动传递规律的研究。建立了流化床反应器数模和流化床再生器数模,为工程技术开发提供理论依据。     

Unipol气相法聚烯烃液体催化剂技术进展

介绍了Unipol气相法聚烯烃工艺液体催化剂的成分、加入反应器的方式和喷嘴结构及控制催化剂液滴尺寸方法等方面的最新进展情况。     

Cocurrent downflow circulating fluidized bed (downer) reactors — A state of the art review

In the last decade, cocurrent downflow circulating fluidized bed reactors, called “downer” reactors, have been proposed as an alternative to upflow circulating fluidized bed, or “riser”, reactors. In this paper, published results on downer studies are summarized and future directions of research are recommended. Downer reactors are shown to have several distinct advantages over upflow circulating fluidized bed reactors and can potentially be used in many industrial processes, mainly due to a more uniform gas and solids flow structure compared with risers.     

流化床电化学反应器研究进展

流化床电化学反应器是一种三维颗粒电极反应器,以其比表面积大、传质速率高而备受关注。就流化床电化学反应器在导电机理、数学模型、结构放大以及应用领域的研究现状和进展进行了综述,阐明了该类反应器开发、设计和模型化方面存在的问题,并提出了研究方向。     

Polymer waste recycling over “used” catalysts

Catalytic degradation of high-density polyethylene (HDPE) was carried out under nitrogen using a laboratory fluidised bed reactor operating at 360 °C with catalyst to polymer feed ratio of 2:1 and at 450 °C with catalyst to polymer feed ratio of 6:1 under atmospheric pressure. The catalysts used in this study were ZSM-5, US-Y, ASA, fresh FCC (fluid catalytic cracking) commercial catalyst (Cat-A) and equilibrium FCC catalysts with different levels of metal poisoning were studied. The initial results for polymer degradation at 360 °C (catalyst to polymer ratio of 2:1) in a fluidised bed reactor in terms of the yield of volatile hydrocarbon products were: model catalysts>commercial FCC catalyst>E-Cats. However, when the process conditions more closely resembled to FCC conditions, the fresh commercial FCC catalyst was more favourable in terms of the yield of volatile hydrocarbon products. The degradation of HDPE over E-Cats although reduced was similar to ASA in product selectivity and yield, and the level of metal contamination did not affect the product stream generated. A simple economic evaluation of polymer recycling process is reported showing that a catalytic system based on E-Cats appears comparable in costs to a commercial thermal cracking plant.     

AlCl3/活性炭催化甲基三氯硅烷与低沸物再分配反应研究

甲基三氯硅烷(M1)与低沸物(LBR)是工业上"直接法"生产二甲基二氯硅烷单体过程中产生的副产物,两者之间通过再分配反应可转化为高价值的有机硅单体.以活性炭为载体,采用浸渍蒸发煅烧法制备了负载型AlCl3固体酸催化剂,在固定床反应器中进行甲基三氯硅烷与低沸物的再分配反应,制得二甲基二氯硅烷和三甲基氯硅烷.考察了活性炭载体预处理方式及反应条件对再分配反应的影响.结果表明,经过高温扩孔处理的活性炭载体负载的AlCl3催化剂具有较好的反应活性;优化的反应条件为:W(M1/LBR)为2.0～3.0,反应温度为310℃,LHSV为1.5 h-1;该催化剂的制备过程简单,催化反应条件温和且表现出良好的催化稳定性.