过磷酸钙含氟尾气处理的新方法

对动态泡沫床处理过磷酸钙含氟尾气的有关技术及费用作了说明 ,指出该方法费用高 ;提出一种新方法 ,该方法不加任何化学助剂 ,采用水作吸收剂 ,只需改变动态泡沫床一些设计参数和选用一种特殊的喷头 (喷头周围设计 1个圆锥形死角区 ,使含氟气体不可能进入该区 )避免了硅胶堵塞。该方法已在湖南浦市化工总厂运行 1年多未发现堵塞 ,同时该法投资少、能耗低、排放尾气达标     

对甲醇精馏几个问题的认识

简述甲醇精馏三塔流程原理 ,分析了加压精馏塔及常压精馏塔物料和热量平衡关系 ,提出了操作中应注意的事项     

Soap‐free emulsion copolymerization of perfluoroalkyl acrylates in the presence of a reactive surfactant

Soap‐free emulsion copolymerization of perfluoroalkyl acrylate (FA)/methyl methacrylate (MMA)/n‐butyl acrylate (n‐BA) was carried out in the presence of sodium 2‐acrylamide‐2‐methyl propanesulfonate (AMPSNa) as a reactive surfactant and potassium persulfate (KPS) as an initiator. An analysis of the effects of concentration of AMPSNa, KPS, FA as well as polymerization temperature on the kinetic features (rate of polymerization) and colloidal characteristics (mean particle diameter, particle disperse index, particle numbers, and surface charge density) was followed. NMR, FTIR, AFM, and fluorine‐selective electrode analysis were used to characterize the composition and morphology of the FA copolymers. Both AFM analysis and contact angle measurements strongly implied that the fluorinated segments migrated to the outmost surface and created films with lower surface energy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2438–2444, 2007     

应用WCA微扰理论推算非极性液体比热容的新方法

本文首次将统计热力学的Ｗｅｅｋｓ－Ｃｈａｎｄｌｅｒ－Ａｎｄｅｒｓｏｎ（简称ＷＣＡ）微扰理论应用于非极性液体定容比热容和定压比热容的推算，用一些液体的ｐ－ｖ－Ｔ实验数据拟合了理论中所用ＬＪ势能函数的势能参数，并提出一个通用关联式。本文方法具有通用性，在编制的计算程序中只需输入物质的临界温度、临界比容、偏心因子等就能算出相应的比热容，工程应用十分方便。     

Effect of Twin-Plane Reentrant Edge on the Coarsening Behavior of Barium Titanate Grains

When BaTiO₃ ceramics were sintered at relatively low temperatures (≤1250°C), the grains with reentrant edges caused by a (111) double twin grew exclusively. As a result, a microstructure with a bimodal grain-size distribution composed of platelike large grains and fine matrix grains was obtained. In contrast, at the usual sintering temperature between 1250° and 1350°C, grains containing a (111) double twin did not exhibit any growth advantage. In this case, a coarse and uniform microstructure was obtained. When this coarse-grained specimen was further heat-treated at 1365°C, the grains possessing a double twin were observed to grow exclusively again. The results were explained in terms of a coarsening process controlled by two-dimensional nucleation.     

无机颜料的表面处理

介绍了无机颜料表面处理的作用及实现途径,并对其作用机理进行了分析,还叙述了表面活性剂的选择和处理方式。     

Assessing the predictive capability of two‐phase models for the mechanical behavior of alumina/epoxy nanocomposites

A review of analytical modeling of particulate reinforcement is made as a prelude to the problem of microstructural inhomogeneity in nanocomposite materials. Noting the inevitability of dispersion nonuniformity, and variations in agglomerate morphology and filler‐matrix interaction, the need to question the application of such models to novel materials arises. Employing the mechanical properties of alumina/epoxy nanocomposites, with known dispersion characteristics, an evaluation of the predictive capability of various models for Young's modulus, strength, and failure strain is made. Comparison between models is accompanied by a discussion of the parameters used in the fitting of macroscopic behavior to microstructural features. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 869–879, 2005     

Composites based on eucalyptus tar pitch/castor oil polyurethane and short sisal fibers

Polymeric materials are being developed with renewable resources to promote industrial progress with environmentally friendly technologies. For this reason, polyurethane samples were prepared with 4,4′‐diphenylmethane diisocyanate (NCO/OH = 1), eucalyptus tar pitch (biopitch), castor oil as a polyol, and dibutyltin dilaurate as a catalyst. These materials were reinforced with different contents of short sisal fibers (0, 2.5, 5.0, 7.5, and 10.0%) and were prepared by resin‐transfer molding. The composites were characterized by IR absorption spectroscopy, thermal analysis (thermogravimetry and differential scanning calorimetry), impact resistance, scanning electron microscopy, and water absorption resistance. These materials showed hydrophobic characteristics, despite the addition of sisal fibers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3797–3802, 2003     

Vinyl‐containing silicone resin as the crosslinking agent of heat‐curable silicone rubber

Heat‐curable silicone rubber (HCSR) was prepared by using vinyl‐containing silicone resin (VSR) as the crosslinking agent instead of polyvinylsilicone oil (C gum). Mechanical properties and crosslink density of the vulcanizates were measured. The results indicate that VSR is a good crosslinking agent for HCSR. The tensile strength, tearing strength, elongation at break, and hardness of the vulcanizate can reach 10.2 MPa, 29.1 kN/m, 720%, and 58 SHA, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3123–3127, 2002; DOI 10.1002/app.10054