Effect of pretreatments and freezing rate on the firmness of potato tissue after a freeze–thaw cycle

The texture of potato tissue after a freeze–thaw process using different freezing rates and different pretreatments was analysed, in order to select the best strategy for optimum preservation of the textural characteristics of pre‐frozen potato. Ten blanching conditions were tested and a two‐step blanching process with calcium chloride (0.07 g mL^?1) proved the most effective in protecting the tissue after a freeze–thaw process (maximum load force around 10–55% of the raw tissue, depending on potato batch, for air‐blast freezing and 20–60% for immersion freezing). Vacuum impregnation at 100 and 400 mbar, even when followed by different pre‐drying treatments to remove excess water, was very detrimental to resistance to a freeze–thaw process (maximum load force below 10% of the raw tissue for air‐blast freezing and below 20% for immersion freezing). Microstructure analysis confirmed better tissue integrity retention with ethyleneglycol immersion freezing instead of air‐freezing. Differences were found between batches with a 6‐month difference in storage time, indicating that the fresher batch was more suitable for freezing.     

High‐pressure processing effects on the mechanical,barrier and mass transfer properties of food packaging flexible structures: a critical review

Food products can be high‐pressure processed (HPP) either in bulk or prepackaged in flexible or semi‐rigid packaging materials. In the latter case the packaging material is subjected, together with the food, to high‐pressure treatment. A number of studies have been performed to quantify the effects of high‐pressure processing on the physical and barrier properties of the packaging material, since the integrity of the package during and after processing is of paramount importance to the safety and quality of the food product. This article reviews the results of published research concerning the effect of HPP on packaging materials. Copyright © 2004 John Wiley & Sons, Ltd.     

三峡工地高压供电线路故障判断方法的探讨

高压供电设备故障特别是输电线路的高压接地故障对工地的影响是相当大的。由于接地故障为隐性故障，没有明显的物理现象，且若是长期接地可能会发展成较为严重的两相或三相短路故障，使系统解列运行直至崩溃；由于工地流动人员较多，还易造成电击事故。利用高压一相接地时在线路中产生零序电压这一特性来迅速判断和切除接地的用电设备，可以保证各项施工的顺利进行。     

α-Fe_2O_3(SO_4~(2-),Sn)气敏电阻的温度响应特性

在气敏温度区域内研究了α-Fe_2O_3(SO_4~(2-),Sn)材料的电阻-温度特性,认为表面结构的变化导致温度特性出现峰值并呈现气敏性。可利用空气中电阻温度特性提供的信息改性或发现新的气敏材料。     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Study on ASTM E399 and ASTM E1921 standards

Costs of ASTM E399 and ASTM E1921 tests, which were developed to determine the fracture toughness (K_Ic) and the ductile–brittle transition temperature of ferritic steels, respectively, are considered high and the procedures are also very complicated. In this study, a method, which is more cost‐effective and easier to carry out, is proposed.     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.