A method to estimate entropies and heat capacities applied to alkali oxides

We present a method that is useful in the estimate and assessment of heat capacity data. The approach is based on an analysis of the logarithmic average of the phonon frequencies. In this quantity, that may be easily derived from experimental data on the vibrational entropy, the influence of atomic masses can be exactly accounted for even in polyatomic solids. Our method is applied to Li₂O, Na₂O, K₂O, Rb₂O, and Cs₂O. In particular, literature data for K₂O are critically examined.     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

α-Fe_2O_3(SO_4~(2-),Sn)气敏电阻的温度响应特性

在气敏温度区域内研究了α-Fe_2O_3(SO_4~(2-),Sn)材料的电阻-温度特性,认为表面结构的变化导致温度特性出现峰值并呈现气敏性。可利用空气中电阻温度特性提供的信息改性或发现新的气敏材料。     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Study on ASTM E399 and ASTM E1921 standards

Costs of ASTM E399 and ASTM E1921 tests, which were developed to determine the fracture toughness (K_Ic) and the ductile–brittle transition temperature of ferritic steels, respectively, are considered high and the procedures are also very complicated. In this study, a method, which is more cost‐effective and easier to carry out, is proposed.     

Effect of temperature on methyl radical generation over Sr/La2O3 catalysts

The role of gas phase CH₃ radicals in the oxidative coupling of CH₄ over 1 wt% Sr/La₂O₃ is supported by the observations that (i) this is a very effective catalyst for the generation of CH₃ · radicals and (ii) the concentration of CH₃ · radicals increases with temperature over the range of 450 °C–800 °C.     

A new method for the determination of wax precipitation from non-diluted crude oils by fractional precipitation

Wax precipitation is one of the most important flow assurance problems. Unfortunately, experimental data are very scarce to confirm existing models for prediction of such precipitation problem. This work reports a new experimental method. Multistage fractional wax precipitation was carried out by decreasing the temperature of crude oil. No solvent dilution was used, so the effect of solvent on temperature wax precipitation was avoided. The reproducibility of the method was tested with comparable results. The precipitation curve and the wax appearance temperature were obtained for two crude oils with different chemical nature using the reported method.