Characterization of Austempered Ductile Iron Through Barkhausen Noise Measurements

The outstanding mechanical properties of austempered ductile irons (ADI) are linked to the microstructure of the matrix obtained by subjecting a ductile iron with an appropriate composition to a heat treatment called austempering. Then the microstructure of the matrix consists of bainitic ferrite with different volume fractions of retained austenite. The aim of this work is to use the magnetic Barkhausen noise (MBN) as a nondestructive method for characterizing the microstructure of ADI. First, it is shown that the amplitude and position of the peak-shaped MBN response is quite sensitive to the microstructure of the matrix of ductile irons. Thus each type of constituent (equiaxial ferrite, pearlite, martensite or bainite) exhibits a typical response and, in turn, it can be identified from the MBN response. Furthermore, a good correlation is found between MBN signal parameters and ADI heat treatment parameters, indicating that MBN is also quite sensitive to fine evolutions of the microstructure of ADI. MBN peak position is especially sensitive to the type of bainite, whereas peak amplitude is linked to the progress of the bainite reaction. Hence MBN measurements appear to be a powerful tool to assess some important microstructural features of ADI castings.     

Damage Development in Gray Cast Iron under Static Deformation

The authors discuss the results of experimental investigation of structural degradation of gray cast iron at various stages of static tensile deformation. Analysis of the deformation process has revealed that damageability of a material under loading can be assessed by both a special strain parameter and scatter of hardness characteristics or a ratio of the modulus deviation to the current value of the elastic modulus. A correlation between these parameters has been established.     

废钢铁代用品

优质钢材的冶炼和高水平操作指标的获得需要优良的原料作保证。直接还原铁，碳化铁和脱碳粒铁作为废钢铁代用品，已显示出其价格和品质上的优越性，并弥补了废铁数量的不足，但因其各有自身的特点，故研究其理化性质和使用性能，将为大规模生产和使用创造必要的条件。     

喷射轧制Fe-4.5%Si硅钢片的组织和性能

采用喷射成形和轧制工艺制备了厚度为0.5mm的Fe-4.5%Si高硅钢片，并对其密度、显微组织和电磁性能进行了测试分析，研究结果表明：在最佳的喷射成形和轧制工艺条件下，所制备硅钢片的磁感应强度B25为1.544T、B50为1.641T；铁损P1050为1.437W/kg、P1550为3.43W/kg，说明喷射成形轧制技术可以制备出高磁感应强度、低铁损的高硅钢片。     

共晶碳化物团球化对铸铁激光熔敷层抗裂性的影响

为提高铸铁表面大面积激光熔敷层抗裂性问题，通过冶金因元素控制熔敷层组织形态在熔敷材料中加入碱金属元素钾，研究了在激光快速加热条件下钾对铸铁激光熔敷层组织团球化的影响，进而分析了该球状组织对熔敷层抗裂性的影响，结果表明随熔敷金属内钾含量增多熔敷层内共晶碳化物组织呈球状及孤岛状，这种组织明显提高了熔敷层抗裂性，此外大量的渗碳体组织确保了熔敷层具有较高的耐磨性；获得了无裂纹的大面积搭接熔敷层，其对应合金系统为Fe-C-Si-Ni-K。     

高铬锰白口铸铁的软化处理

研究了 4种退火工艺对高铬锰白口铸铁组织和硬度的影响规律。结果表明 ,采用 85 0℃保温 4h ,随后于 72 0℃保温 6h退火工艺 ,硬度最低为 36～ 38HRC ,机加工性能最好。     

首钢烧结配加扬地粉试验研究

介绍了首钢原料条件下配加扬地粉对烧结生产影响的实验室研究.随着扬地粉配入量的增加,烧结矿转鼓强度、成品率改善,燃耗有少量上升,利用系数增加,低温还原粉化指数变差.研究结果表明:在首钢目前条件下,配入10%～20%的扬地粉是可行的.二烧车间进行了扬地粉工业试验,其最高配比达到30%,工业试验时烧结各项指标变化与实验室试验结果基本一致.     

铁素体球墨铸铁与20钢的闪光对焊

试验使用铁素体球墨铸铁和20钢的实心棒料进行了闪光对焊，通过改变次级电压4～8级，通电时间3～5s，观察其焊接接头组织的变化并测定其抗拉强度。结果表明，接头由三个区组成；当通电时间一定时，抗拉强度随次级电压的升高先减小后增大；当次级电压一定时，抗拉强度随通电时间的增加而增大。在次级电压为8级、通电时间为5s时，抗拉强度达最大值，为370．8MPa，是20钢母材的90.4％，是球墨铸铁母材的83.7％。