垂直井两相流动生产测井解释滑动模型

在两相流动模拟实验数据分析的基础上 ,提出油水两相和气液两相流动的滑脱速度的实验关系 ,进而确定垂直井两相流动生产测井解释的滑动模型。现场实际测井资料处理结果表明该模型有很好的应用效果     

水解母液生产葡萄糖酸钙新工艺

葡萄糖酸钙的生产一般是以淀粉为原料经液化、糖化、发酵、中和、精制、结晶、干燥制得的。而以母液为原料，其原料成本低，工艺流程短，减少了营养元素的添加，大幅度地降低了生产成本，值得推广。     

Simultaneous HPLC quantification of total cholesterol,tocopherols and β-carotene in Barrosã-PDO veal

A simple, rapid and sensitive procedure for the simultaneous determination of total cholesterol, tocopherols and β-carotene in meat is described. The method involves a direct saponification of the meat, a single n-hexane extraction and the analysis of the extracted compounds by normal-phase HPLC, using fluorescence (tocopherols) and UV–Vis photodiode array (cholesterol and β-carotene) detections in tandem. Rates of recovery of spiked meat samples were 93% for cholesterol, 83–86% for (α-, β- and -γ) tocopherols and 89% for β-carotene. Repeatabilities were high (CV < 6%) for all determined compounds, except for δ-tocopherol. This tocopherol, which is not usually present in meat, showed a much lower recovery percentage (73%) and repeatability (12.8%). This methodology was applied for the quantification of total cholesterol, tocopherols and β-carotene in three muscles (longissimus thoracis, longissimus lumborum and semitendinosus) of the Portuguese traditional Barrosã-PDO veal, obtained from autochthonous calves fed extensively during summer (with the least abundant green pastures) and slaughtered in early autumn (October). Barrosã-PDO veal showed median contents of total cholesterol (0.50–0.56 mg/g) and, depending on the analysed muscle, moderate to high contents of α-tocopherol (3.3–3.9 μg/g) and β-carotene (0.07–0.09 μg/g), suggesting an high sensorial and hygienic quality.     

Negative effect of [bmim][PF6] on the catalytic activity of alcohol dehydrogenase: mechanism and prevention

BACKGROUND: [bmim][PF₆] is a hydrophobic ionic liquid which could be considered as an environmentally friendly solvent for biocatalysis. In pure [bmim][PF₆], however, alcohol dehydrogenase from yeast (YADH) has no catalytic activity. The aim of the present work was (1) to quantitatively study the negative effect of [bmim][PF₆] on the catalytic activity of YADH and the related mechanism and (2) to made an attempt to lessen the negative effect of [bmim][PF₆] on YADH by microemulsifying [bmim][PF₆]. RESULTS: The activity of YADH in the homogeneous solution formed by H₂O, CH₃CH₂OH and [bmim][PF₆] decreased rapidly with the increase of the molar fraction of [bmim][PF₆]. The inhibitory effect of [bmim][PF₆] on YADH was probably caused by the competition of the imidazole group of [bmim][PF₆] with the coenzyme NAD⁺ for the binding sites on YADH. In a water‐in‐[bmim][PF₆] microemulsion, YADH was catalytically active due to the formation of the interfacial membrane of the nonionic surfactant TritonX‐100, which separated YADH from [bmim][PF₆] and avoided the direct inactivation of [bmim][PF₆] on YADH. Under optimal conditions, the activity of YADH was as high as 51 µmol L^?1 min^?1. CONCLUSION: [bmim][PF₆] was an inhibitor of YADH and its negative effect on YADH could be lessened by its microemulsification. Copyright © 2008 Society of Chemical Industry     

Effect of spray nozzle design on liquid-solid contact in fluidized beds

In industrial fluid cokers the feedstock, consisting of heavy bituminous hydrocarbons, is atomized with steam and injected into a hot fluidized bed of coke. Good and uniform contact of the liquid droplets with the solid particles is required to provide heat for the cracking reactions while minimizing mass transfer effects. Experiments in a pilot plant coker have suggested that the initial particle/liquid mixing, in the spray jet, is rather poor. Experiments in a X-ray scanner showed that liquid droplets and entrained particles accumulate just below the tip of the jet plume to form agglomerates.An experimental technique was used to quantitatively determine the quality of mixing with a variety of nozzle configurations including several novel designs. By improving spray stability, redistributing liquid droplets to the solids-rich region of the jet and increasing the surface area of the gas-liquid jet-fluidized bed interface, liquid/solid contact is improved.     

Viscoelastic properties of polyarylene ether nitriles/thermotropic liquid crystalline polymer blend

Polyarylene ether nitriles (PEN)/thermotropic liquid crystalline polymer (TLCP) blend was prepared via melt mixing. The immiscible phase morphologies, linear and nonlinear, as well as transient viscoelastic properties of the blend were studied using SEM, rheometer, and DMA. The linear dynamic viscoelastic behavior of the blend shows temperature dependence due to further evolution of the immiscible morphology and, as a result, the principle of time‐temperature superposition (TTS) is invalid. In the steady shear flow, the discrete TLCP phase is difficult to be broken up because of the high viscosity ratio of the blend systems, while is easy to be coarsened and followed by elongation, and finally, to form fibrous morphology at high TLCP content and high shear level. During this morphological evolution process, the transient stress response presents step increase and nonzero residual relaxation behavior, leading to increase of the dynamic viscoelastic responses after steady preshear. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Semiflexible random thermotropic copolymers from 8‐(3‐hydroxy phenyl) octanoic acid and 3‐chloro‐4‐hydroxy benzoic acid/3,5‐dibromo‐4‐hydroxy benzoic acid

Two series of semiflexible random thermotropic copolymers containing 8‐(3‐hydroxy phenyl) octanoic acid (HPOA) with either 3‐chloro‐4‐hydroxy benzoic acid or 3,5‐dibromo‐4‐hydroxy benzoic acid were prepared by melt polycondensation techniques. The copolyesters were characterized with Fourier transform infrared spectroscopy, dilute solution viscometry, hot‐stage polarized light microscopy, differential scanning calorimetry, thermogravimetric analysis, and wide‐angle X‐ray diffraction. Studies revealed that the amount of HPOA as a disruptor incorporated into the backbone of substituted 4‐hydroxy benzoic acids had a detrimental effect on the liquid‐crystalline behavior. Mesophase‐transition temperatures were observed between 210 and 250°C, and the optical textures were of typical nematic phases. The degree of crystallinity decreased with an increase in the HPOA content. The thermal stability of the copolymers was in the range of 310–370°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

凸轮逆序测量方法

目前各杂志所发表的关于凸轮测量的文章，所讨论的均是凸轮的顺序测量方法，有关凸轮的逆序测量(反求工程)方法，尚未见于文字。本文将对凸轮的逆序测量方法进行探讨。     

连铸转炉钢包电力牵引车的研制

论述研制连铸转炉钢包牵引车的目的、意义、方案的选择及设计计算校核,对技术要点作出了明确阐述.     

Techniques and Apparatus for Measuring Rotational Core Losses of Soft Magnetic Materials

In many situations such as the cores of a rotating electrical machine and the T joints of a multiphase transformer, the local flux density varies with time in terms of both magnitude and direction, i.e. the flux density vector is rotating. Therefore, the magnetic properties of the core materials under the rotating flux density vector excitation should be properly measured, modeled and applied in the design and analysis of these electromagnetic devices. This paper presents an extensive review on the development of techniques and apparatus for measuring the rotational core losses of soft magnetic materials based on the experiences of various researchers in the last hundred years.