陶瓷表面化学镀的前处理工艺新进展

综述了非金属表面化学镀前处理工艺的现状和发展，对陶瓷化学镀的粗化和活化工艺的新进展进行了评述，侧重讨论了离子型、胶体钯型、浆料型、分子自组装吸附钯型、贱金属型活化工艺特点和进展，并展望了今后发展方向。     

一种基于混沌同步的噪音衰减算法

论文提出了一种混沌通信系统的噪音衰减算法,该算法利用混沌同步现象在接收端获得正确的噪音估计值,从而从接收信号中滤除噪音恢复出正确的信号。通过数值仿真试验表明该方法是可行的。     

柳钢新建氧化球团工程的设计特点

介绍了柳钢新建120万t／a链篦机-回转窑氧化球团工程的主要设计特点。该工程是我国第一条自行设计、设备国产化和采用清洁气体能源的链篦机-回转窑生产线。它的顺利投产，标志着我国炼铁炉料生产技术有了一个新的进步。     

Optimal Control of the Primary Drying Stage of Freeze Drying of Solutions in Vials Using Variational Calculus

The problem of operating freeze drying of pharmaceutical products in vials placed in trays of a freeze dryer to remove free water (in frozen state) at a minimum time was formulated as an optimal control problem. Two different types of freeze dryer designs were considered. In type I freeze dryer design, upper and lower plate temperatures were controlled together, while in type II freeze dryer design, upper and lower plate temperatures were controlled independently. The heat input to the material being dried and the drying chamber pressure were considered as control variables. Constraints were placed on the system state variables by the melting and scorch temperatures during primary drying stage. Necessary conditions of optimality for the primary drying stage of freeze drying process in vials are derived and presented. Furthermore, an approach for constructing the optimal control policies that would minimize the drying time for the primary drying stage was given. In order to analyze optimal control policy for the primary drying stage of the freeze-drying process in vials, a rigorous multi-dimensional unsteady state mathematical model was used. The theoretical approach presented in this work was applied in the freeze drying of skim milk. Significant reductions in the drying times of primary drying stage of freeze drying process in vials were obtained, as compared to the drying times obtained from conventional operational policies.     

Cu-Mg/Al_2O_3催化乙醇和乙二胺合成N-乙基乙二胺

在固定床反应器内,乙醇和乙二胺经分子间催化胺化反应合成了N-乙基乙二胺(NEED),考察了一系列铜系催化剂的活性,并筛选出催化性能较好的Cu-Mg/A l2O3催化剂;通过X射线衍射和透射扫描电子显微镜方法表征了助剂Mg对Cu/A l2O3催化剂的改性作用;考察了助催化剂Mg含量、反应温度、反应压力、进料量和乙二胺含量等对Cu-Mg/A l2O3催化剂性能的影响。实验结果表明,Cu-Mg/A l2O3催化剂具有很好的活性和选择性;在200℃、3.0MPa、质量分数20%的乙二胺乙醇溶液、进料量1.0mL/m in的条件下,乙二胺的转化率为71.56%,产物NEED的选择性和收率分别为92.62%和69.86%;经过20 d的连续使用表明,Cu-Mg/A l2O3催化剂具有良好的稳定性。     

井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

地震平衡技术及其在地震反演中的应用

地震平衡技术是一种在地震反演中改善井震关系的新技术。它通过单井对比、空间分形建模以及平衡处理的手段 ,克服地震反演中子波空变的影响 ,使得经过地震平衡技术处理的地震剖面井震关系得到较好改善 ,从而可以用统一的子波对研究区的地震资料进行反演     

基于高速分散的烟火药剂制备工艺

探索高速分散的烟火药剂制备工艺，分析了高速分散制备工艺中的安全性。在实际应用中，此种工艺所制备的烟火药剂有燃烧精度高的优点。     

Use of X-ray computed microtomography to understand why gels reduce relative permeability to water more than that to oil

X-ray computed microtomography (XMT) was used to investigate why gels reduce relative permeability to water more than that to oil in strongly water-wet Berea sandstone. XMT allows saturation differences to be monitored for individual pores during various stages of oil, water, and gelant flooding. The method also characterizes distributions of pore size, aspect ratio, and coordination number for the porous media. We studied a Cr(III) acetate–HPAM gel that reduced permeability to water (at S_or) by a factor 80–90 times more than that to oil (at S_wr). In Berea, the gel caused disproportionate permeability reduction by trapping substantial volumes of oil that remained immobile during water flooding (i.e., 43.5% S_or before gel placement versus 78.7% S_or after gel placement). With this high trapped oil saturation, water was forced to flow through narrow films, through the smallest pores, and through the gel itself. In contrast, during oil flooding, oil pathways remained relatively free from constriction by the gel.     

Quality Control for Scalable Media Processing Applications

Many media processing applications create a load that varies significantly over time. Hence, if such an application is assigned a lower processing-time budget than needed in its worst-case load situation, deadline misses are likely to occur. This problem can be dealt with by designing media processing applications in a scalable fashion. A scalable media processing application can run in multiple qualities, leading to correspondingly different resource demands. The problem we consider is to find an accompanying quality control strategy, which minimizes both the number of deadline misses and the number of quality changes, while maximizing the quality of processing. We present an initial approach to the above problem by modeling it as a Markov decision process (MDP). Our model is based on measuring relative progress at milestones. Solving the MDP results in a quality control strategy that can be applied during runtime with only little overhead. We evaluate our approach by means of a practical example, which concerns a scalable MPEG-2 decoder.