实体造型中的几何约束

实体造型是一个基于约束的过程，完成从功能约束到几何约束、再到代数约束的转化而得到实体模型。本文讨论了几何约束的层次性及其表示，并且对几何约束同设计意图的关系进行了研究，提出了基于ＣＳＧ／ＧＣＧ／Ｂ－ｒｅｐ的模型表示。     

A method of identifying latent human errors in work systems

Work system improvements are implemented in various manufacturing processes to prevent problems caused by human errors. However, they are almost always applied to problems which have already occurred. This paper examines a method of identifying latent human errors existing within the work systems beforehand. A procedure for applying failure mode and effect analysis to this identification problem was defined based on over 1000 empirical errors: a work system decomposition criterion and fundamental error modes for listing latent human errors, and then applied to three practical manufacturing processes in order to evaluate its effectiveness.     

Mixed Mode VLSI Implementation of a Neural Associative Memory

A mixed mode digital/analog special purpose VLSI hardware implementation of an associative memory with neural architecture is presented. The memory concept is based on a matrix architecture with binary storage elements holding the connection weights. To enhance the processing speed analog circuit techniques are applied to implement the algorithm for the association. To keep the memory density as high as possible two design strategies are considered. First, the number of transistors per storage element is kept to a minimum. In this paper a circuit technique that uses a single 6-transistor cell for weight storage and analog signal processing is proposed. Second, the device precision has been chosen to a moderate level to save area as much as possible. Since device mismatch limits the performance of analog circuits, the impact of device precision on the circuit performance is explicitly discussed. It is shown that the device precision limits the number of rows activated in parallel. Since the input vector as well as the output vector are considered to be sparsely coded it is concluded, that even for large matrices the proposed circuit technique is appropriate and ultra large scale integration with a large number of connection weights is feasible.     

A Built-in Self-Test Scheme with Diagnostics Support for Embedded SRAM

In this paper we propose a novel built-in self-test (BIST) design for embedded SRAM cores. Our contribution includes a compact and efficient BIST circuit with diagnosis support and an automatic diagnostic system. The diagnosis module of our BIST circuit can capture the error syndromes as well as fault locations for the purposes of repair and fault/failure analysis. In addition, our design provides programmability for custom March algorithms with lower hardware cost. The combination of the on-line programming mode and diagnostic system dramatically reduces the effort in design debugging and yield enhancement. We have designed and implemented test chips with our BIST design. Experimental results show that the area overhead of the proposed BIST design is only 2.4% for a 128 KB SRAM, and 0.65% for a 2 MB one.     

MB8镁合金薄板的搅拌摩擦焊

针对我国航空航天工业常用的MB8镁合金。采用搅拌摩擦焊工艺进行焊接，对其焊缝的成形特点、组织特征和力学性能进行分析。结果表明，采用搅拌摩擦焊焊接镁合金效果良好。     

Photo-Fenton removal of water-soluble polymers

This paper presents the results of experiments carried out in a laboratory-scale photochemical reactor on the photodegradation of different polymers in aqueous solutions by the photo-Fenton process. Solutions of three polymers, polyethyleneglicol (PEG), polyacrylamide (PAM), and polyvinylpyrrolidone (PVP), were tested under different conditions. The reaction progress was evaluated by sampling and analyzing the total organic carbon concentration in solution (TOC) along the reaction time. The behavior of the different polymers is discussed, based on the evolution of the TOC–time curves. Under specific reaction conditions, the formation and coalescence of solid particles was visually observed. Solids formation occurred simultaneously to a sharp decrease in the TOC of the liquid phase. This may be favorable for the treatment of industrial wastewater containing polymers, since the photodegradation process can be coupled with solid separation systems, which may reduce the treatment cost.     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

企业以顾客为中心的营销策略过程研究

试图构建企业以顾客为中心的营销策略过程的一般模型，并利用已有的研究成果对其构成要素进行了深入分析．在此基础上，对此模型所形成的企业营销策略循环进行分类分析，并以实例说明它们所代表的现实意义，从而为企业的决策提供帮助．     

Phase behavior in liquid crystallization for diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components

Phase behavior in liquid crystallization was studied for a series of liquid crystalline (LC) diblock copolymers consisting of rubbery amorphous and side-chain liquid crystalline components, poly(n-butyl acrylate) (PBA) and poly[11-(4′-cyanophenyl-4″-phenoxy)undecyl acrylate] (PLC), respectively, using a time-resolved small-angle X-ray scattering (SAXS) techniques, DSC and polarized optical microscopy (POM). The block copolymers used had three kinds of copolymer compositions, 44, 20 and 15 wt% of PLC compositions (BLC44, BLC20 and BLC15, respectively). BLC44 showed a smectic liquid crystalline structure. In the process of liquid crystallization for BLC44, the SAXS peak due to the microphase separation structure existing before liquid crystallization was changed continuously to be at a smaller angular side, and at almost the same time, a new peak appeared at a further smaller angular side and developed. The former peak disappeared with the development of liquid crystallization. The behavior of these SAXS peaks suggests that the microphase separation structure was changed discretely at the transition from isotropic to smectic and that two phases coexist in the early stage of the liquid crystallization. The coexistence of two peaks in the early stage of the liquid crystallization corresponded to the POM observation. In the isotropization process, coexistence of two phases was not observed. For BLC20 exhibiting a cylindrical structure in both isotropic and liquid crystalline states, the liquid crystalline structure was not smectic but probably nematic, and the spacing was changed continuously in liquid crystallization. No liquid crystallization was observed in SAXS, POM and DSC for BLC15. The orientation of smectic layers within lamellar domains was investigated using 2D-SAXS images. The smectic layer was aligned perpendicularly to the lamellar interface.