光测遥测数据联合计算速度的方法

提出了利用遥测的过载、俯仰角信息和光测的坐标联合计算弹道关机段速度的方法，从遥测结果的系统误差、随机误差和数值积分的截断误差三万面对剩余误差的影响进行了精度分析，并给出了速度精度的算法。     

Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

钢板侵彻过载的三维数值模拟

利用LS—DYNA有限元程序，用弹塑性模型建立材料模型，对高速弹丸侵彻均质钢板问题进行了数值模拟，并与测试结果进行了比较，说明了有限元分析的有效性，为引信设计提供参考。     

A parametric interpolator with confined chord errors, acceleration and deceleration for NC machining

Parametric interpolation has many advantages over linear interpolation in machining curves. Real time parametric interpolation research so far has addressed achieving a uniform feed rate, confined chord errors and jerk limited trajectory planning. However, simultaneous consideration of confined chord errors that respect the acceleration and deceleration capabilities of the machine has not been attempted. In this paper, the offline detection of feed rate sensitive corners is proposed. The velocity profile in these zones is planned so that chord errors are satisfied while simultaneously accommodating the machine's acceleration and deceleration limits. Outside the zone of the feed rate sensitive corners, the feed rate is planned using the Taylor approximation. Simulation results indicate that the offline detection of feed rate sensitive corners improves parametric interpolation. For real time interpolation, the parametric curve information can be augmented with the detected feed rate sensitive corners that are stored in 2×2 matrices.     

Boundary Procedures for Summation-by-Parts Operators

Four different methods of imposing boundary conditions for the linear advection-diffusion equation and a linear hyperbolic system are considered. The methods are analyzed using the energy method and the Laplace transform technique. Numerical calculations are done, considering in particular the case when the initial data and boundary data are inconsistent.     

台湾东北近海冬季上升流的数值模拟研究

该文利用已发展的三维斜压数值模式,模拟了冬季台湾东北近海上升流结构和空间分布。结果表明,冬季黑潮水在台湾东北海域向陆架入侵的同时,还伴随着强烈的上升流运动;从台湾北部的基隆近海经台湾东北角近海到宜兰海湾,存在3个上升流中心,量级为30~40×10-3cm s-1左右;在台湾东北近海最大上升流流速位于海底,约50×10-3cm s-1量级,并可直达海面。     

火灾中受保护钢构件的温度数值计算

利用传热学原理，考虑保护层表面热阻和保护层厚度内温度的非线性变化，建立受保护钢构件在火灾条件下瞬态导热微分方程，并计算其截面温度。     

改进的BP神经网络在大坝安全监控中的应用

针对经典BP神经网络运行中存在的缺陷，提出了改进的BP神经网络，不仅解决了经典BP网络易陷入局部最小的弊端，而且应用的0.618分割选取法能使网络快速找到较优隐含层节点数，初始权值的自相关修正进一步提高了网络的稳定性。实际应用证明，改进的BP神经网络有效提高了网络质量，适合大型网络的构建与训练。     

单孔护壁爆破数值模拟

运用LS-DYNA软件对单孔护壁爆破和切缝药包爆破进行了三维数值模拟,结果显示,由于PVC-U套管的存在,作用于孔壁的爆炸应力波峰值被显著削弱,降低率达到30%～46%,并推迟了其到达保留岩体孔壁时间.与传统的切缝药包爆破相比,保留岩体损伤更小.     

数控母排冲孔机液压系统

介绍了数控母排冲孔机液压系统工作原理及其组成，设计了双泵供油回路、压力控制的差动快进转慢进回路及过载、过热、污染堵塞报警系统。