Dynamic modes of Ti combustion in a coflow of N<Subscript>2</Subscript>-Ar mixture

Combustion of bulk density Ti powder (containing 20 wt % TiN as a diluent) in a coflow of N₂-Ar mixture was investigated upon variation in the nitrogen content of the gaseous mixture. The obtained data are believed to open up new horizons for fabrication of layered and composite ceramics by infiltration-mediated combustion.      

注射成形Fe-50%Ni软磁合金的研究

Fe-50 %Ni合金是一种典型的高磁导率和低矫顽力的软磁材料,有着广阔的应用前景.本次实验采用注射成形方法制取Fe-50 %Ni,研究了在注射成形工艺中烧结工艺对最终产品性能及微观组织的影响,并分析了影响产品磁性能的一些主要因素.实验表明,烧结温度的提高和烧结时间的延长能够较好改善产品的力学性能;密度是影响产品磁性能的主要因素,杂质(主要指(C、O、N)的含量和晶粒尺寸对剩磁、磁导率和矫顽力也有较大的影响;通过注射成形方法制取的Fe-50 %Ni,其性能要优于采用传统粉末冶金方法制造的Fe-50 %Ni.     

Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

济钢高炉喷煤数学模型的研究与应用

基于湍流两相流理论建立了高炉喷煤两相流动及传质三维数学模型。采用该模型指导高炉生产 ,高炉利用系数由2 .7t/(m3.d)提高到 3 .0 t/(m3.d)以上 ,焦比由 460 kg/t降到 40 0 kg/t,煤比达到 10 0 kg/t,提高了高炉的各项经济技术指标。     

籼米淀粉超微粉体的制备及其性质

研究了籼米淀粉超微粉体的一种新的制备方法 ,通过正交实验确定了酶处理淀粉的最佳条件 ,考察了淀粉的溶解度和膨润力。结果表明 ,酶处理淀粉的最佳工艺参数为 :水解温度４５℃ ,时间为２５ｈ ,酶用量为水解淀粉的４５%。随着粒径的减小 ,淀粉的溶解度增大 ,膨润力下降。     

化学还原法制备纳米铜粉的研究

本文采用KBH4在液相中化学还原CuSO4,并加入KOH和络合剂EDTA ,制得了纳米级的纯净的铜粉 ,通过调整反应物的浓度 ,可以消除Cu2 O等杂质。制备的纳米铜粉还存在一定程度的团聚 ,需试验加入分散剂来改善。     

高合金钢铸造用涂料的试制与开发

介绍了炉爪用合金钢1Cr25Ni20Si2Re,导板用合金钢2Cr32Ni5采用串箱铸造过程中，有关镁砂粉涂料和石英粉涂料的试制。结果表明：镁砂粉涂料为不透气涂料，不太适用，而合理配方的石英粉涂料使用性能良好。     

超细粉碎技术现状及发展趋势

综述了国内外超细粉碎技术及设备的现状、进展,指出了其发展趋势,从工作原理、结构特点等方面详细介绍了超细粉碎典型设备,同时又指出了近年来国内外在此领域中的新进展,基于现存问题指出了今后超细粉碎研究的方向。     

注聚采出水分离用动态水力旋流器特性研究

原有的地面工艺和设备已不能满足聚合物驱采出水分离的要求。采用自行研制的动态水力旋流器，在增压与不增压两种工艺流程下，分别进行了流量和转数对分离效率的影响、转数与压力降的关系，以及入口压力与处理量的关系等项试验研究。试验结果表明，与静态水力旋流器相比，动态水力旋流器的分离效率明显提高，一般可提高10％左右；压力损失显著降低，约可减少0．1MPa，足见可在低压下工作，易于实现无泵运行；无泵运行明显比有泵增压运行的分离效率高，但处理量会有所降低。将动态水力旋流器应用于聚合物驱产出水的油－水分离处理是完全可行的。