电算法在液压支架受力分析中的应用

建立支架受力分析的电算设计数学模型并给出程序框图     

The effect of a solid additive on rolling fatigue life

Behaviour of a series of lubricant oils and the effect of a non stoichiometric inorganic compound, as solid extreme pressure additive, on rolling fatigue life are studied using the rolling four-ball accelerated service simulation test proposed by Barwell and Scott. The results show, in all tested cases, the remarkable efficacy of this type of additive. The Total Acidity Number (tan) was found to increase with performance time for the case of the base lubricant, while for the oils with additives, it remained at its constant low value. This led to a proposal of a possible mechanism of the additive performance in the rolling process.     

轧机主传动万向联轴器辊端接头结构探讨

分析了衬板槽平面与叉头十字轴孔轴线的相对位置对辊端接头应力的影响 ,研究了轧辊扁头与衬板之间间隙所产生的冲击和应力集中 ,讨论了辊端接头中部过渡段结构对应力分布和制造质量的影响。提出辊端接头结构设计的优化方案     

冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

Discrimination of B–C–N nanotubes through energy-filtering electron microscopy

Various multi-walled nanotubes in the B–C–N system are thoroughly investigated using a JEOL-3100FEF high-resolution field emission transmission electron microscope operating at 300 kV and equipped with an in-column built Omega filter. Spatially-resolved B, C and N elemental maps of the nanotubes are constructed. It is realized that a wide variety of tubular arrays composed of B, C and N atoms may exist in the system. Sandwich-like BN-rich and C-rich alternating tubular shells, graphitic C layers inside and outside of pure BN shells induced either by surface contamination, or electron beam irradiation, separation of C-rich and BN-rich tubes and/or BN particles within tubular bunches may take place. One should carefully take these effects into account while analyzing nanotube physical properties, e.g., electrical or optical, rather than simply rely on electron energy loss spectra typically collected from B, C and N containing nanostructures as a whole. Striking dependence of an individual nanotube electrical conductivity on tubular shell chemistry is demonstrated using I–V curve recording in an atomic force microscope.     

Removal of As(V) Ions from Solution by Akaganeite bgr-FeO(OH) Nanocrystals

The original method is developed for producing the new inorganic sorption material of akaganeite bgr-FeO(OH). The material in question is characterized relative to arsenic contained in aqua. The possibility is established for removing arsenate ions from water by contemporary physicochemical methods.     

Nucleation of branches in elastomeric polypropylene

The formation of a crosshatched morphology during crystallization of an isotactic polypropylene with low crystallinity is studied in detail. Here, a lamella seems to grow through another nearly perpendicular lamella that was crystallized before. The crystallization was observed with in situ scanning force microscopy with a temporal resolution of 3 min per image. After crystallization the volume structure was imaged by nanotomography. A detailed scheme for the nucleation of branches is proposed.     

Total simulation model of the thermo-mechanical process in shape rolling of steel rods

The production of steel reinforcing bars for civil engineering is investigated by means of FEM-simulation. An integrated system for computing appropriate thermo-mechanical parameters of the rolling process is proposed. Generalized plane strain approach and coupled thermal-mechanical solution are applied. The microstructural model combines both the effect of the recrystallization mechanisms (static, dynamic and metadynamic) upon the austenite grain forming in hot rolling and that of phase transformation upon the final microstructure. The phases are created during interrupted below the temperature of martensite transition cooling. Thus a typical industrial process for thermo-mechanical strengthening of reinforcing bars, known as Tempcor-process is considered. Computational results are validated to experimental measured mechanical properties of the steel. By means of computer simulation the system can perform different solutions, giving the possibility to obtain a reasonable choice of different thermo-mechanical rolling conditions.     

Highly oriented star-like patterns observed on GaSe epilayers grown on Si(111)

Epitaxial lamellar gallium selenide (GaSe) semiconductors have been grown on trench-patterned silicon (Si) substrates by molecular beam epitaxy. An intriguing star-like patterned morphology was identified by atomic force microscopy on these epilayers. This non-trivial feature can be correlated with the accumulation of stacking faults of two concurrent epitaxial domains around self-oriented triangular pits developed earlier on the Si(111) surface by the chemical etching. Crystallographic considerations show how the stars can be formed.