光隔离器及其相关的磁光材料

本文简要介绍了磁光隔离器的理论、结构和分类 ,并提出了该器件今后发展的几个问题 ,最后介绍了几种磁光材料     

Pad effects on material-removal rate in chemical-mechanical planarization

The role of a porous pad in controlling material-removal rate (MRR) during the chemical-mechanical planarization (CMP) process has been studied numerically. The numerical results are used to develop a phenomenological model that correlates the forces on each individual abrasive particle to the applied nominal pressure. The model provides a physical explanation for the experimentally observed domains of pressure-dependent MRR, where the pad deformation controls the load sharing between active-abrasive particles and direct pad-wafer contact. The predicted correlations between MRR and slurry characteristics, i.e., particle size and concentration, are in agreement with experimentally measured trends reported by Ouma¹ and Izumitani.²     

Ti基MnO_x型DSA析氧电极材料的性能

本文报导了新型 Ti/SnO_2+MnO_x+RuO_2/MnO_x(DSA)电极材料的各种性能,其中包括电极的导电性、表面粗糙度、电化学活性表面积、析氧阳极特性等,并用 X 射线衍射法进行了物相分析、用 SEM观察了表面形貌。确认该电极性能良好,加之成本较低,可作为酸性介质中的析氧电极材料。     

Structure and Magnetic Properties of LaCo_(13-X)M_X Intermetallic Compounds

ＳｔｒｕｃｔｕｒｅａｎｄＭａｇｎｅｔｉｃＰｒｏｐｅｒｔｉｅｓｏｆＬａＣｏ＿（１３－Ｘ）Ｍ＿ＸＩｎｔｅｒｍｅｔａｌｌｉｃＣｏｍｐｏｕｎｄｓＷＵＪｉａｎＭｉｎ；ＬＩＦｅｎｇ；ＴＡＩＬｉＣｈｉａｎｄＺＨＥＭＧＱｕｎＳｔｒｕｃｔｕｒｅａｎｄＭａｇｎｅｔｉｃＰ...     

准分子激光的应用

本文介绍了准分子激光器的基本类型、主要应用领域及其与材料相互作用的机理。对准分子激光在电子工业、生物医学和材料加工方面的一些重要应用做了比较详细的论述。     

结构振动控制中压电阻尼技术研究—压电被动阻尼技术（一）

压电阻尼技术有两种类型：压电被动阻尼技术和压电主动阻尼技术。本文对其中的压电被动阻尼技术进行了研究，结果表明：通过给压电元件并联适当的外部电路，可使压电系统具有与粘弹阻尼材料及动力吸振器相似的物理特性。合理配置电路参数，可以实现最优阻尼比。     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

T8钢—聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性，磨料磨损性及土壤的减粘降组性能，与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％－－２２．２７％。     

Thermography of aged contacts of high voltage equipment

New developments in diagnostic tools and systems are necessary for a reliable and economic evaluation of the condition of equipment in power systems. In a research project a tool for the condition of contacts of centre break disconnector, which is used under normal operation by the aid of a thermography measurement system, has been developed. In this paper, an overview about the laboratory investigation of the temperature load behaviour and the environmental influence on-site for new and aged disconnector contacts are given. A condition evaluation tool for contacts, which was the aim of the project, has been created. The basic method for the evaluation is presented, and also two additional easements for a fast identification of suspect contacts are presented. With this evaluation tool and the usage of a thermography based measuring system, a condition based maintenance strategy can be applied, whereby an early detection of damages is possible and so power quality and reliability increase.      

共聚物水凝胶的合成及其溶胀性能研究

以过氧化二苯甲酰(BPO)为引发剂，合成了N-乙烯基吡咯烷酮(NVP)-甲基丙烯酸肛羟乙酯(HEMA)-甲基丙烯酸丁酯(BMA)共聚物水凝胶，可作为软性角膜接触镜材料。探讨了不同比例的NVP、HEMA、BMA对材料溶胀性能的影响。