具有减少辨识参数的随机多变量极点配置自适应控制器

本文提出了一种新的限制输出个数减少随机多变量自适应控制中辨识参数的方法，并给出了减少辨识参数的极点配置自适应算法。虽然采用ｎ个输入１个输出的减少辨识参数的模型来设计控制器，但所提出的控制器能够保证被控系统的几个输出跟踪参考输入信号，仿真结果表明，所提出的方法是成功的。     

On the boundary-layer control through momentum injection: Studies with applications

The concept of moving surface boundary-layer control, as applied to a Joukowsky airfoil, is investigated through a planned experimental programme complemented by numerical studies. The moving surface was provided by rotating cylinders located at the leading edge and/or trailing edge as well as top surface of the airfoil. Results suggest that the concept is quite promising, leading to a substantial increase in lift and a delay in stall. Depending on the performance desired, appropriate combinations of cylinder geometry, location and speed can be selected to obtain favourable results over a wide range of angle of attack. Next, effectiveness of the concept in reducing drag of bluff bodies such as a two-dimensional flat plate at large angles of attack, rectangular prisms and three-dimensional models of trucks is assessed through an extensive wind tunnel test-programme. Results show that injection of momentum through moving surfaces, achieved here by introduction of bearing-mounted, motordriven, hollow cylinders, can significantly delay separation of the boundary-layer and reduce the pressure drag. The momentum injection procedure also proved effective in arresting wind-induced vortex resonance and galloping type of instabilities. A flow visualization study, conducted in a closed-circuit water tunnel using slit lighting and polyvinyl choride tracer particles, adds to the wind-tunnel and numerical investigations. It shows, rather dramatically, the effectiveness of the moving surface boundary-layer control (MSBC). The Sabita Chaudhury Memorial Lecture The models were fabricated in the Mechanical Engineering Workshop. The assistance of M/s E Abell, P Hurren and D Camp in the design and construction of the models is gratefully acknowledged. The investigation was supported by the Natural Sciences and Engineering Research Council of Canada, Grant No. A-2181.     

CO2 abatement by co-firing of natural gas and biomass-derived gas in a gas turbine

In this work, a possible way for partial CO₂ emissions reduction from gas turbine exhausts by co-firing with biomass is investigated. The basic principle is the recirculation of a fraction of the exhausts (still rich in oxygen) to a gasifier, in order to produce syngas to mix with natural gas fuel. As biomass is a CO₂ neutral fuel, the fraction of replaced natural gas is a measure of CO₂ removal potential of the powerplant.     

镁法海绵钛生产工艺中大型无隔板镁电解槽的节能实践

以镁法海绵钛生产工艺中大型无隔板镁电解槽的实际节能情况为例，探讨了在镁电解生产中的非生产耗电、生产耗电、漏电等因素造成的能量浪费，阐述了生产中粗镁直流电耗、电流效率、工作电压3者之间的关系，指出了影响电解槽工作电压的有关因素及降低电解槽工作电压的途径。     

浅谈降低电解槽氟化铝单耗的方法

氟化铝是电解生产中十分重要的原料，它对控制电解槽电解质温度，保持电解槽技术条件发挥着重要的作用。但随着电解生产成本的逐渐降低，氟化铝的消耗成为电解生产成本中的一项重要内容。本文就某分厂电解槽氟化铝添加的生产工艺、设备、控制以及管理等方面，提出降低氟化铝单耗的简要方法。     

铝电解槽磁流体稳定性有限元分析

本文采用有限元法求解分层磁流体小扰动方程系统特征值，研究铝电解槽稳定性。研究结果表明，在没有电磁力时，铝液表面波动（内波）是稳定的。存在电磁力时，它会激发铝液表面波动的某些低频长波分量不稳定性，高频短波不受影响。被激发的不稳定波动频率和扰动增长率与电流密度，磁感应强度垂直分量，铝电解槽长宽比，电解质和铝液的密度差，厚度等因素密切相关。减少电流密度，磁感应强度，增加电极距离和铝液厚度可以提高铝电解槽的稳定性。这对铝电解槽优化设计和在线控制有重要意义。     

An orthogonal basis for the hyperbolic hybrid polynomial space

Motivated by the wide usage of the Tchebyshev basis and Legendre basis in the algebra polynomial space, we construct an orthogonal basis with the properties of the H-Bézier basis in the hyperbolic hybrid polynomial space, which is similar to the Legendre basis and holds remarkable properties. Moreover, we derive the transformation matrices that map the H-Bézier basis and the orthogonal basis forms into each other. An example for approximating the degree reduction of the H- Bézier curves is sketched to illustrate the utility of the orthogonal basis.     

ZRS-6.72-3型电收尘器技术改造

ZRS-6．72—3型电收尘器原设计用于13．8kt／a锌冶炼烟气收尘制酸工艺中，因电收尘器使用时间长，电源控制柜故障率高和沸腾炉扩大更新，对电收尘器同步进行配套技术改造。改造为CRS-8．24—3型电收尘器后，又陆续使用了HL-Ⅲ型恒流源控制电柜，投产后的电收尘器具有收尘效率高、电场运行稳定等特点。