过氧化甲乙酮合成研究

论述了过氧化甲乙酮的合成方法，用阳离子交换树脂催化剂代替传统的无机酸催化剂。考察了离子交换树脂用量、反应温度对反应产率、活性氧含量的影响及溶剂对产品稳定性的影响。     

Peracetic acid pretreatment of sugarcane bagasse for enzymatic hydrolysis: a continued work

Previous work has shown that the enzymatic hydrolysis of sugarcane bagasse could be greatly enhanced by peracetic acid (PAA) pretreatment. There are several factors affecting the enzymatic digestibility of the biomass, including lignin and hemicelluloses content, cellulose crystallinity, acetyl group content, accessible surface area and so on. The objective of this work is to analyze the mechanism of the enhancement of enzymatic digestibility caused by PAA pretreatment. Delignification resulted in an increase of the surface area and reduction of the irreversible absorption of cellulase, which helped to increase the enzymatic digestibility. The Fourier transform infrared (FTIR) spectrum showed that the absorption peaks of aromatic skeletal vibrations were weakened or disappeared after PAA pretreatment. However, the infrared crystallization index (N.O'KI) was increased. X‐ray diffraction (XRD) analysis indicated that the crystallinity of PAA‐treated samples was increased owing to the partial removal of amorphous lignin and hemicelluloses and probable physical change of cellulose. The effect of acetyl group content on enzymatic digestibility is negligible compared with the degree of delignification and crystallinity. The results indicate that enhancement of enzymatic digestibility of sugarcane bagasse by PAA pretreatment is achieved mainly by delignification and an increase in the surface area and exposure of cellulose fibers. Copyright © 2008 Society of Chemical Industry     

The influence of raw material characteristics on the industrial pelletizing process and pellet quality

Industrial pelletizing of sawdust was carried out as a designed experiment in the factors: sawdust moisture content, fractions of fresh pine, stored pine and spruce. The process parameters and response variables were energy consumption, pellet flow rate, pellet bulk density, durability and moisture content. The final data consisted of twelve industrial scale runs. Because of the many response variables, data evaluation was by principal component analysis of a 12 × 9 data matrix. The two principal component model showed a clustering of samples, with a good reproducibility of the center points. It also showed a positive correlation of energy consumption, bulk density and durability all negatively correlated to flow rate and moisture content. The stored pine was more related to high durability and bulk density. The role of the spruce fraction was unclear. The design matrix, augmented with the process parameters was a 12 × 6 matrix. Partial least squares regression showed excellent results for pellet moisture content and bulk density. The model for durability was promising. A 12 × 21 data matrix of fatty- and resin acid concentrations measured by GC–MS showed the differences between fresh and stored pine very clearly. The influence of the spruce fraction was less clear. However, the influence of the fatty- and resin acids on the pelletizing process could not be confirmed, indicating that other differences between fresh and stored pine sawdust have to be investigated. This work shows that it is possible to design the pelletizing process for moderate energy consumption and high pellet quality.     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.     

青藏铁路西格二线混凝土冻融试验研究

由于工期的要求,青藏铁路西格增建二线必须进行冬期施工。根据工程状况,分析了混凝土受冻的破坏机理,针对施工环境及对混凝土设计强度和要求,进行了大量冻融试验分析,对引气剂、水胶比、砂率、粉煤灰掺量等原材料与混凝土含气量的关系及其混凝土搅拌温度与静停时间等对混凝土性能的影响进行了分析与技术论证,确保了该线冬期混凝土施工顺利进行。     

负载型固体碱催化合成亚苄基丙酮

研究了用固体碱 KOH/Al_2O_3催化合成苯叉丙酮,确定了合成的最佳工艺条件:n(苯甲醛)∶n(丙酮)=1∶4.催化剂用量2g,催化剂最佳负载量12mmol/g,反应温度40～45℃,反应时间为3h,产率达88%以上。     

Impact of the addition of an enzyme pool on an activated sludge system treating dairy wastewater under fat shock loads

BACKGROUND: The application of lipase‐rich enzyme pools (such as the crude solid enzymatic preparation (SEP) obtained from Penicillium restrictum solid‐state fermentation of agro‐industrial wastes) to activated sludge systems may be an effective strategy for preventing various operational problems. The continuous addition of SEP to the treatment system can become cost‐prohibitive when in situ production and/or storage are factored in. The application of SEP to high‐fat wastewater treatment would only be justified as an emergency measure, such as a sudden increase in the fat content of the bioreactor influent. Therefore, the primary objective of this work was to investigate the efficiency of a crude SEP during fat shock loads, simulated through the periodic addition of dairy industry waste containing high fat concentrations to the feed stock of an activated sludge system, operated in continuous mode. RESULTS: The test bioreactor exhibited a higher average chemical oxygen demand (COD) removal efficiency than the control bioreactor (83% for control and 90% for test) and the fat accumulation in the biological flocs of the test bioreactor was 3.2 times lower than that in the control bioreactor. Turbidity was also lower in the effluent of the test bioreactor (123 and 66 FTU in control and test, respectively) and it had a shorter recovery time between shock loads, especially when the interval between loads was shorter than one month (biweekly and weekly shock loads). CONCLUSION: The addition of SEP during fat overloads in the reactor feed maintained efficient COD removal in the test bioreactor for 270 days without any operational problems. Copyright © 2008 Society of Chemical Industry     

Boiling: Size Distribution of Bubbles as Demanded by the Principle of Maximum Information

The principle of maximum informational entropy is used to find the probability density function for the departure radius of a bubble in boiling on a solid surface. A general relation is derived, which leads to particular expressions.     

A three‐dimensional model describing stress‐temperature induced solid phase transformations: solution algorithm and boundary value problems

An always increasing knowledge on material properties as well as a progressively more sophisticated production technology make shape memory alloys (SMA) extremely interesting for the industrial world. At the same time, SMA devices are typically characterized by complex multi‐axial stress states as well as non‐homogeneous and non‐isothermal conditions both in space and time. This aspect suggests the finite element method as a useful tool to help and improve application design and realization. With this aim, we focus on a three‐dimensional macroscopic thermo‐mechanical model able to reproduce the most significant SMA features (Int. J. Numer. Methods Eng. 2002; 55 : 1255–1264), proposing a simple modification of such a model. However, the suggested modification allows the development of a time‐discrete solution algorithm, which is more effective and robust than the one previously discussed in the literature. We verify the computational tool ability to simulate realistic mechanical boundary value problems with prescribed temperature dependence, studying three SMA applications: a spring actuator, a self‐expanding stent, a coupling device for vacuum tightness. The effectiveness of the model to solve thermo‐mechanical coupled problems will be discussed in a forthcoming work. Copyright © 2004 John Wiley & Sons, Ltd.     

Review on testers for measuring flow properties of bulk solids

 The author was asked by the International Fine Particle Research Institue (IFPRI) to write a critical review on shear testers for IFPRI-members. The review was delivered to IFPRI in summer 1999. Following the contract with IFPRI it was not allowed to publish the review elsewhere for at least two years. Granular Matter invited the author to submit the review in the original form; during the refereeing process (besides other changes) it turned out that some remarks should be added here for clarification: - Since 1999, the author is not aware of a really new device for testing bulk solid properties, which could lead to a change of the general comments and conclusions provided in the review. It was argued, that the review is referring too much to the work of Jenike, while the works of Johanson and Peschl were not adequately cited. Both are excellent engineers with a lot of experience, but their basic ideas are not available in published form, and if, they are not set in relation to alternative approaches so that an objective comparison in detail would be a future research issue rather than a topic in this report. A discussion on the influence of electrostatic charges was missing. There hardly is an influence, since the particles are in continuous contact. Only with non-conducting plastic particles electrostatic charges could cause problems. But no relevant experiments and results are known. In closed systems, the effect of electric charges is thus mainly neglected, but it is clear that electrostatic forces are eminent in flows with a free surface – an issue not addressed in this review. Received: 1 November 2002