AN EXPERIMENTAL-NUMERICAL METHOD FOR MEASURING CRACK PROPAGATING VELOCITIES UNDER STRESS WAVE LOADING

An experimental-numerical method for measuring dynamic crack propagating velocities under stress wave loading is established in this paper. The experiments of the three-point bend specimen are done on the improved Hopkinson bar. Deflection of loading point, dynamic load and instantaneous crack length are measured, then crack propagating velocities are calculated. Experiments on 40Cr steel show that the results given by this method have a good agreement with that obtained by the resistance fracture gage method. Therefore this method is feasible for measuring crack propagating velocities under high loading rate and will have wide application.     

Multidisciplinary optimization of gas-quenching process

Distortion as a result of the quenching process is predominantly due to the thermal gradient and phase transformations within the component. Compared with traditional liquid quenching, the thermal boundary conditions during gas quenching are relatively simple to control. By adjusting the gas-quenching furnace pressure, the flow speed, or the spray nozzle configuration, the heat-transfer coefficients can be designed in terms of both the component geometry and the quenching time. The purpose of this research is to apply the optimization methodology to design the gas-quenching process. The design objective is to minimize the distortion caused by quenching. Constraints on the average surface hardness, and its distribution and residual stress are imposed. The heat-transfer coefficients are used as design variables. DEFORM-HT is used to predict material response during quenching. The response surface method is used to obtain the analytical models of the objective function and constraints in terms of the design variables. Once the response surfaces of the objective and constraints are obtained, they are used to search for the optimum heat-transfer coefficients. This process is then used instead of the finite-element analysis. A one-gear blank case study is used to demonstrate the optimization scheme.     

萃取预分离法分离富铕中钇矿新工艺

采用一种新的串级萃取方式--萃取预分离法分离富铕中钇矿的新工艺.原料首先流入十几的三出口预先粗分离工艺,其萃余液La～Gd(TbDy)直接流入Nd/Sm工艺;中间出口流入(Gd)Tb～HoY(Er)Gd～Dy/Ho～LuY细分离工艺;出口负载有机相(Ho)Er～LuY流入Gd～Dy/Ho～LuY的洗涤段.结果表明,新工艺的粗分离工艺将占原料约70%的La～Gd(TbDy)预分离掉,使流入Gd～Dy/Ho～LuY工艺的稀土量减少约70%;由于Gd～Dy/Ho～LuY分组的萃余液GdTbDy含Ho2O3小于0.03%,省去原工艺的GdTbDy/HoY分离;新工艺的处理能力提高30%,酸碱消耗减少20%以上,贵重稀土元素Eu和Tb的存槽量大大减少.     

溶液法制备高接枝率HDPE-g-MAH

用溶液法制备了HDPE -g -MAH,并讨论了单体、引发剂用量、反应温度、反应时间、投料方式等因素对产物接枝率的影响。     

GRAPHICAL PROCEDURE FOR REACTIVE DISTILLATION SYSTEMS

In this paper we analyze a ternary reactive distillation system, where an equilibrium chemical reaction occurs in the liquid phase. By using a set of transformed variables proposed by Barbosa el al. (1988b) and well known graphical procedures for non-reactive systems; the minimum reflux ratio, minimum number of equilibrium stages, mass and energy balances for a reactive column and flash can be easily obtained. The procedures developed in this paper are applied to ISOBUTYLENE-METHANOL-MTBE system.

The main objective in developing this model is to obtain, as much as possible, rigorous information for the analysis of one reactive distillation column in a Process Simulator with capability of handling this type of new operation.     

水性聚氨酯材料配方设计技巧

介绍了优选法的0.618法和分数法,对其进行改进创新和原理证明,并应用于生产涂料配方设计中。     

Catalytic Combustion of Methane over Rare Earth Stannate Pyrochlore

Well-defined Ln₂Sn₂O₇ powders (Ln = La, Sm and Gd) with a phase-pure pyrochlore structure were synthesized by hydrothermal reaction. The catalytic activities of Ln₂Sn₂O₇ powders for methane combustion were measured. Methane oxidation started at 500 °C and increased with oxidation temperature. Catalytic methane combustion is strongly influenced by the presence of oxygen vacancies that form by breaking Sn–O lattice bonds as the temperature increases. Addition of manganese to the rare earth pyrochlores improved methane oxidation activity. Manganese-doped samarium stannate pyrochlore (Sm₂Sn_1.8Mn_0.2O₇) shows highest the catalytic activity. Light-off and complete oxidation temperatures were measured at about 400 and 650 °C, respectively.     

粉末涂料涂装工艺(Ⅰ)

介绍了粉末涂料的几种涂装方法及其原理、特点、应用范围和进展情况，重点介绍了静电粉末涂装方法。     

Pervaporation performance analysis and prediction—using a hybrid solution-diffusion and pore-flow model

A hybrid mathematic model for pervaporation is proposed which incorporates the concepts of solution-diffusion model and pore model. The model allows performance prediction as well as the establishment of the internal concentration and pressure profiles within the membrane. The model parameters specific to the particular membrane and mixture system are determined using liquid sorption and pervaporation experimental data. The model is experimentally examined using ethanol–water mixtures and poly(dimethyl siloxane)–poly(vinyldiene fluoride) (PDMS–PVDF) composite membranes. The characteristics of flux and separation factor predicted using the model are in fair agreement with the experimental data under various feed concentrations and downstream pressures for different membrane arrangements, including single-layer, reverse single-layer and double-layer PDMS–PVDF composite membranes. Internal profiles of pressure, concentration and component mole fraction can be established using the model. Concentration polarization phenomena for ethanol and water are located at membrane interfaces and vapor–liquid interfaces, respectively. Performances of several different membrane designs are compared using the model.     

熔体塔式造粒法生产尿基复混肥

化肥企业生产尿基复混肥对于农业科学施肥、提高肥料利用率、避免环境污染及促进企业产品结构调整都具有十分重要的意义。熔体塔式造粒法生产尿基复混肥较之其它方法优越性更为显著,笔者简要介绍该法的生产机理、工艺流程、技术特点、国内现状及产品市场前景等方面的一些情况。