车床静刚度计算机测试系统研制

在分析了车床的结构特点和车削工艺系统的受力情况和借鉴传统车床静刚度仪优点的基础上，研制了一套基于计算机控制的车床静刚度测试系统。系统由计算机作为信号检测、数据处理和控制核心，并配以精密位移传感器、压力传感器和步进电机及其驱动器等。实现了自动加载、卸载，采样，数据处理，直接绘制、显示和打印刚度曲线等功能。系统的成功研制为车床静刚度的测试提供了一种先进手段。实测结果表明，该系统具有自动化程度高、测试效率高、精度高、可靠性高、测试性能稳定的优点。     

改善操作延长转化炉炉管寿命

分析转化炉炉管不正常原因及对炉管造成的危害，确定通过改善工艺操作来延长转化炉炉管寿命，实践证明效果明显。     

百菌清及其三氟衍生物对番茄早疫病菌的室内抑菌活性比较

采用生长速率法测定了不同浓度的百菌清及其三氟衍生物对番茄早疫病菌Alternaria solani(Ell,et Mart.)Jones es Gmut的室内杀菌毒力。试验结果表明，百菌清及其三氟衍生物的ED50值分别为6089．89mg／L和156．43mg/L。，前者是后者的38．93倍。百菌清三氟衍生物的毒力明显高于百菌清。     

一种新的感度试验与分析方法

介绍了一种新的感度试验设计与分析方法，即Ｎｅｙｅｒ法。它利用最大似然估计来选择下一个试验水平，利用似然比试验可计算任意置信区间，并以Ｃｒａｍｅｒ－Ｒａｏ理论为基础，可以分析所有感度试验结果。     

GRIP管混凝土组合结构压弯构件非线性全过程分析

本文应用细观力学、经典层板理论、平截面假定、FRP约束混凝土本构模型及数值积分对GFRP管混凝土组合结构压弯构件进行了非线性全过程分析。通过理论计算发现GFRP管混凝土组合结构能有效地提高构件的承载力，且构件具有良好的变形能力。FRP壳体参与承载且有效地约束混凝土的变形，显著提高核心混凝土强度和变形能力。文中讨论了轴压比、长细比、径厚比、混凝土强度等级、纵筋配筋率、铺层角变化对极限水平荷载和极限水平位移的影响，从而得到了一些有益的结论。     

Measurement of Adhesive Bond Properties Including Damage by Dynamic Mechanical Thermal Analysis of a Beam Specimen

A method to obtain mechanical properties using a bonded (double) cantilever beam (or three point bend) specimen loaded in a manner to produce pure shear in the adhesive layer is reviewed. A revised mathematical solution which allows for easier interpretation of optimum beam dimensions to the one originally developed by Moussiaux, Cardon and Brinson for the static case is presented. An extension of this solution for a fixed/fixed viscoelastic beam under steady state oscillations developed by Li, Dickie and Morman is also discussed. Previous results using a vibrating beam to determine the complex viscoelastic properties of a bonded beam are reviewed. These results demonstrate conclusively that dynamic mechanical thermal analysis (DMTA) measurements discriminate differences in surface treatments and various environmental conditions. New measurements are presented that indicate the DMTA procedure can be used to quantify damage simulated by imbedded flaws in beams. The procedure is also shown to assess the effects of both humidity and corrosive environments on lap specimens. It is suggested that this technique may ultimately provide a method to quantify the amount of hidden damage in an adhesive joint subjected to fatigue, moisture or corrosive environments.     

大面积水域浓度场测试方法及系统研究

针对大面积水域浓度场难以实现实时测量、测量精度不高等问题,采用了一种多通道荧光测试系统和方法。首先,基于单色光诱导荧光检测浓度(LIF)原理,使用探头获取离散点的浓度参数。然后,经总线或通信网络技术,将数百个测点连接起来。最后,通过数据总线或网络将采集的数据输送到中央测控计算机中,处理离散的数据后形成完整的浓度场。在恒定流浓度场中的试验结果表明,污染物测量相对误差均值不超过5%,单次测量相对误差最高值为8.33%,传感器线性度不超过5%,可检测的荧光素钠溶液浓度分辨率为0.001 ppm,系统测量稳定、精度较高。相较于其他浓度测量方法,该系统具有测量面积大、实时测量的优势,可为水污染防治等领域提供可靠的技术支撑。     

Layering garments during rest and exercise in the cold (8°C): wearer responses and comparability with selected fabric properties

How garments contribute to performance of the clothing system during wear is of interest, as is understanding the value of using fabric properties to inform end-use characteristics. To investigate the influences of layering upper-body garments, four fabrics were used to construct two first-layer garments (wool and polyester) and two outer-layer garments (wool and membrane laminate). Over six sessions, 10 moderately trained males wore each first-layer garment as a single layer and in combination with each outer-layer garment while resting, running and walking in cold environmental conditions (8 ± 1°C, 81 ± 4% RH). Here, the type of garment arrangement worn (fabric type or number of layers) had little influence on heart rate, core body temperature and change in body mass. Weighted mean covered skin temperature was warmer and weighted mean next-to-skin vapour pressure was typically higher (following the onset of exercise) with two layers versus one. Differences among fabrics for individual properties were typically overstated compared to differences among corresponding garments for physiological and psychophysical variables under the conditions of this study. These findings inform the interpretation of particular fabric properties and highlight issues to be acknowledged during development/refinement of fabric test methods.

Practitioner Summary: We examined the way in which selected fibre, fabric and garment (layering) characteristics contribute to performance of the clothing system during wear under cold conditions. Selected properties of the constituent fabrics were found to provide limited insight into how garments perform during wear under the conditions of this study.     

Testing scientific software: A systematic literature review

ContextScientific software plays an important role in critical decision making, for example making weather predictions based on climate models, and computation of evidence for research publications. Recently, scientists have had to retract publications due to errors caused by software faults. Systematic testing can identify such faults in code.ObjectiveThis study aims to identify specific challenges, proposed solutions, and unsolved problems faced when testing scientific software.MethodWe conducted a systematic literature survey to identify and analyze relevant literature. We identified 62 studies that provided relevant information about testing scientific software.ResultsWe found that challenges faced when testing scientific software fall into two main categories: (1) testing challenges that occur due to characteristics of scientific software such as oracle problems and (2) testing challenges that occur due to cultural differences between scientists and the software engineering community such as viewing the code and the model that it implements as inseparable entities. In addition, we identified methods to potentially overcome these challenges and their limitations. Finally we describe unsolved challenges and how software engineering researchers and practitioners can help to overcome them.ConclusionsScientific software presents special challenges for testing. Specifically, cultural differences between scientist developers and software engineers, along with the characteristics of the scientific software make testing more difficult. Existing techniques such as code clone detection can help to improve the testing process. Software engineers should consider special challenges posed by scientific software such as oracle problems when developing testing techniques.     

Global software testing under deadline pressure: Vendor-side experiences

ContextIn the era of globally-distributed software engineering, the practice of global software testing (GST) has witnessed increasing adoption. Although there have been ethnographic studies of the development aspects of global software engineering, there have been fewer studies of GST, which, to succeed, can require dealing with unique challenges.ObjectiveTo address this limitation of existing studies, we conducted, and in this paper, report the findings of, a study of a vendor organization involved in one kind of GST practice: outsourced, offshored software testing.MethodWe conducted an ethnographically-informed study of three vendor-side testing teams over a period of 2 months. We used methods, such as interviews and participant observations, to collect the data and the thematic-analysis approach to analyze the data.FindingsOur findings describe how the participant test engineers perceive software testing and deadline pressures, the challenges that they encounter, and the strategies that they use for coping with the challenges. The findings reveal several interesting insights. First, motivation and appreciation play an important role for our participants in ensuring that high-quality testing is performed. Second, intermediate onshore teams increase the degree of pressure experienced by the participant test engineers. Third, vendor team participants perceive productivity differently from their client teams, which results in unproductive-productivity experiences. Lastly, participants encounter quality-dilemma situations for various reasons.ConclusionThe study findings suggest the need for (1) appreciating test engineers’ efforts, (2) investigating the team structure’s influence on pressure and the GST practice, (3) understanding culture’s influence on other aspects of GST, and (4) identifying and addressing quality-dilemma situations.