标准物质在分析测试中的重要地位及发展前景

标准物质在分析测试领域中无论在定值，方法的研究，误差确定等方面都有着重要地位。标准物质的质量保证及正确使用也应引起我们重视。随着科学技术迅速发展标准物质有着广阔发展前景。     

碳素材料超声检测的信号处理方法

针对碳素材料超声无损检测存在信噪比较低的问题,从自相关性出发分析了典型超声检测信号的组成成分,提出了在自相关分析的基础上的小波去噪思想,探讨了自相关分析和小波分析相结合的信号处理方法。利用此方法进行实际超声信号分析效果良好。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

书立复合冲裁模的设计

介绍了安装在液压试验机上的一种集冲裁、切口作用于一体的复合冲裁模的设计，解决了没有压力机的情况下冲裁件的加工问题。     

新型刮刀钻头的设计及现场试验研究

在理论分析的基础上，综合PDC钻头和刮刀钻头的优点，设计了一种新型的刮刀钻头，并进行了现场试验。现场试验结果表明，该钻头运转平稳，采用低钻压、高转速，钻进速度快，井眼规则通畅，有较明显的防斜作用，该种钻头的推广应用对提高钻井工程的整体效益具有十分重要的意义。     

水力压裂净压力拟合分析解释技术研究与应用

基于三维裂缝延伸模拟模型的水力压裂净压力拟合分析解释技术,提出了净压力拟合分析解释的一般步骤及理论方法,研究了现场监测净压力的计算方法,并介绍了其在现场施工中的应用情况。该技术可以帮助认识地层参数和压裂参数,提高压裂施工成功率和有效率。     

羟基磷灰石涂层人工关节的应用研究

采用人工合成高纯度的羟基磷灰石粉末，喷涂在具有注册证的钛合金和钴铬钼合金人工关节上。通过生物学基础检测、动物实验和临床试用，证明所制作的各种羟基磷灰石涂层人工关节，能诱发骨质生长，起生物固定作用，对治疗丧失功能的骨胳效果甚佳。     

异常高压低渗透地层测试技术的改进

针对异常高压低渗透地层在测试关井恢复过程中出现关井压力外泄的情况，对测试管柱进行了改进，即在P—T封隔器上方组装一个水力锚，水力锚上方组配一个裸眼旁通阀，封隔器和水力锚之间加1—2根油管，并适当增大关井时的加压负荷，较好的解决了关井压力外泄问题，提高了测试一次成功率。     

Analysis and Simulation of S-shaped Waveguide in Silicon-on-insulator

The simulation and analysis of S-shaped waveguide bend are presented.Bend radius larger than 30 mm assures less than 0.5 dB radiation loss for a 4-μm-wide silicon-on-insulator waveguide bend with 2-μm etch depth.Intersection angle greater than 20° provides negligible crosstalk (<-30 dB) and very low insertion loss.Any reduction in bend radius and intersection angle is at the cost of the degradation of characteristics of bent waveguide and intersecting waveguide, respectively.     

A Mixed-Approach Analysis of Deformations in Pipe Bends. Part 3. Calculation of Bend Axis Displacements by the Method of Initial Parameters

A problem of deformation of a curved shell loaded by internal pressure, axial force, and temperature difference is discussed. Physical equations are derived whereby the displacements and angles of rotation of the line of centers of mass of cross sections of a shell are related to loading parameters. A general constitutive set of equations for a curved element during its deformation is given. Using a method of initial parameters, an analytical solution is obtained for the differential equations for displacements and angles of rotation of the center line allowing for the action of distributed forces and moments.