Evolution of grain structure in thin film reactions

In this paper, we examine, both experimentally and theoretically, the kinetics of formation and microstructure of product phases in thin film reactions, using the Nb/Al and Ti/Al systems as our prototypes. The results of calorimetry and microscopy studies are interpreted using simple kinetic and morphology models. In particular, the kinetic models employed here focus on the nucleation and growth components of the phase formation process and the morphology models provide a starting point for the classification of product grain structures. An erratum to this article is available at .     

钛容器的特点

根据钛材的化学、物理、力学和工艺性能介绍了钛容器在设计、制造、检验和应用方面的特点。     

转炉溅渣护炉技术

溅渣工艺是用高压和大流量氮气通过氧枪将渣喷溅涂挂到全部转炉炉衬上。此技术使炉衬寿命延长，喷补料消耗降低，增加生产率，明显地降低操作成本。     

应用音平化渣图象分析和指导转炉造渣操作

利用音平化渣图象可以清晰地看出在转炉造渣过程中何时发生喷溅，何时发生炉渣返干和何时化渣正常。应用音平化渣图象和炉渣三元相图，可以正确地分析发生喷溅和返干的原因，从而找到避免突发性喷溅和严重返干的方法。正确的枪位和炉渣碱度控制是实现平稳吹炼的保证，而音平化渣图象能帮助操作工实现这一目标。     

Study on combustion characteristics of blended coals

Power plants in China have to burn blended coal instead of one specific coal for a variety of reasons. So it is of great necessity to investigate the combustion of blended coals. Using a test rig with a capacity of 640 MJ/h with an absolute milling system and flue gas online analysis system, characteristics such as burnout, slag, and pollution of some blended coals were investigated. The ratio of coke and slag as a method of distinguishing coal slagging characteristic was introduced. The results show that the blending of coal has some effect on NO _x but there is no obvious rule. SO _x emission can be reduced by blending low sulfur coal. Translated from Proceedings of the CSEE, 2005, 25(18): 97–103 [译自: 中国电机工程学报]     

高炉炉渣流动性的实验研究

以宝钢高炉渣中的四大组元(CaO,SiO2,Al2O3,MgO)为基础,实验研究MgO,Al2O3含量及碱度对炉渣的熔化性温度和流动性的影响.结果表明,炉渣中Al2O3含量控制在16%,配制适量的MgO(9%～10%),在1 500℃以上的高温区域,炉渣仍能保持正常的流动性,适合炉缸温度充沛的高炉使用;MgO含量由6%增加到10%时,较明显地降低了炉渣粘度,粘度的递减值约为0.07～0.15 Pa.s.     

助催化剂对TiCl_4/MgCl_2催化丙烯高温聚合的影响

研究了助催化剂种类(三甲基铝、三异丁基铝、三正己基铝、三乙基铝和甲基铝氧烷)及其含量对无内、外给电子体的TiCl4/MgCl2催化剂催化丙烯高温(100℃)聚合性能的影响,并用结晶分级分析、示差扫描量热和凝胶渗透色谱等方法分析了所得聚丙烯的结晶熔融行为和微观结构。实验结果表明,聚合温度从70℃升至100℃时,TiCl4/MgCl2催化剂的定向能力基本不变;100℃聚合时,以烷基化能力较弱的三异丁基铝为助催化剂时TiCl4/MgCl2催化剂的活性最高,而采用烷基化能力最强的三甲基铝为助催化剂时TiCl4/MgCl2催化剂的活性最低;100℃聚合时,助催化剂的种类对TiCl4/MgCl2催化剂的定向能力影响很小。     

钒钛渣对刚玉莫来石耐火材料的侵蚀研究

通过不同温度下钒钛渣对刚玉莫来石耐火材料的侵蚀实验，分析了炉渣、温度对材料的影响，认为致密结构、低气孔率是提高炉衬寿命的关键，板条状莫来石的存在利于减缓渣的侵蚀过程。     

Oxidation of porous nanocrystalline titanium nitride. II. Scale structure and composition

We have used x-ray phase analysis to study the composition of the products of reaction between oxygen and nanocrystalline powders with particle sizes 15, 40, 55, and 80 nm, and also specimens pressed (and sintered) from them. The powders were oxidized in air at 100°C (400 h) to 500°C (5 min), while the sintered specimens were oxidized at 600–900°C for 15, 120, and 240 min. In all cases, in the initial oxidation step the oxynitride Ti(O_xN_y) is formed, which over time is oxidized to TiO, Ti₂O₃, Ti₃O₅, TiO₂ (anatase) and TiO₂ (rutile). In the range 600–800°C, formation of a continuous oxide layer and conversion of anatase to rutile slows down diffusion of oxygen in the scale. We have established that at 900°C, the growth rate of the scale thickness increases and so the reflections from the oxynitride are barely noticeable on the diffraction patterns taken from the surface of the oxidized specimen. In these diffraction patterns, along with strong reflections from the rutile, we also observed weak reflections from lower oxides and anatase, which may be due to reaction between oxygen and the titanium ions diffused to the scale surface. We have concluded that at T > 850°C, the mechanism for oxidation of TiN changes. This is due to superposition of counterdiffusion of titanium ions on the diffusion of oxygen. __________ Translated from Poroshkovaya Metallurgiya, Nos. 3–4(448), pp. 72–78, March–April, 2006.     

电炉钢外来夹杂控制的研究

介绍了夹杂物的来源,包括内生夹杂和外来夹杂,着重于二次氧化产物、卷渣、内衬侵蚀.同时介绍了鄂钢电炉厂在冶炼和连铸过程中控制夹杂物的操作实践.