切削加工表面完整性建模现状与发展趋势

针对切削加工表面完整性建模方法种类繁多且相互关系揭示不明等问题,总结了各表面完整性指标,包括表面形貌、残余应力、加工硬化和相变的主要建模方法,并从各建模方法的应用范围以及主要成果的角度概括了表面完整性建模的研究现状.论述了解析建模与数值建模方法在预测表面完整性各指标时的优缺点及内在联系,重点分析了数值模拟技术在表面完整性建模中的作用.指出了国内外表面完整性研究体系的区别及联系,并对表面完整性建模的发展方向作了展望.     

载体材料表面性质对定形相变材料相变行为的影响

为了研究载体材料与相变材料的界面相互作用机制,以聚乙二醇(PEG)为相变材料、分子筛MCM-48和有序介孔碳CMK-5为载体材料,采用物理共混的方法制备PEG/MCM-48和PEG/CMK-5两类定形相变材料.利用氮气吸附、TEM、FT-IR、XRD和DSC等表征技术,研究定形相变材料中载体材料的表面性质对相变材料PEG的定形能力、结晶度、相变行为的影响规律.研究结果表明,CMK-5和MCM-48具有相似的有序介孔结构,但是其化学组成不同;CMK-5与PEG的界面相互作用力弱于MCM-48与PEG的界面相互作用力.因此,PEG在CMK-5中的结晶度和相变焓均大于其在MCM-48中的结晶度和相变焓.     

芳纶纤维表面改性及其对芳纶纸力学性能的影响

利用氯磺酸、醋酸酐对芳纶短切纤维进行了改性处理,再用处理后的纤维配抄芳纶纸,探讨了处理工艺对芳纶纸力学性能的影响.结果表明,当氯磺酸浓度为2%,处理时间为10min,处理温度为50℃时,芳纶纸的力学性能较好.用100%的醋酸酐对芳纶纤维进行处理然后配抄成纸,所得纸张的抗张指数和撕裂指数分别提高了63.8%和21.4%.另外,芳纶纤维经过醋酸酐浸泡1min后再用甲醇处理3min,芳纶纸的抗张指数和撕裂指数分别提高了84.7%和38.4%.     

Experimental Study of Machinability in Millgrinding of SiCp/Al Composites

An attempt was made to investigate the machinability of Si Cp/Al composites based on the experimental study using mill-grinding processing method. The experiments were carried out on a high-speed CNC machining center using integrated abrasive cutting tool. The effects of combined machining parameters, e g, cutting speed(vs), feed rate(vf), and depth of cut(ap), with the same change of material removal rate(MRR) on the mill-grinding force and surface roughness(Ra) were investigated. The formation mechanism of typical machined surface defects was analyzed by SEM. The experimental results reveal that with the same change of material removal rate, lower mill-grinding force values can be gained by increasing depth of cut and feed rate simultaneously at higher cutting speed. With the same change of MRR value, lower surface roughness values can be gained by increasing the feed rate at higher cutting speed, rather than just increasing the depth of cut, or increasing the feed rate and depth of cut simultaneously. The machined surface of Si Cp/Al composites reveals typical defects which can influence surface integrity.     

基于解析解的四阶PDE曲面裁剪方法

该文提出了一种可以广泛应用于四阶PDE曲面的裁剪方法。利用PDE的参数域内的曲线在曲面上投影,得到所求裁剪曲面的边界曲线,然后通过边界曲线的导矢与曲面在边界曲线处的法向量得到边界曲线处的跨界导矢,最后以求得的裁剪曲面的边界曲线以及裁剪曲面在边界曲线处的跨界导矢为PDE曲面的边界条件,用四阶的PDE曲面方程求得PDE裁剪曲面。     

基于弯矩影响面方法的单向板移动荷载最不利位置研究

采用影响面的方法,运用matlab数值分析软件对移动荷载下板的弯矩变化进行了模拟分析。通过控制板的长短边比例,得出不同工况下移动荷载的最不利位置,同时对影响最不利位置的因素进行了相关的模拟研究,得出了长宽比越大的板,其受移动荷载的影响越小的结论。对今后具体的工程计算具有一定的参考意义。     

Velocity estimation of moving targets with stepped-frequency radar based on Doppler frequency difference

By analyzing the signal model of stepped-frequency waveform, a novel method for velocity measurement is proposed. The method is based on Doppler frequency difference which is achieved by using Hough transform. As the estimated velocity is inversely proportional to the frequency step size instead of the carrier frequency of the transmitted signal as the pulse-Doppler （PD） processing, the new algorithm can achieve much wider unambiguous velocity range. Furthermore, non-coherent integration of the sub-pulses with different carrier frequencies can be implemented by Hough trans- form to improve the anti-noise performance. Besides, field experimental results show that the high range resolution profile （HRRP） of a bullet with high speed can be reconstructed correctly without distortion.     

气雾射流动态传热实验研究

设计搭建了气雾射流动态传热实验装置,建立了二维非稳态导热反问题模型,研究了表面温度和表面热流密度的时间分布.结果表明在冷却过程中缸体穿越喷射区与淌水区历经了几个不同的换热阶段,温度曲线出现了明显的周期性的特点,成功的模拟了连铸二冷气雾冷却周期性换热的特征.     

易碎弹复合材料动态特性数值研究

利用Split Hopkinson Pressure Bar （SHPB）实验装置获取复合材料易碎弹试件的动态力学特性,并应用LS-DYNA软件对SHPB实验过程进行数值模拟.结合SHPB应力波理论,研究不同撞击速度对试件破坏程度、压杆轴向应变波形以及试件动态力学特性的影响.仿真结果表明：试件仿真结果与实验结果基本吻合,说明SHPB实验仿真是可行的;试件的破坏程度随着撞击速度的增大而显著,但压杆轴向应变波形以及试件动态力学特性随着撞击速度的增大变化不明显.     

Non-complete relief method for measuring surface stresses in surrounding rocks

The measurement of surface stresses in surrounding rocks with the use of a relief method of annular hole-drilling was studied by numerical analysis. The stress relief process by hole-drilling was then simulated with the use of finite element method. The influences of the borehole diameter（d）, the initial stresses and the ratio of the initial principle stresses on the variations of the remained stress and the released stress in function of the relief depth（h） were discussed. The relation between the non-dimensional ratio of the released principle strains and that of the initial principle stresses, and the effect of the elastic modulus and the Poisson ratio of the rock mass on the stress relief curves were studied. The results show that the stress relief behavior formulated with the non-dimensional ratio of the released stress and the ratio of h/d is only sensitive to the ratio of the initial principle stresses and the Poisson ratio. The stresses are completely released when h equals 1.6d, and the tensile stresses take place on the bore core surface in the relief measurement process. Finally, a non-complete relief method of annular hole-drilling for measuring surface stress in surrounding rocks is proposed and the procedure is presented.