矿山岩土工程系统环境质量评价指标体系

矿山现行的环境影响评价及其提交的环境影响报告书,是将矿山开发视为单个建设项目且只注重污染物排放和简单数量分析的单要素评价.本文将矿山开发视为统一系统,充分考虑系统内矿石开采、废石场、尾矿库等岩土工程及其矿岩氧化淋滤产生的毒害物质对矿区及其区域水土环境潜在而长期的影响,建立矿山岩士工程系统环境质量评价的指标体系,以改变矿山环境评价的传统旧式,规范和监督矿山开采行为,实现矿业开发与环境保护的协调发展.     

Effects of gallia additions on sintering behavior of gadolinia-doped ceria

The effects of gallia additions on the sintering behavior of gadolinia-doped ceria were systematically investigated from the following aspects: the variation in sintered density, the variation in grain size, and the existing forms of Ga₂O₃ in CeO₂.Sintered density increased with increasing Ga₂O₃ content up to 5 mol.% and then it decreased with further addition of Ga₂O₃. Grain size also increased with increasing Ga₂O₃ content up to 5 mol.% and then decreased with further addition of Ga₂O₃. Decrease in grain size was caused by a pinning effect of Ga₂O₃ precipitation at grain boundaries. Lattice constant decreased with increasing Ga₂O₃ content up to 5 mol.%. This decrease will be due to the substitution of smaller Ga³⁺ ions for Ce⁴⁺ ions in the CeO₂ structure. According to the results obtained from scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses, the solubility limit of Ga₂O₃ in Ce_0.8Gd_0.2O_1.9 ceramics can be estimated to be nearly 5 mol.%. The addition of Ga₂O₃ up to the solubility limit was found to promote the sintering properties of Gd₂O₃-doped CeO₂.     

Discrimination of B–C–N nanotubes through energy-filtering electron microscopy

Various multi-walled nanotubes in the B–C–N system are thoroughly investigated using a JEOL-3100FEF high-resolution field emission transmission electron microscope operating at 300 kV and equipped with an in-column built Omega filter. Spatially-resolved B, C and N elemental maps of the nanotubes are constructed. It is realized that a wide variety of tubular arrays composed of B, C and N atoms may exist in the system. Sandwich-like BN-rich and C-rich alternating tubular shells, graphitic C layers inside and outside of pure BN shells induced either by surface contamination, or electron beam irradiation, separation of C-rich and BN-rich tubes and/or BN particles within tubular bunches may take place. One should carefully take these effects into account while analyzing nanotube physical properties, e.g., electrical or optical, rather than simply rely on electron energy loss spectra typically collected from B, C and N containing nanostructures as a whole. Striking dependence of an individual nanotube electrical conductivity on tubular shell chemistry is demonstrated using I–V curve recording in an atomic force microscope.     

Comparative Study of Different Adaptive Window Protocols

We study an Adaptive Window Protocol (AWP) with general increase and decrease profiles in the presence of window dependent random losses. We derive a steady-state Kolmogorov equation, and then obtain its solution in analytic form for particular TCP versions proposed for high speed networks, such as Scalable TCP and HighSpeed TCP. We also relate window evolution under an AWP to workload process in queueing systems; this observation gives us a way to compare various AWP protocols.     

Assessing organo-clay dispersion in polymer layered silicate nanocomposites: A SAXS approach

A SAXS method for the quantitative assessment of the morphology of polymer layered silicate nanocomposites is proposed. Fitting the SAXS patterns, the number of clay layers, the periodicity of the layers in the tactoids, the thickness of the regions interposed between the clay platelets and their distributions can be measured. A good agreement with TEM data was obtained, avoiding the inconsistencies with microscopical observations often reported in the literature.     

Catalytic properties and electronic structure of copper ions in Cu-ZSM-5

The effect of ion exchange conditions, such as Si/Al ratio, precursor copper salt, pH and concentration of the solution, on the catalytic activity in SCR of NO by propane and on the electronic state of copper ions in Cu-ZSM-5 has been studied. The NO conversion in NO SCR by C₃H₈ has been found to reach a maximum value at Cu/Al ratio about 0.37–0.4 and remain constant at higher Cu/Al.

ESR and UV–vis DR spectroscopy have been used to elucidate stabilization conditions of copper ions in Cu-ZSM-5 zeolites as isolated Cu²⁺ ions, chain copper oxide structures and square-plain oxide clusters. The ability of copper ions for reduction and reoxidation in the chain structures may be responsible for the catalytic activity of Cu-ZSM-5. These transformations of copper ions are accompanied by the observation of intervalence transitions Cu²⁺–Cu⁺ and CTLM of the chain structures in the UV–vis spectra.     

Corrosion Behavior of 316LN and 316 Stainless Steels During Long-term Exposure to Aerated 0.5 M NaCl Using Electrochemical Noise Technique

In the present work 316LN as well as 316 stainless steel (SS) coupons each of dimensions (0.025 × 0.018 × 0.006 m³) in well-polished condition were used as two nominal electrodes which were immersed in the aerated solution of 0.5 M NaCl. Correlated current and potential electrochemical noise (EN) signals were collected at 1 Hz sampling frequency for 1 h daily over a period of 30 days. The detrended EN data were used to calculate the noise resistance (R _N) as well as the spectral noise resistance at zero frequency (R _SN^o) values and other statistical parameters. To study the nature of pits and distribution of their diameters as well as depths, extensive observations of the pitted and the blank specimens were carried out using Confocal Laser Scanning Microscopy (CLSM). The current and the potential records of the two alloys showed distinct differences in their corrosion behavior. It was observed that within less than 4 h of immersion, 316SS showed signals indicative of unstable pitting and onset of stable pitting was noticed after 48 h of exposure. However, until about 24 h, 316LN showed just the random signals and unstable pitting was observed after 28 h. The signals clearly indicated continuous growth of the stable pits in 316SS as against the repassivation of the unstable pits in 316LN after 7 days exposure. It was observed that R _N values showed a continuous decrease in the case of 316SS, but were quite stable in the case of 316LN over the exposure period. Concurrent to these observations it was observed that 316SS specimen was extensively pitted. The frequency distributions of pit diameters as well pit depths were observed to be highest at 10-20 μm and 5-10 μm, respectively. However, pits with as large as 70-80 μm diameter and as deep as 20-25 μm too were observed. No pits were observed in case of 316LN even after 30 days of exposure, an observation that corroborates well with the stable R _N values. Thus, in the present investigation, the long-term tests using EN technique coupled with CLSM studies conclusively prove that many unstable pits initiated in 316SS turn into stable ones resulting in insidious localized corrosion attack whereas the unstable pits initiated in 316LN get passivated in the simulated coastal environment.     

Grain growth kinetics in Dy-doped Bi0.5Na0.5TiO3 ceramics

Dysprosium-doped bismuth sodium titanate ceramics were prepared using the conventional mixed-oxide method. The amount of dysprosium used was varied from 0 to 2 at.%. The mixed powders were calcined at 800 °C and checked for phase purity using X-ray diffraction technique. The calcined powders were then cold-pressed into pellets and sintered at 1050 °C for the time ranging from 2 to 48 h. The ceramics were checked for phases and microstructures using an X-ray diffractometer and a scanning electron microscope, respectively. The analysis showed that undoped BNT ceramics sintered at longer time exhibited a significant grain growth with non-uniform grain size distribution and shape. The Dy-doped BNT however showed a much more limited grain growth behavior, resulting in smaller grain size and more equiaxed grain shape. It was also found that all Dy-doped BNT ceramics sintered at 48 h possessed lower porosity than those sintered for shorter time.     

用于实时数据传输的滑动帧方法及其实现

根据某雷达系统对测量信号的快速传输要求,提出采用滑动帧的处理方法并在FPGA中实现,克服了传统帧处理难以满足快速传输要求的不足。阐述了滑动帧结构的构造思想,详述了滑动帧结构的特点及具体功能模块的实现。根据实际应用需求构造了滑动帧结构处理器,试验和应用结果表明设计可行有效,能充分满足实时数据传输的要求。