轴对称型面喷管推力计算方法

为分析喷管内流场的变化,使用 1 维计算模型和基于 FLUENT 的 2 维计算模型对轴对称型面喷管的推力 进行计算,分析 2 种计算结果的差异。利用正交设计法,研究喷管的燃烧室压强、扩张角、扩张比、扩张段长度以 及燃气射流的黏度对喷管推力计算的影响。结果表明：推力差异与燃烧室压强近似线性关系;推力差异随着燃气黏 度的增加而增大;当初始扩张角越大、出口扩张角越小时,推力差异越小;推力差异随着扩张比、扩张段长度与喉 部半径比的增加先减小后增加;在低压、低黏度的情况下,1 维计算方法可用于喷管推力的计算,否则,2 维计算方 法更适合。     

掺混燃油在离心喷嘴内的流动与雾化特性研究

燃料性质的改变会导致雾化特性的变化,针对乙醇掺混航空煤油在离心式压力雾化喷嘴内的流动与雾化特性开展了研究。通过耦合流体体积法(VOF)和离散相模型(DPM),研究了不同乙醇掺混体积分数下掺混燃油在离心式喷嘴中的内部流动和外部雾化过程。研究结果表明：在压差不变时,喷嘴内空气芯直径随着掺混燃油内乙醇体积分数的增加而增大;而液膜厚度则与空气芯直径成反比,随着乙醇体积分数的增加而减小。喷嘴出口的速度随着乙醇体积分数的增加而增大;在油膜表面的波动及气动力的共同作用下,油膜失稳形成液滴,获得了不同比例下掺混燃油在喷雾外流场内的喷雾粒径分布特征,随着掺混乙醇体积分数的增加,液滴的平均直径逐渐减小。     

Residual stress determination in a dissimilar weld overlay pipe by neutron diffraction

Residual stresses were determined through the thickness of a dissimilar weld overlay pipe using neutron diffraction. The specimen has a complex joining structure consisting of a ferritic steel (SA508), austenitic steel (F316L), Ni-based consumable (Alloy 182), and overlay of Ni-base superalloy (Alloy 52M). It simulates pressurized nozzle components, which have been a critical issue under the severe crack condition of nuclear power reactors. Two neutron diffractometers with different spatial resolutions have been utilized on the identical specimen for comparison. The macroscopic ‘stress-free’ lattice spacing (d_o) was also obtained from both using a 2-mm width comb-like coupon. The results show significant changes in residual stresses from tension (300-400 MPa) to compression (−600 MPa) through the thickness of the dissimilar weld overlay pipe specimen.     

Taum Sauk抽水蓄能工程系列报道(Ⅲ)——Taum Sauk上水库的重建

Taum Sauk上水库重建工程主要是新建一座现代化的混凝土面对称碾压混凝土(RCC)坝来取代原有的土石坝.由于该坝是美国最大的RCC项目并采用了对称断面和相对低强度的RCC,设计中需要解决许多问题.文章总结了相关设计事项,并简要介绍了施工过程,供参考.     

Axiomatization and conditions for neighborhoods in a covering to form a partition

In this paper, we study the axiomatic issue of a type of covering upper approximation operations. This issue was proposed as an open problem. We also further some known results by using only a single covering approximation operator to characterize the conditions for neighborhood {N(x): x ∈ U} to form a partition of universe U.     

Industrial Experiment of Reducing Superheat of Steel by Nozzle Cooling

 Nozzle cooling equipment is developed to supervise and control the heat flux by changing water flux. An industrial experiment is held in billet caster in Huaigang . The results show that cooling control system works stably and effectively to control the heat fluxes by the temperature of copper tube. The superheat of steel in mould is reduced and the equiaxed crystal ratio, as well as compact degree of steel is raised.     

包钢炼铁厂降低中速磨废料排出量的措施

包钢炼铁厂喷煤系统中速磨废料排出量大,既浪费资源又影响台时产量,近几年一直在摸索如何降低废料排出量。2001年通过改造中速磨喷嘴环,调整系统参数,废料排出量大幅降低。文中对此次改造的措施及效果进行了分析总结。     

Notebook computer use on a desk,lap and lap support: Effects on posture,performance and comfort

This study quantified postures of users working on a notebook computer situated in their lap and tested the effect of using a device designed to increase the height of the notebook when placed on the lap. A motion analysis system measured head, neck and upper extremity postures of 15 adults as they worked on a notebook computer placed on a desk (DESK), the lap (LAP) and a commercially available lapdesk (LAPDESK). Compared with the DESK, the LAP increased downwards head tilt 6° and wrist extension 8°. Shoulder flexion and ulnar deviation decreased 13° and 9°, respectively. Compared with the LAP, the LAPDESK decreased downwards head tilt 4°, neck flexion 2°, and wrist extension 9°. Users reported less discomfort and difficulty in the DESK configuration. Use of the lapdesk improved postures compared with the lap; however, all configurations resulted in high values of wrist extension, wrist deviation and downwards head tilt.

Statement of Relevance: This study quantifies postures of users working with a notebook computer in typical portable configurations. A better understanding of the postures assumed during notebook computer use can improve usage guidelines to reduce the risk of musculoskeletal injuries     

Risk of musculoskeletal disorders among females and males in repetitive/constrained work

This paper combines epidemiological data on musculoskeletal morbidity in 40 female and 15 male occupational groups (questionnaire data 3720 females, 1241 males, physical examination data 1762 females, 915 males) in order to calculate risk for neck and upper limb disorders in repetitive/constrained vs. varied/mobile work and further to compare prevalence among office, industrial and non-office/non-industrial settings, as well as among jobs within these. Further, the paper aims to compare the risk of musculoskeletal disorders from repetitive/constrained work between females and males. Prevalence ratios (PR) for repetitive/constrained vs. varied/mobile work were in neck/shoulders: 12-month complaints females 1.2, males 1.1, diagnoses at the physical examination 2.3 and 2.3. In elbows/hands PRs for complaints were 1.7 and 1.6, for diagnoses 3.0 and 3.4. Tension neck syndrome, cervicalgia, shoulder tendonitis, acromioclavicular syndrome, medial epicondylitis and carpal tunnel syndrome showed PRs > 2. In neck/shoulders PRs were similar across office, industrial and non-office/non-industrial settings, in elbows/hands, especially among males, somewhat higher in industrial work. There was a heterogeneity within the different settings (estimated by bootstrapping), indicating higher PRs for some groups. As in most studies, musculoskeletal disorders were more prevalent among females than among males. Interestingly, though, the PRs for repetitive/constrained work vs. varied/mobile were for most measures approximately the same for both genders. In conclusion, repetitive/constrained work showed elevated risks when compared to varied/mobile work in all settings. Females and males showed similar risk elevations. This article enables comparison of risk of musculoskeletal disorders among many different occupations in industrial, office and other settings, when using standardised case definitions. It confirms that repetitive/constrained work is harmful not only in industrial but also in office and non-office/non-industrial settings. The reported data can be used for comparison with future studies.     

Individual finger contribution in submaximal voluntary contraction of gripping

The objective of this study was to evaluate individual finger force and contribution to a gripping force, the difference between actual and expected finger forces and subjective discomfort rating at 10 different submaximal voluntary contraction (%MVC) levels (10–100% in 10 increments). Seventy-two participants randomly exerted gripping force with a multi-finger force measurement system. The individual finger force, gripping force and discomfort increased as %MVC levels increased. The middle and ring fingers exerted more force and contributed to a gripping force more than the index and little fingers due to their larger mass fractions of the digit flexor muscles. It was apparent at <50% MVC; however, the index finger increased its contribution and exerted even more force than expected at more than 50% MVC. Subjective discomfort supported the results of the objective measures. This could explain the conflicting findings between index and ring fingers in previous finger contribution studies.

Statement of Relevance: Hand tool design is of special interest in ergonomics due to its association with musculoskeletal disorders in the hand. This study reveals a different contribution pattern of the fingers in submaximal voluntary contraction of gripping exertion.