发电设备的检修策略及可靠性管理研究

检修策略和可靠性管理是发电厂设备管理工作相辅相成的 2个方面 ,必须予以足够重视。目前要加大力度做好可靠性管理工作 ,建立可靠性管理系统为发电设备管理提供技术支持 ,为设备检修提供依据 ,以获得最佳的经济效益。     

基于相关性的人机系统可靠性模型

本文在剖析人机系统中操作者行为特征的基础上,考虑到操作者行为的自适应性、自学习能力及其行为形成主因子,着重结合操作者行为的相关性-感知作用于判断决策后影响到动作,建立了人机系统中操作者行为模式,并推导出计算操作者可靠度的公式,求出了相应参数.最后进行了实例量度,同时定量辨识了行为相关性对人可靠性的制约程度,以期从人机系统可靠性角度为人机系统的优化设计提供新的依据.     

Quantitative demonstration and cost considerations of a software fault removal methodology

This paper presents a demonstration of a methodology for fault removal during software development. The methodology encompasses the entire development history, from system and software requirements generation to system test. Thus it considers not only the faults during software testing after formal configuration controls have been invoked, but also the faults discovered prior to that phase: during system and software requirements generation, preliminary design, detailed design and code and unit testing. The agents for fault discovery used in verification and validation are called activities, techniques and tools (AT & Ts) in this paper, each having a certain maximum potential or capability for fault discovery. The AT & Ts considered include the usual specification review activities, and also certain tools not normally applied in ‘standard’ software development, such as automated requirements aids. Application of the methodology yields numbers of residual faults as of each phase of development, including those remaining to be discovered during operations and maintenance. Some previous experience and data on residual faults correspond to these results, indicating that the methodology and choice of parameters are reasonable. The methodology also allows one to calculate a relative loss due to delay in fault discovery, which, as is well known, rises rapidly when faults are not discovered during the phase in which they are generated.     

超高速线路保护原理及应用

在广泛参阅了对暂态量保护的研究 ,对各种基于故障时产生暂态量的保护原理和技术特点及应用进行了分析比较 ,并指出了各种新型保护的优缺点及暂态量保护的发展趋势     

Different insights for improving part and system reliability obtained from exactly same DFOM “failure numbers”

Techniques for improving the reliability and maintainability of both nonrepairable and repairable items can be suggested by failure data analysis. It is shown that a given set of failure numbers leads to very different improvement strategies when the numbers are the times-between-successive-failures of one or more repairable items, rather than the times-to-failure of nonrepairable items. Since this should have been obvious more than 50 years ago, at the onset of formal reliability engineering activities, several reasons are proffered for the widespread and protracted misinterpretation of even the most basic—and simple!—conceptual and practical differences between nonrepairable and repairable items.     

Reliability Analysis of Single-Degree-of-Freedom Elastoplastic Systems. II: Suboptimal Excitations

A method for constructing an approximation of the critical excitation that drives an elastoplastic system from rest to a target threshold at a specified time instant, referred to as the “suboptimal excitation,” is presented in this paper. It is based on the observations gained from study of the critical excitations in the companion paper. Essentially, for the usual case of interest where the failure time is not small compared to the natural period, the duration of the positive and negative pulses of the critical excitation are roughly equal to half of the natural period. This consideration allows for a simple intuitive approximation of the critical excitation. The amplitudes of the positive and negative pulses are obtained in closed forms using energy balance. Numerical investigations show that the critical excitations are well approximated by the suboptimal excitations.     

Beyond Boundary Objects: Collaborative Reuse in Aircraft Technical Support

Boundary objects are a critical, but understudied, theoretical construct in CSCW. Through a field study of aircraft technical support, we examined the role of boundary objects in the practical achievement of safety by service engineers. Their resolution of repair requests was preserved in the organization’s memory via three compound boundary objects. These crystallizations did not manifest a static interpretation, but instead were continually reinterpreted in light of meta-negotiations. This suggests design implications for organizational memory systems which can more fluidly represent the meta-negotiations surrounding boundary objects.     

行波管质量与可靠性信息管理系统的设计

本文从应用角度简要介绍了《行波管质量与可靠性信息管理系统》的研制背景，数据库的数据来源，数据结构，系统构成及功能特点。     

多台并行随机CIMS可靠性的扩散估计界

ＣＩＭＳ可靠性模型随机研究的突出特点是工作站的并行结构使系统的状态个数呈现指数级增大，同时，并行结构与有限的缓冲库相互交织在一起，这使系统状态呈爆炸趋势，显然，对系统作精确的分析与系统呈现的状态爆炸趋势构成了难以解决的矛盾，如何解决这一矛盾正是ＣＩＭＳ随机理论有待开发的重要课题。我们把扩散近似方法引入到多台并行的ＣＩＭＳ可靠性模型中，以简单的连续过程描述了具有状态爆炸趋势的复杂离散过程，给出了ＣＩ     

试生产中产品的可靠性保证

阐述了试行产中产品质量和可靠性的主要保证方法，由于这些做法来自于工厂的生产实践，所以，对承制方，订购方等各级，各类人员都有借鉴意义。同时对理论工作者也有一定的参考价值。