Yeast mutants with increased bacterial transposon Tn5 excision

Five complementing recessive mutations that exhibit increased bacterial transposon Tn5 precise excision in yeast Saccharomyces cerevisiae were obtained by ethylmethanesulfonate treatment. One of these mutations (tex1) was submitted to extensive genetic analysis. tex1 is a recessive temperature-sensitive mutation resulting in a 20-100-fold increase in Tn5 excision. It also has increased frequencies of ochre mutation reversion, of forward mutation to canavanine resistance, and loss of chromosome III or its right arm. The possible mechanism of tex1 effects is discussed.     

Superconductivity at differentTc in CdBa2Ca2Cu3Oy

A Cd analogue of the Tl and Hgn =3 series with nominal composition CdBa₂Ca₂Cu₃O_y has been synthesized. The samples were superconducting according to magnetic susceptibility measurements. The critical temperature was 103 or 107 K depending on the preparation conditions. The EDX analysis revealed the presence of Cd-1111, Cd-1121, and Cd-2333 as minor phases. The observed diamagnetic effects were attributed to the differentT _c of these phases.     

短纤维增强透气性莫来石/铁(A3S2/Fe)复合材料烧结特性的研究

本文研究了A₃S₂/Fe复合材料的烧结特性、透气性和纤维增强效果,分析了烧结过程中材料宏观结构和微观组织的形成机理.实验结果表明:纤维增强A₃S₂/Fe复合材料在900～1000℃具有良好的烧结性能,烧成后表层存在一定厚度的硬化层;纤维增强效果显着.材料抗压强度达17～23MPa,相对透气系数为4.30～9.69cm3/(cm2·s·atm).已能满足实际应用的需要.     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

Structure evolution of conductive polymer composites revealed by solvent vapor induced time-dependent percolation

The authors of this paper synthesized a series of amphiphilic triblock copolymers of polystyrene-b-poly(ethylene glycol)-b-polystyrene (PS-PEG-PS) having different PEG/PS ratios with nearly identical molecular weights of the entire copolymers. The interfacial interactions in the composites consisting of carbon black and the copolymers can thus be tailored. When these conducting composites are exposed to certain solvent vapors, their electrical resistances greatly increase, showing the gas sensitivity. The present work indicated that this switching behavior is controlled by the structural relaxation of the composites because matrix swelling acts as the main mechanism. The response time has been correlated with absolute temperature by Arrhenius equation, and the estimated activation energy reflects mobility of the fillers involved in the solvent induced expansion of the surrounding polymer. Therefore, by using the gas sensibility of the conductive composites, the structure evolution of the composite materials in solid state and the effect of filler/matrix interfacial interaction on the relaxation property of the matrix polymer has been inspected. It was found that lower activation energy represents stronger interfacial interaction in case good solvent of the matrix was used for the test.     

La-OMS-2催化剂催化甲苯氧化制苯甲醛

合成了氧化锰八面体(OMS-2)分子筛,采用离子交换法和浸渍法制备了稀土金属La改性的OMS-2分子筛(La-OMS-2)催化剂,并用于甲苯液相选择性氧化制苯甲醛,考察了催化剂用量、反应温度、反应时间、氧气流量及溶剂种类对甲苯转化率和苯甲醛选择性的影响,对La-OMS-2催化剂进行了X射线衍射表征和BET比表面积测定。实验结果表明,离子交换法制备的La-OMS-2-A催化剂的活性高于浸渍法制备的La-OMS-2-B催化剂,在甲苯0.1mol、溶剂冰乙酸10mL、氧气流量60mL/min、La-OMS-2-A催化剂用量0.10g、反应温度353K、反应时间1.0h的条件下,甲苯转化率达61%,苯甲醛收率为56%。加入La对OMS-2分子筛中的MnO晶格结构产生了影响,提高了苯甲醛的收率。     

New approaches for error estimation and adaptivity for 2D potential boundary element methods

This work presents two new error estimation approaches for the BEM applied to 2D potential problems. The first approach involves a local error estimator based on a gradient recovery procedure in which the error function is generated from differences between smoothed and non‐smoothed rates of change of boundary variables in the local tangential direction. The second approach involves the external problem formulation and gives both local and global measures of error, depending on a choice of the external evaluation point. These approaches are post‐processing procedures. Both estimators show consistency with mesh refinement and give similar qualitative results. The error estimator using the gradient recovery approach is more general, as this formulation does not rely on an ‘optimal’ choice of an external parameter. This work presents also the use of a local error estimator in an adaptive mesh refinement procedure. This r‐refinement approach is based on the minimization of the standard deviation of the local error estimate. A non‐linear programming procedure using a feasible‐point method is employed using Lagrange multipliers and a set of active constraints. The optimization procedure produces finer meshes close to a singularity and results that are consistent with the problem physics. Copyright © 2002 John Wiley & Sons, Ltd.     

基于EWB的D/A数模转换器的仿真研究

阐述了D／A转换器的仿真原理，给出了T形电阻网络D／A转换器仿真模型的构造方法，并采用EWB进行了系统仿真，仿真结果表明该方法是合理、可行的。