First-principle study of ferroelectricity in PbTiO3/SrTiO3 superlattices

We performed the first-principles calculation to investigate the electronic structure and polarization behaviors in PbTiO₃/SrTiO₃ (PST) superlattices. The DOS (density of state) profiles show that there are strong hybridizations of atom Ti–O and Pb–O which play very important roles on ferroelectricity of the PbTiO₃/SrTiO₃ superlattices. Comparing to the corresponding paraelectric phase, we find the electrons of the PT (PbTiO₃) layers occupy lower energy states and electrons of the ST (SrTiO₃) layer occupy higher energy states. It is shown that the polarizations of the superlattices decrease with proportion of SrTiO₃ increasing. The constant polarization of local layer indicates that PST superlattices with small modulation lengthen can be approximately considered as a single ferroelectric material. Furthermore, according to electrostatic model, we find that directions of internal electric fields in PT and ST layers are opposite. In PST superlattices, internal electric field in PT layer leads to the loss of polarization of this layer, but the polarization of ST layer is induced by internal electric field of this layer. Compared to the value of the polarization in bulk PbTiO₃, polarization of PST is smaller.     

Solving regularized least squares with qualitatively controlled adaptive cross‐approximated matrices

The adaptive cross‐approximation (ACA) technique is applied to accelerating an inverse‐problem solver that estimates charge distribution on a dielectric spacer. The ACA generates an approximated system‐matrix that enables us to carry out high‐speed inverse calculation. We designed an approximation procedure based on ACA with some additional concepts, that is, (a) partitioning of matrix based on algebraic information, (b) approximation quality control based on matrix norms, and so on. The tested solver (LSQR for regularized least squares) with ACA demonstrates about 10 times faster performance than that without ACA. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 159(3): 10–18, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20326     

Short-term power sources for tokamaks and other physical experiments

The Compass-D tokamak is being planned to move from UKAEA Culham (England) be and reinstalled in IPP Prague (Czech Republic). An overview of Compass-D energetics is described in short. The new power sources have to be designed. Alternative solutions of power sources have been investigated. Ignitrons and mechanical breakers can be replaced by modern high-power semiconductors. With respect to the need of accumulated energy, new technologies of energy storage - supercapacitors and high-speed flywheels, not applied up to now in similar fusion projects, are characterized in comparison with traditional ones - capacitors and big motor-flywheel generators. It is shown that these technologies enhance possibilities in arrangement of power supplies for tokamaks as well as for other high-power demanding experiments with pulse length from fraction to tens of seconds.     

On the microhardness testing of electrically stressed poly(phenylene oxide): Polystyrene blends

Microhardness measurements have been performed on untreated (virgin) and electrically stressed, solvent‐cast laboratory‐prepared samples of pure poly(phenylene oxide) (PPO), pure polystyrene (PS), and PPO : PS polyblends with different weight proportions. Results of such measurement on untreated polyblend sample show that microhardness (H_v) increases with increase in the content of PS up to 10 wt %, which attributed to the existence of homogeneous phase morphology. However, this feature is not observable in samples containing higher content of PS. Electrical stress is found to modify considerably the mechanical property of polymer. The effect of electric field on the microhardness of such samples (PPO : PS :: 90 : 10) has been characterized by the existence of a peak. Trapping of charge carriers in electrically stressed samples imparts hardening to the polyblend up to an applied step field of 190 kV/cm. However, the excessive charging beyond this step field value destroys this characteristic. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Design and evaluation of an active electromechanical wheel suspension system

This paper presents an electromechanical wheel suspension, where the upper arm of the suspension has been provided with an electric levelling and a damper actuator, both are allowed to work in a fully active mode. A control structure for the proposed suspension is described. The complex design task involving the control of the electric damper and its machine parameters is tackled by genetic optimisation. During this process, these parameters are optimised to keep the power dissipation of the electric damper as low as possible, while maintaining acceptable comfort and road-holding capabilities. The results of the evaluations carried out demonstrate that the proposed suspension can easily adopt its control parameters to obtain a better compromise of performance than that offered by passive suspensions. If the vehicle is to maintain acceptable performance during severe driving conditions, the damper has to be unrealistically large. However, if the electric damper is combined with a hydraulic damper, the size of the electric damper is significantly reduced. In addition, the design of the electric damper with the suggested control structure, including how it regenerates energy, is discussed.     

电容比和方向性对自给能γ剂量计探头的影响

本文给出了自给能γ剂量计探头在γ射线照射下积累电荷的测量结果，讨论了电容比和方向性对自给能γ剂量计探头的影响以及探头的饱和点。     

Relation between microstructure, properties and spark plasma sintering (SPS) parameters of pure ultrafine WC powder

A combined experimental/numerical methodology is developed to fully consolidate pure ultrafine WC powder under a current-control mode. Three applied currents, 1900, 2100 and 2700 A, and a constant pressure of 20 MPa were employed as process conditions. The developed spark plasma sintering (SPS) finite-element model includes a moving-mesh technique to account for the contact resistance change due to sintering shrinkage and punch sliding. The effects of the heating rate on the microstructure and hardness were investigated in detail along the sample radius from both experimental and modeling points of view. The maximum hardness (2700 HV10) was achieved for a current of 1900 A at the core sample, while the maximum densification was achieved for 2100 and 2700 A. A direct relationship between the compact microstructure and both the sintering temperature and the heating rate was established.     

Physical Properties Important to Electrostatic and Non electrostatic Powder Transfer Efficiency in a Tumble Drum

ABSTRACT: Popcorn was oiled and coated in a tumble drum nonelectrostatically and electrostatically with sugar, cornstarch, salt, cellulose, maltodextrin, all-purpose flour, whole-wheat flour, or soy flour. Particle size, density, flowability, and chargeability were correlated to transfer efficiency using regression analysis. Of the various methods to measure chargeability, charge-to-mass and adhesion improvement were the most significant. For nonelectrostatic coating, small, dense, free-flowing powders were most efficient. Small, free-flowing highly charging powders were most efficient for electrostatic coating. Percent improvement was the highest for the least efficient powders. The greatest benefit with electrostatic coating was for low density, highly charging powders with no effect of size.     

日产1000t水泥熟料生产线的提产措施

通过对五级旋风筒下料管、回转窑转速、配料方案、物料稳定等四方面进行改进,达到提产目的。     

单孔护壁爆破数值模拟

运用LS-DYNA软件对单孔护壁爆破和切缝药包爆破进行了三维数值模拟,结果显示,由于PVC-U套管的存在,作用于孔壁的爆炸应力波峰值被显著削弱,降低率达到30%～46%,并推迟了其到达保留岩体孔壁时间.与传统的切缝药包爆破相比,保留岩体损伤更小.