Numerical characterization of a microscale solid-oxide fuel cell

In this study, a single unit of planar micro-solid-oxide fuel cell (μSOFC) is investigated numerically to evaluate the influences of flow channel design, oxygen composition, and thermal operating conditions on cell performance. Four flow channel designs are examined under the co-flow configuration: serpentine, double serpentine, rod bundle, and oblique rib. For all designs, the contacts areas of interconnect to electrodes are kept consistent to maintain the ohmic losses at the same level. To characterize the mass transport effects, there are three different compositions, 100% O₂, 50% O₂/50% N₂ and air, fed to the cathode inlet. Different thermal conditions, adiabatic and isothermal, are applied to the outer boundary of the μSOFC and the results are compared. The outcomes suggest that both thermal conditions and oxidant composition show remarkable influences on μSOFC performance. Under adiabatic conditions, the rise of cell temperature causes a decrease in reversible voltage, deteriorating the overall cell competence. When oxygen is diluted with nitrogen, local gas diffusion becomes dominant to the cathode reaction. Bulk flow, on the other hand, plays a minor role in cell performance since there is little deviation in the polarization curves for all flow channel designs, even at high current densities. For comparison, the flow visualization technique is employed to observe the transport phenomena in various flow channel designs. The flow patterns are found to resemble the concentration distribution, providing a useful tool to design μSOFCs.     

Al2O3对唐钢高炉炉渣性能的影响

针对唐钢近2年提高进口矿配比后，Al2O3含量升高对炉渣流动性带来的不利影响，对唐钢高炉的炉渣性能进行了试验研究。并结合国内同行业的生产实践经验，从理论上分析了炉渣中Al2O3及MgO的适宜含量范围，着重论述了唐钢所处冀东矿区条件下降低Al2O3的主要途径及适应高Al2O3炉渣的具体措施。     

Performance of a Yeast-mediated Biological Fuel Cell

Saccharomyces cerevisiae present in common Baker’s yeast was used in a microbial fuel cell in which glucose was the carbon source. Methylene blue was used as the electronophore in the anode compartment, while potassium ferricyanide and methylene blue were tested as electron acceptors in the cathode compartment. Microbes in a mediator-free environment were used as the control. The experiment was performed in both open and closed circuit configurations under different loads ranging from 100 kΩ to 400Ω. The eukaryotic S. cerevisiae-based fuel cell showed improved performance when methylene blue and ferricyanide were used as electron mediators, rendering a maximum power generation of 146.71±7.7 mW/m³. The fuel cell generated a maximum open circuit voltage of 383.6±1.5 mV and recorded a maximum efficiency of 28±1.8 % under 100 kΩ of external load.     

固体超强酸S_2O_8~(2-)/SnO_2-SiO_2催化合成环己酮1,2-丙二醇缩酮

采用沉淀-浸渍法制备了固体超强酸S2O28-/SnO2-SiO2,以它为催化剂催化环己酮和1,2-丙二醇合成了环己酮1,2-丙二醇缩酮;考察了带水剂种类及用量、酮醇摩尔比、催化剂用量、反应时间对产品收率的影响,并用正交实验对反应条件进行了优化。实验结果表明,适宜的反应条件为:n(环己酮)∶n(1,2-丙二醇)=1∶1.6、催化剂用量为反应物料总质量的2.0%、带水剂环己烷用量5.0mL、反应时间50min。在此条件下,环己酮1,2-丙二醇缩酮收率达到91.47%;催化剂的稳定性良好,在重复使用5次后环己酮1,2-丙二醇缩酮收率为82.20%,活性下降的主要原因为催化剂表面积碳和吸附了有机物;经傅里叶变换红外光谱和气相色谱质谱分析表明,产物为环己酮1,2-丙二醇缩酮,纯度为100%。     

Response surface methodology applied for Orange II photocatalytic degradation in TiO2 aqueous suspensions

BACKGROUND: Heterogeneous photocatalysis is influenced by a number of parameters involving synergistic effects; hence, an experimental strategy design that considers interactions between the main variables is needed. The response surface methodology was applied for the investigation of photodegradation of 20 mg L^?1 Orange II in aqueous solutions and for optimization of color removal efficiency. Preliminary studies were performed to identify the parameters to be selected for optimization. RESULTS: The input variables considered for experimental design were: solution initial pH, oxidizing agent (H₂O₂) initial concentration and UV‐A irradiation time. The multivariate experimental design allowed the development of a quadratic response surface model to be used for the prediction of color removal efficiency over the full range of the experimental region. Under the optimum conditions established in the region of experimentation (pH = 6.9, [H₂O₂]₀ = 183 mg L^?1 and t = 32 min), a 100% color removal efficiency was obtained in experiments. CONCLUSIONS: It was found that the variables considered have important effects on color removal efficiency. The results demonstrate that the use of experimental design strategy is indispensable for successful investigation and adequate modeling of the process because the interdependence of the reaction parameters cannot be neglected. Copyright © 2008 Society of Chemical Industry     

On modeling the design of cellular manufacturing systems

A new optimization model is discussed for the design of cellular manufacturing systems. It is based on an integer programming formulation that updates some other models by eliminating redundant machine assignment and cost coefficients dependent on cell configuration. To reduce computational burdens, a simplified integer programming model and a decomposition algorithm are proposed. Several computer solutions were performed to evaluate the performance of the new model. The computational results are discussed.     

Structural modelling of coprecipitated VTiO catalysts

A statistical study of the particle shape and size of pure V₂O₅ and TiO₂, and samples of coprecipitated V₂O₅---TiO₂ catalysts with different V/Ti ratios, has been performed. They were also characterized by XRD, EDAX, SEM and XPS. The results showed that pure vanadium pentoxide is compose by large square or needle-shaped particles, while pure titanium dioxide has small and rounded ones. VTiO samples presented an area and shape, depending on the V/Ti ratio.

These results and the spectroscopical characterization conducted to a particle model of the catalysts. Those VOTi samples with high V/Ti ratio would have large V₂O₅ crystals acting as support of a V/TiO₂ solid solution. In contrast, those samples with a low V/Ti ratio, would have the solid solution supporting vanadium pentoxide crystals.     

Al2O3—TiB2陶瓷刀具材料的高温氧化及其对刀具耐磨性能的影响

研究了Ａｌ２Ｏ３－ＴｉＢ２陶瓷刀具材料在１０００℃下的氧化行为，用ＸＲＤ、ＳＥＭ分析了氧化后的相组成及显微结构。结果表明：Ａｌ２Ｏ３－ＴｉＢ２陶瓷材料在１０００℃空气中氧化增重符合抛物线规律；随ＴｉＢ２含量的增加，该材料的抗氧化能力下降。     

2－重自补图论（Ⅲ）──计数理论

文中解决了２－重自补图的计数问题，获得了具有ｐ个顶点的２－重自补图的数目是其中Ｚ（Ａ）表示置换群Ａ的圈指标，Ｓ￣（２）＿ｐ表示ｐ次对称群的对群．