一种有效减少ADI-FDTD数值色散的方法

ADI—FDTD算法的数值色散效应较为明显，本文的研究表明一种通过添加各向异性媒质来修正相速误差，从而减少FDTD数值色散的方法，同样适用于ADI-FDTD，且收效更为显著。数值运算结果证明该方法能够简单有效地去除较宽频带范围内的色散。     

Collection Conduits Including Subsurface Drains

Numerous types of pipes and channels with spatially increasing flows in environmental engineering applications are identified by type and function and referred to as collection conduits. An overview of methods for designing and analyzing collection conduits is provided. Full conduits with nonuniform and uniform inflow are first considered. Dimensional analysis is then employed to demonstrate the relationship between variables for open channels; that leads to the identification of possibilities for generalized numerical solutions. Prior collection conduit applications are discussed within the framework of the dimensional analysis (which also pertains to some constant-flow applications). A previously unpublished generalized numerical solution for rectangular collection conduits is presented. Subsurface drains are addressed with particular emphasis, including the use of numerical methods to develop a new generalized chart and relation to other design methods. Among the important conclusions for subsurface drains is that the somewhat common practice of using Manning’s equation alone for such problems is not generally adequate. Examples and practical design suggestions are included, and the use of computer-based numerical methods is discussed more generally.     

阴,阳离子聚合物地层内凝胶化改善水驱效果的研究

研究了一杆阴离子聚合物（Ａｃ５３０）和一种阳离子聚合物（Ｍｂ５８１）在水溶液中形成凝胶的条件和过程、凝胶化学结构、形态、稳定性和力学性能。在模拟地层的二维微观模型内观测了两种聚合物驱替渗流、相逼、形成凝胶、凝胶封堵大孔道的机理。在亲水填砂模型内测定了阴、阳离子聚合物凝胶体系降低渗透率的能力。     

An explicit finite difference method for finite-time observers

In this paper we present a numerical method for estimating the current state of a nonlinear control system. We use finite differences to discretize a modified version of the finite-time observer equations in James. The discretized equations are simple and easily programmed. The convergence and accuracy of the scheme is proved, and the scheme enjoys a number of important properties: availability of rate of convergence estimates, good robustness characteristics, and the ability to handle certain types of discontinuities in the observations. The major disadvantage is that the number of grid points required increases exponentially with the number of state dimensions.     

PS,LS和煤油体系的界面张力

本文以石油磺酸盐(PS)、木质素磺酸盐(LS)和煤油体系为对象,研究了PS/LS比、盐度、醇、Na_2SiO_3及聚合物对体系界面张力(IFT)的影响,探讨了PS与各组分间的相互作用,结果发现,在一定盐度和混合醇(正丁醇+异丙醇)浓度下,PS/LS>0.3/0.7时,体系可形成中相微乳液,IFT值达1×10~(-3)mN/m左右;LS和聚合物的存在使IFT升高;在表面活性剂驱油体系中,可用廉价的LS部分代替PS。     

广东省伴生放射性矿资源利用过程辐射水平调查

为加强伴生放射性矿物资源开发利过程中放射性环境管理 ,防治放射性污染 ,对广东省几个大型伴生矿(包括稀土矿、钽铌矿和铅锌矿 )资源利用 (开采、冶炼、加工 )过程中天然放射性核素的污染现状进行了调查。调查结果表明 :稀土矿中独居石 ,天然放射性核素含量最高 ,2 3 8U、2 3 2 Th、2 2 6Ra的含量分别为 3.5 1× 1 0 4、1 .74× 1 0 5、4 .8×1 0 4Bq/kg,其冶炼废渣中核素的含量分别为 5 .1 0× 1 0 5、6 .38× 1 0 6、1 .5 2× 1 0 6Bq/kg。稀土选冶厂周围陆地环境 γ射线的空气吸收剂量率比一般地区的高。     

Influence of the intrinsic layer characteristics on a-Si:H p–i–n solar cell performance analysed by means of a computer simulation

In this paper a set of one-dimensional simulations of a-Si:H p–i–n junctions under different illumination conditions and with different intrinsic layer are presented. The simulation program ASCA permits the analysis of the internal electrical behaviour of the cell allowing a comparison among the different internal configurations determined by a change in the input set. Results about the internal electric configuration will be presented and discussed outlining their influence on the current tension characteristic curve. Considerations about the drift–diffusion and the generation–recombination balance distributions, outlined by the simulation, can be used to explain the correlation between the basic device output, the i-layer characteristics (thickness and DOS), the incident radiation intensity and photon energy.     

Numerical simulation of typical contact situations of brake friction materials

In the paper, a model typical for contact situations of automotive brakes is established based on the method of movable cellular automata. The processes taking place at local contacts in an automotive brake system are analysed. Based on microscopic and micro-analytical observations, the following contact situations were simulated: (i) a couple of ferritic steel against pearlitic steel, both covered by an oxide layer mixed with graphite nanoparticles and (ii) the same situation but without oxide layers. The results of calculated mean coefficients of friction of the oxide-on-oxide contact correspond well to expected values for a real braking system, whereas steel-on-steel contact are twice as high. This allows one to make some conclusions; for example, oxide formation will take place more quickly than friction layer elimination, and finally this is responsible for the stabilisation of the coefficient of friction.     

Analysis of Multiphase Flow and Heat Transfer: Pressure Buildup in an Unsaturated Porous Slab Exposed to Hot Gas

This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab.     

铣制三元流叶轮时产生误差的原因分析及解决方法

对在五坐标数控加工中心上铣制三元流叶轮时出现的叶轮附面尺寸误差问题，进行了详细分析，并提出了问题的解决方法，有效地避免了加工中产生的超差。