泡沫钢的制备及压缩吸能特性

为制备高强轻质泡沫钢吸能材料,本文以430L不锈钢粉为原料、CaCl₂为造孔剂,采用粉末冶金烧结-溶解法制备了孔隙率为64%~80%,孔径1~4 mm的泡沫钢.利用SEM和XRD对试样进行微观组织结构分析,并对试样进行轴向准静态压缩测试,分析讨论了孔隙率和孔形对泡沫钢压缩变形行为和吸能特性的影响,以及变形过程中孔结构变形和坍塌机理.研究表明：泡沫钢孔结构呈近球形且分布均匀,孔之间通过孔壁上的微孔形成有效连通.在压缩变形过程中,变形区首先发生在孔形不规则且孔壁较薄处,后诱发周围孔变形并形成多个变形带.泡沫钢试样压缩屈服平台应力随着孔隙率的增加而减小,当孔隙率为64.81%~78.82%时,其对应的屈服平台应力为59.37~17.04 MPa.在孔隙率相同的条件下,孔形为近球形的泡沫试样,其屈服平台应力远高于孔形不规则的试样.当应变量为40%时,孔隙率为64.81%~78.82%的泡沫钢,其单位体积的能量吸收值为23.92~7.32 MJ/m³,约为泡沫铝的5~7倍.4种不同孔隙率泡沫钢样品的理想吸能效率(I)均达0.85以上,表明泡沫钢可以作为一种理想的吸能材料.     

Cyclic Nanoindentation for Local High Cycle Fatigue Investigations: A Methodological Approach Accounting for Thermal Drift

Cyclic nanoindentation allows characterizing the influence of single phases and their interactions on fatigue mechanisms. Herein, a method for high cycle fatigue testing by nanoindentation is presented. By combining high- and low-frequency indentation modes, high cycle numbers are achieved while obtaining sufficient data points to reconstruct force–displacement hysteresis loops. A challenge is the stochastic course of thermal drift which is addressed by measuring drift rate in regular low-force holding segments. Drift rates are used to correct the displacement values, yielding reproducible cyclic deformation data as it is shown for two very different materials, a ductile metal and a brittle ceramic.     

Thermodynamic studies on the complete phase diagram of aqueous two phase system containing polyethylene glycol dimethyl ether 2000 and di-potassium hydrogen phosphate at different temperatures

The liquid-liquid equilibrium of polyethylene glycol dimethyl ether 2000 (PEGDME₂₀₀₀)+K₂HPO₄+H₂O system has been determined experimentally at T=(298.15,303.15,308.15 and 318.15) K. The liquid-solid and complete phase diagram of this system was also obtained at T=(298.15 and 308.15) K. A nonlinear temperature dependent equation was successfully used for the correlation of the experimental binodal data. Furthermore, a temperature dependent Setschenow-type equation was successfully used for the correlation of the tie-lines of the studied system. Moreover, the effect of temperature on the binodal curves and the tie-lines for the investigated aqueous two-phase system have been studied. Also, the free energies of cloud points for this system and some previously studied systems containing PEGDME₂₀₀₀ were calculated from which it was concluded that the increase of the entropy is the driving force for formation of aqueous two-phase systems. Additionally, the calculated free energies for phase separation of the studied systems were used to investigate the salting-out ability of the salts having different anions. Furthermore, the complete phase diagram of the investigated system was compared with the corresponding phase diagrams of previously studied systems, in which the PEGDME₂₀₀₀ has been used, in order to obtain some information regarding the phase behavior of these PEGDME₂₀₀₀+salt+water systems.     

改良BBS法评价聚氨酯发泡催化剂

改良BBs法用光电法测发泡高度-时间曲线,用机械手完成投掷钢球动作,过程用微机控制。本文对此法测得的三乙胺、四甲基乙二胺、二甲基乙醇胺、双(二甲基氨基乙基)醚、三乙烯二胺等催化剂在聚氨酯软质泡沫塑料形成过程中的胶化-发泡曲线进行了讨论,并评价了它们的催化特性。改良BBs法与手工BBs法相比,具有检测精度高,样本采集点多的优点。     

Oxidation behaviors of Ni-Cr-Al superalloy foams at 1 000 ℃ in air

The oxidation behaviors of Ni-16Cr-xAl （x=4.5%, 9.0%, mass fraction） superalloy foams in air at 1000℃ were investigated. The effects of AI content on the resistance to high temperature oxidation were examined. The oxidation mechanisms of the foams were discussed. The results show that the resistance to the oxidation of the Ni-16Cr-xA1 based alloy at 1 000 ℃ increases with the content of A1 increasing from 4.5% to 9.0%. Complex oxide products are formed on the surface of the superalloy foams after the oxidation. Cr203 and A1203 are the predominant oxides for the scales of the foams with 4.5% A1 and 9% A1, respectively. Excellent high temperature oxidation resistance and superior pore conformation stability for the Ni-16Cr-xA1 based superalloy foam with 9% A1 can be mainly attributed to the formation of relatively continuous and protective A1203 oxides on the surface of the foam.     

泡沫玻璃窑炉温度控制系统的设计与应用

针对泡沫玻璃生产线窑炉温度控制的工艺要求,设计并应用了P L C温度控制系统、P I D控制算法。现场应用表明,该系统运行稳定可靠,设计先进,界面友好,控制精度高,具有较高的实用价值,从而保证了产品的质量,降低了能耗,提高了企业竞争力。     

The relationship between thermal decomposition properties of titanium hydride and the Al alloy melt foaming process

Using a new temperature programmed decomposition (TPD) theory and related experimental technique, a set of thermal decomposition kinetics equations of titanium hydride can be acquired by separating and simulating its TPD spectrum. According to these equations, the relation curve of decomposition quantity and time for titanium hydride at temperature of 940 K is obtained and the result coincides well with the Al alloy melt foaming process, which provides a scientific basis for controlling the Al alloy melt foam and then the Al alloy foams with different pore structure are successfully prepared.     

石墨炉原子吸收测定化探样品中痕量金的研究

采用以王水分解样品,泡沫塑料富集,硫脲解脱,石墨炉原子吸收分光光度计测定微量金。研究了测定时干燥温度和时间的选择,原子化温度和时间的选择,灰化温度和时间的选择,以及王水体积分数对吸附效果等条件对测定结果的影响。该方法检出限为0.2×10-9,经国家一级分析标准样品验证,结果与标准值相符。     

低能X射线吸收法测量泡沫材料密度

文章介绍为适应惯性约束聚变(ICF)靶材料研究而发展的一种密度测量方法。通过测量X射线经靶材料吸收前后的强度变化,可较为精确地计算出待测样品的密度。用于泡沫材料密度测量的X射线源是特制的激发源。