泡沫微晶玻璃的研究进展

概述了泡沫微晶玻璃的性能及应用,综述了泡沫微晶玻璃的研究进展,并对泡沫微晶玻璃的发展方向进行了展望。     

由沥青制备多孔炭的工艺研究

采用沥青加发泡剂加炭黑制备了孔结构较好的多孔炭材料，分析和讨论了该工艺中沥青、发泡剂及炭黑的作用和影响，对多孔炭材料进行了力学性能测试和微观电镜观察分析，探讨了其可能的应用前景。     

不同粒径可膨胀石墨无卤阻燃高密度硬质聚氨酯泡沫塑料研究

采用高速混合破碎机对可膨胀石墨（EG）进行处理，制得不同粒径的EG。考察了不同粒径EG填充的硬质聚氨酯泡沫塑料（RPUF）的微观形态，研究了EG对于RPUF燃烧行为的影响。结果表明：EG的粒径越小，其在聚氨酯体系中的分散就越困难；20％未经处理的EG粒子（EG0）填充的RPUF氧指数为39．5％，比未填充的RPUF氧指数提高了近一倍，而经过13min破碎的EG粒子（EG13）其氧指数仅为23．5％，与纯RPUF的氧指数在同一水平；水平垂直燃烧结果可进一步验证氧指数结果，当EGO填充量超过10％时，RPUF燃烧已经达到了V-0级，而RPUF／EG13因其阻燃性能较差只能用水平燃烧分级。由此可见，EGO可有效提高RPUF的阻燃性能，而EG13对RPUF的燃烧性能几乎没有影响；研究同时提出了不同粒径EG无卤阻燃高密度硬质聚氨酯泡沫塑料的阻燃机理。     

制浆造纸工业用消泡剂的开发及应用进展

制浆造纸工业生产过程中不可避免会产生泡沫,泡沫控制不当会严重影响制浆造纸工艺条件的执行以及设备的正常运转,导致产品产量和质量降低,而控制泡沫最直接有效的措施是添加合适的消泡剂.该文介绍了制浆造纸工业生产中泡沫的产生和稳定机理,泡沫对制浆造纸工业生产过程和产品质量的影响,并针对制浆造纸生产中制浆、抄纸、涂布和脱墨等工段泡沫特性和消泡要求,综述了制浆造纸用消泡剂的发展历程、各工段消泡剂种类和性质,介绍了消泡剂的研制开发和实际应用成本及使用效果等,并对制浆造纸用消泡剂的发展进行了展望.     

Rheological properties and foam processibility of precured EPDM

EPDM foam was prepared by dynamically vulcanizing EPDM compound in a HAAKE rheometer firstly, then mixing the partially precured EPDM compound with a blowing agent and a sulfur vulcanizing system on a two roll mill. The compound was extruded through a cold feed extruder, and the extrudate was foamed in a circulating hot air oven. EPDM compound was vulcanized partly in the HAAKE rheometer, the final torque increases with increasing sulfur content. Rheological measurement shows the dynamic storage modulus, the loss modulus, and the complex viscosity of precured EPDM compound increase with increasing sulfur content. Then the partially precured EPDM compound was compounded with a blowing agent and a sulfur vulcanizing systems, Rheometric measurement shows that the rate of vulcanization of partially precured EPDM compound is not affected by the precure. The blowing results show that the foam processibility could be improved and the expansion ratio increases in the same processing condition for optimum partially precured EPDM compound, which indicates the optimum crosslink density for EPDM could enhance the efficiency of blowing agent AC. SEM shows that the foam articles have a closed‐cell structure with few open cells, and the large cells inlay among the small cells. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3387–3394, 2006     

酚醛树脂改性聚氨酯硬质泡沫塑料的研究

在多元醇中掺入甲阶酚醛树脂，与异氰酸酯反应，可以获得具有PF阻燃性和PU绝热性能的PF／PU共聚硬质泡沫塑料。介绍了甲阶酚醛树脂制备方法，并对其合成工艺、反应条件控制等进行了较详尽的探讨。     

挤出机各段温度对开孔型橡塑共混材料性能的影响

研究开孔型橡塑共混材料在不同挤出加工工艺中结构形态及力学性能的变化规律。结果表明，挤出机的机头温度应稍高于发泡剂的分解温度，均化段温度要设在发泡剂分解温度区的低温段，在挤出加工工艺中，要特别注意挤出机均化段温度及机头温度的设定，温度设定不好会使发泡剂无法发挥作用。     

Hydraulic resistance of rigid polyurethane foams. II. Effect of variation of surfactant,water, and nucleating agent concentrations on foam structure and properties

Hydraulic resistance of rigid polyurethane foams to penetration by water at high pressures is studied in this work in the context of buoyancy applications. Micron sized silica particles are used as nucleating agents. The effect of the variation of the concentrations of the surfactant, water, and nucleating agent on cell structure, closed cell content, and compressive modulus, is examined. Foams have densities in the range of 145 to 165 kg/m³. At a particular water concentration, with increase in the concentration of the surfactant, the window area of the cells becomes smaller and the hydraulic resistance of the foam increases. A cell window is the lamella of the foam material that separates two adjacent cells. With increase in the concentration of water keeping surfactant concentration constant, the average window area remains almost the same but the cell window area distribution becomes wider and the hydraulic resistance of the foams decreases. Foams made with silica have smaller cell windows but lower hydraulic resistance than that of the foams made without silica. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2830–2837, 2004     

涤纶废产物用于制备聚氨酯泡沫塑料

将涤纶废产物用二甘醇和三元醇经酯基转移合成齐聚酯多元醇，并用其制备聚氨酯硬质泡沫塑料。该泡沫塑料具有良好的力学性能，且随着齐聚酯多元醇平均官能度的影响，力学性能随之提高；由于齐聚酯多元醇中芳香族基团含量高，泡沫塑料的铖一明显高于普通聚氨酯泡沫塑料。     

热塑性硬质聚氨酯泡沫在汽车顶内饰中的应用

概述了汽车顶内饰用热塑性聚氨酯硬质泡沫塑料进展状况，介绍了硬泡及顶内饰成型方法，对影响该硬泡性能的一些因素进行了讨论。指出该顶内饰已批量生产。