Influence of the Preheat Treatment on the Microstructure and Properties of X37CrMoV5-1 Steel

The technological properties of the hot-work tool steels depend on their microstructural quality induced by the production process and the heat treatment. One of the frequently applied methods to improve microstructure is preheat treatment. The treatment of carbonitriding X37CrMoV5-1 steel has been investigated in fluidized bed furnaces. Thickness and phase composition have been conducted using optical microscopy Neophot 32 and scanning microscopy, JEOL 5400, after etching in nital.     

A novel technique to prepare LiNbO3 at low temperature

Fresh niobium hydroxide was first precipitated from NbF₅ solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 °C) produced pure ultrafine single phase LiNbO₃ (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM).     

Nonlinear discrete-time models: state-space vs. I/O representations

This paper compares state-space and input–output realizations for nonlinear discrete-time dynamic models. For linear models, these two realizations are essentially equivalent and their structures are closely related, but these statements do not hold for nonlinear models. We illustrate this point with simple, realistic examples for which only one of the two realizations exists or for which both exist but their structures are profoundly different. Overall, the main point of this paper is the importance of the choice of realization in the development of nonlinear dynamic models.     

An investigation of the relation between the temperature dependences of the initial unbalance and the output signal of resistance strain sensor bridge circuits

The relation between the initial unbalance and the output signal of bridge circuits when acted upon simultaneously by the physical factor being measured and the temperature of the surroundings when the bridge is supplied from a voltage or current source is investigated. Analytic relations are obtained which explain the temperature dependence of the useful output voltage under external physical action. __________ Translated from Izmeritel’naya Tekhnika, No. 1, pp. 48–49, 2007.     

Effect of C/Ti ratio on the laser ignited self-propagating high-temperature synthesis reaction of Al-Ti-C system for fabricating TiC/Al composites

TiC/Al composite was successfully synthesized utilizing laser ignited self-propagating high-temperature synthesis (SHS) of Al-C-Ti system with the different C/Ti molar ratio. When the molar ratio of C to Ti is below 1:1 in the starting materials, in addition to fine TiC particulates, a large amount of Al₃Ti phase was found in the composites; however, when the molar ratio of C to Ti is 1:1 in the starting materials, the Al₃Ti phase was almost completely eliminated and the distribution of TiC particulates generally appeared to be more homogeneous throughout the products synthesized.     

理学SMX-10/11型X荧光光谱仪的改进

对理学SMX-10／ll型X荧光光谱仪真空系统、样品定位系统及热交换器冷却水循环路径等易发生故障部位进行改进，并在11型仪器上增加了S元素分析通道。生产应用表明，改进效果良好，简化了分析工艺。降低了分析成本，提高了仪器的稳定性。     

X-Ray Measurement of Residual Stress in Plastic Bonded Explosives

The X-ray diffractive technology was adopted for tentative study of plastic bonded explosive. The datum of some new diffractive peaks in standard PDF cards were added. The effects of strain to interplanar distance and crystal size of the explosive were studied. The results show that grain size of plastic bonded explosive is decreasing with the increasing of the pressure, and the residual stress of the explosive is draw stress.     

XPS studies of directly fluorinated HDPE: problems and solutions

X-ray photoelectron spectroscopy (XPS) applied to the study of fluorinated polymer surfaces presents several problems related both to peak assignment and to degradation. In this work, we analyse extensively the question of XPS peak assignments in this kind of surfaces. We conclude that in this kind of surfaces using binding energy differences between fluorine and carbon is better than using absolute binding energies. Also a useful relation between fluorine photoelectron energy vs. polymer composition expressed through the atomic ratio fluorine/carbon (F/C) was found. A protocol for data treatment is proposed and applied to a XPS study of the degradation induced by X-ray on high-density polyethylene surfaces modified by direct fluorination. Results obtained for the degradation, namely the atomic ratio F/C obtained by two different methods, combined with angle resolved X-ray photoelectron spectroscopy (ARXPS) were used to study the fluorine concentration profile in depth, producing self-consistent results.     

近10年中国润滑脂产量与品种构成的发展

基于对中国27个润滑脂生产厂的调查统计结果，综述了1992～2001年10年间中国润滑脂产量、生产规模、品种结构及包装形式的发展变化情况，展望了今后的发展趋势。     

Combined PIXE and SEM study of the behaviour of trace elements in gel formed around implant coated with bioactive glass

Bioactive glasses are used as coating biomaterials to facilitate anchorage of metallic prostheses implanted into the body. The aim of this work is to study the behavior of gel formed in contact with alloys and BVA and BVH bioactive glasses implanted. Cylinders of metallic implants composed by Ti, Al and V, are coated with bioactive glass. Three sheep were implanted for different time length: 3, 6 and 12 months in the femoral epiphysis. Results obtained with particle induced X-ray emission and scanning electron microscopy show that BVA coating induces a better contact between the metallic implant and bone. On the other hand, BVH coating prevents corrosion from the metallic implant.