Kinetics of phenol oxidation in a trickle bed reactor over active carbon catalyst

The wet air oxidation of phenol over a commercial active carbon catalyst was studied in a trickle bed reactor (TBR) in the temperature and oxygen partial pressure ranges of 120–160 °C and 0.1–0.2 MPa, respectively. The performance of the active carbon was compared in terms of phenol and COD destruction. The weight change of active carbon due to reaction was also measured. Finally, oxic phenol adsorption isotherms were assessed in batch conditions at 25, 125 and 160 °C. In order to use the conversion data obtained from the TBR for a kinetic study, special care was taken to check the kinetic control in the TBR experiments. Several kinetic models including power law or Langmuir–Hinshelwood expressions were considered to describe the catalytic oxidation of phenol over active carbon. The simple power law model with first order dependence on both phenol and oxygen concentration predicted satisfactorily the experimental data not only over the entire range of operating conditions studied, but also outside its validity range. Copyright © 2005 Society of Chemical Industry     

Study on phase behavior–impact strength relationship of unsaturated polyester/polyurethane hybrid polymer network

The phase behavior of a hybrid polymer network (HPN) composed of poly[(propylene glycol maleate)-co-(propylene glycol phthalate)] crosslinked with styrene and polyester–urethane crosslinked with methylene-bis-ortho-chloroaniline was examined. The correlation between phase separation and impact strength of the HPNs is discussed. The composition of HPNs has an effect on their properties.     

适用于LED显示屏或照明工程的异步控制卡DS2000-M1

DS2000-M1是高性能、开放式的LED控制系统,本文从软硬件两方面简述其设计原理。     

透水性沥青面层材料设计新法及应用

本文提出了一种根据主骨料空隙率设计透水性面层沥青混合料级配的新方法，根据这一方法设计的透水性沥青面层具有良好的路面使用功能，应用前景广阔。     

瓶组气化站的建筑、结构设计要点

瓶组气化站的建筑，结构设计关系到安全，满足使用要求和投资的大小，本文根据多年的实践和最新的有关设计规范的要求，阐述瓶组气化站建筑，结构设计的要点。     

High temperature low cycle fatigue

Fatigue at high temperature is a complex phenomenon as it is influenced by a number of time-dependent processes which become important at elevated temperatures. These processes include creep, oxidation, phase instabilities and dynamic strain ageing (DSA), acting either independently or synergistically influence fatigue behaviour, often lowering the fatigue life. Current design approaches employ linear summation of fatigue and creep damage with suitable factors on permissible damage to take care of uncertainties in interaction between cyclic and time-dependent processes. It is, therefore, important to develop a deeper understanding of the processes that occur during high temperature fatigue so that realistic life predictions could be made. Results on the high temperature fatigue behaviour of austenitic stainless steels, ferritic steels and nickel base alloys are presented here. The important mechanisms of interaction of high temperature time-dependent processes with fatigue under various conditions are discussed in detail. Emphasis is placed on cyclic stress response, fatigue life, deformation substructure and fracture behaviour. This is followed by a review of important life prediction techniques under combined creep-fatigue loading conditions. Life prediction techniques considered here include linear damage summation, strain range partitioning, ductility exhaustion approach, frequency modified and frequency separation methods, techniques based on hysteresis energy and damage rate models, and methods based on crack-cavitation interation models.     

Enhanced Oil Recovery: The Synthesis of Anthraquinone [1, 2-C] Alkylisoxazole

Anthraquinone [1, 2-C] methylisoxazole is synthesized from 2-ethylanthraquinone through nitration and treating with oleum. The different methods of 2-ethylanthraquinone nitrated were discussed. The optimum conditions were determined. The structure of the product was confirmed by MS and ¹H NMR.     

Vegetation Change in Great Lakes Coastal Wetlands: Deviation from the Historical Cycle

Water-level change is integral to the structure and function of Great Lakes coastal wetlands, and many studies document predictable relationships between vegetation and water level. However, anthropogenic stressors, such as invasive species, land-use change, and water-level stabilization, interact to shift the historical cycle (of native vegetation migration up- and down-slope) toward dominance by invasive Typha species. Knowing from earlier studies that water-level stabilization alters the historical vegetation cycle, we asked if similar shifts can occur where water levels are not stabilized. Using historical aerial photographs of three coastal wetlands (in Lake Michigan's Green Bay, Wisconsin), we determined that habitat dominated by Typha species has expanded to eliminate wet meadow habitat. Between 1974 and 1992, linear regressions showed strong, significant relationships of both meadow area (R² ≥ 0.894; p < 0.02) and marsh area (R² ≥ 0.784; p < 0.05) to water level in all three wetlands. In 2000, meadow area was below that predicted by the historical pattern due to the landward advance of marsh habitat during a year of decreasing water levels. In the same period, land use in the wetland watersheds converted from agriculture to urban. Urbanization and the replacement of native Typha latifolia by the invasive hybrid Typha xglauca may have overwhelmed the beneficial impact of water-level fluctuation. The documentation of vegetation shifts, as herein, is an essential step in the process of preserving and restoring ecological integrity.     

Synfuel development impacts— econometric modelling and policy analysis

The prospects for rapid near-term development of a synfuel industry in the USA have decreased, due to depressed world oil prices, synfuel project cost overruns, and the lukewarm support of the Reagan administration. Nonetheless, socioeconomic and environmental impact analysis studies can provide valuable information for determining the regional welfare effects of proposed projects. The author discusses the results of a regional econometric analysis of the synfuel projects planned for Western Kentucky, which focuses on environmental impacts, and reveals the inevitable trade-offs that would accompany synfuel development. Some policy issues are briefly reviewed, especially that of efficient energy pricing.     

A new alloy design concept for austenitic stainless steel with tungsten modification for bipolar plate application in PEMFC

The feasibility of a new alloy design concept utilizing the principle of ‘tungsten bronze effect’ is critically evaluated for the development of metallic bipolar plates for proton exchange membrane fuel cell (PEMFC). An austenitic stainless steel (ASS) is modified with W and La to improve the stability of the passive film in an acidic environment as well as to reduce the contact resistance by the tungsten bronze effect. The experimental ASS containing W and La was evaluated in a simulated PEMFC environment of H₃PO₄ and H₂SO₄ solutions at 80 °C, and the electrical property was evaluated by performing a contact resistance test. The test results show that the ASS modified with W and La has good passive film stability for corrosion resistance and low contact resistance. The X-ray photoelectron spectroscopy (XPS) analysis clearly suggests the possibility of the tungsten bronze effect from the change in valency state of W⁶⁺ to W⁵⁺ in the passive film formed on the modified ASS. The feasibility of a new alloy design concept utilizing the ‘tungsten bronze effect’ is well demonstrated; however, more study is highly required for the development of metallic bipolar plates of PEMFC.