Fluorinated γ-alumina aerogels and xerogels: characterisation and catalytic behaviour

The porosity of -alumina-based materials is an important parameter affecting the extent of fluorination (aerogels > commercial -Al₂O₃ > xerogels) and, consequently, also the textural, acidic and catalytic properties of the final fluorinated materials. Only the highly fiuorinated aluminas having strong Lewis acidic sites catalyse the isomerisation of CHF₂CHF₂ to CF₃CH₂F.     

微波辐射磷钨酸催化合成环己酮1,2-丙二醇缩酮

在微波辐射下,以磷钨酸为催化剂,对以环己酮和1,2-丙二醇为原料合成环己酮1,2-丙二醇缩酮进行了研究.较系统的研究了反应物投料比、微波辐射功率、微波辐射时间、催化剂用量、带水剂用量诸因素对产品收率的影响.最佳反应条件为:环己酮为0.2mol,n(环己酮):n(1,2-丙二醇)=1.0:1.5,微波辐射功率600W,辐射时间16min,催化剂用量为反应物总质量的0.5%,带水剂(环己烷)15mL.在此条件下,环己酮1,2-丙二醇缩酮的产率可达82.0%.     

微波辐射对甲苯磺酸催化合成乙酸环己酯

以冰醋酸和环己醇为原料 ,环已烷为带水剂 ,对甲苯磺酸作催化剂 ,采用微波辐射技术 ,在常压下直接合成乙酸环己酯。最适宜反应条件为 :n(环己醇 )∶n(乙酸 ) =1 5∶1 0 ,对甲苯磺酸用量 0 2 0 g ,带水剂用量 5mL ,微波功率 5 95W ,辐射时间 15min ,产率达 97%以上     

微波辅助合成1-(3-羟丙基)-4-哌啶酮

以3-羟基丙胺和丙烯酸甲酯为起始原料,在微波辅助下进行Michael加成、Dieckmann环合和脱羧反应合成了1-(3-羟丙基)-4-哌啶酮.并对Michael加成、Dieckmann环合和脱羧反应的工艺参数进行了优化,通过核磁共振波谱对目标化合物和中间体的结构进行表征.得到的最优Michael加成工艺条件为:n(3-羟基丙胺):n(丙烯酸甲酯)=1.0:2.4,微波辐射功率为120 W,反应温度40℃,反应时间30 min.在该条件下制备3-[(2-甲氧羰乙基)(3-羟丙基)氨基]丙酸甲酯的收率为92.6％;在微波辐射功率为200 W下,Dieckmann环合反应和脱羧反应分别为20和25 min,以88.5％的收率得到1-(3-羟丙基)-4-哌啶酮;目标产物总收率为82.0％.     

Influence of untreated and novel electron‐beam‐modified surface‐coated silica filler on the thermorheological properties of ethylene–octene copolymer

We developed surface‐modified silica fillers by coating these with an acrylate monomer, trimethylolpropane triacrylate, or a silane coupling agent, triethoxyvinyl silane, followed by electron‐beam irradiation at room temperature. These were incorporated in an ethylene–octene copolymer rubber. Thermorheological studies of the unvulcanized ethylene–octene copolymer and its untreated and modified silica‐filled composites were done with a shear dynamic oscillating rheometer. Modification of the silica filler, especially via the silanization process followed by electron beam treatment, significantly reduced filler–filler networking as revealed from the log–log plots of storage modulus and complex shear viscosity, and its real component. The rheological complexity of the compositions was analyzed from a double logarithmic plot of the storage modulus and loss modulus. The results obtained from the master curves constructed on the basis of the time–temperature superposition principle and the activation energy calculated from the Arrhenius equation for the flow of above these compounds further supported these findings. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2453–2459, 2003     

2005年我国氯碱生产能力超高速增长

对截止2005年7月末我国氯碱装置的生产能力、2005年投产的装置、目前在建装置进行了介绍.国内大型氯碱生产装置、离子膜法装置在增多,但存在企业多、局部地区企业密集、产能增长过速的问题.     

Physicochemical properties of irradiated and loaded LDPE films with polyfunctional monomers

Polyfunctional monomers (PFMs), namely, trimethylol propane trimethacrylate (TMPTMA), trimethylol propane triacrylate, ethylene glycol dimethacrylate, and diethylene glycol diacrylate were blended with low‐density polyethylene (LDPE) and exposed to different doses of EB irradiation. Fourier transform infrared and ultraviolet and UV–vis spectroscopy of the unirradiated, irradiated, unloaded, and PFMs‐loaded LDPE films were studied under various irradiation doses up to 300 kGy. The degree of crosslinking and oxidative degradation, as measured by the spectroscopic parameters, were dependent on both the irradiation dose and the type of loaded PFMs. For all of the loaded monomers, the extent of crosslinking increased at different rates as a function of irradiation dose. TMPTMA monomer was the most efficient in enhancing the crosslinking of LDPE films compared to the other loaded monomers. However, the unloaded LDPE film showed the least extent of crosslinking. In addition, the EB‐radiation‐induced changes, such as trans‐vinylene formation, a decrease in vinyl and vinylidene unsaturation; and carbonyl double‐bond formation and change in crystallinity were correlated. The importance of these results on the prediction of the role of polyfunctional monomers in the production of crosslinked polymers is discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2025–2035, 2003     

玻璃钢件固化成型中变形现象的剖析

结合实例剖析由产品结构、成型工艺和工艺装备等主要因素影响的复合夹层结构玻璃钢件和实体玻璃钢件在固化成型中的变形现象，并指出了预防变形的各相应有效措施。     

Impact of H+ ion irradiation on Matrimid®. I. Evolution in chemical structure

Ion beam irradiation can be used to modify the structure and gas transport properties of glassy polymers. This is the first of two studies that focus on the impact of H⁺ ion irradiation on the structure and permeation properties of the polyimide Matrimid®. Specifically, the evolution in chemical structure after H⁺ irradiation over a range of fluences was analyzed using FTIR spectroscopy and dissolution studies. Although H⁺ ion irradiation at very low ion fluences induced little modification in the chemical structure, irradiation at relatively high ion fluences resulted in crosslinking of the irradiated films. The branched structure of the aliphatic methyl (CH₃) was the most sensitive to the H⁺ ion irradiation. The para‐disubstituted aromatic ring showed the strongest resistance toward ion irradiation and required fairly high doses to induce degradation. Two potential crosslinking mechanisms related to the degradation of the aliphatic methyl and the benzophenone carbonyl were presented. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2010–2019, 2003     

混合遗传算法求解应急抢修点选址问题

考虑设备应急抢修的时限要求和整个应急抢修系统的服务质量要求,采用0-1整数规划模型描述了应急抢修点选址问题,并针对该问题设计了一种混合遗传算法。在算法中使用启发式算法对种群中的不可行解进行修复,以保持种群在可行域内搜索,并采用近邻搜索算法改善种群中的最佳个体。算例计算的结果表明,该算法求得的结果要优于基于罚函数的遗传算法和采用简单修复算法的遗传算法。