乙烯裂解炉对流段局部结构设计改进

介绍了乙烯裂解炉对流段的结构功能,各部件局部结构的改善设计。     

二次电池电极基板用复合多孔金属材料的研究

介绍了一种复合金属多孔体的制备及其方法，首先以泡沫塑料为芯膜，经过导电化处理使其具有导电性，其次进行电沉积金属铁，再进行电沉积金属镍，经过热处理后可制备出复合金属多孔体。该复合金属多孔体用铁取代金属镍，其抗拉性能优于单质泡沫镍，同时可以降低制造成本，主要用于载体如电池电极。     

Metallurgical Investigation of a Prematurely Failed Concentric Reducer Tube Used in a Hot-Rolling Mill

A concentric reducer tube, which was a part of the top exit roughing hydraulic descaler in a hot strip mill failed prematurely under working pressure. A detailed metallurgical investigation comprising physical examination, optical microscopy, scanning electron microscopy, and electron probe microanalysis was carried out to find out the genesis of the failure. Physical examination revealed cracks located symmetrically around the circumference of the tube that ran along its full length, up to the weld beads at both ends. Optical microscopy of etched samples revealed a banded ferrite-pearlite structure and the existence of forging folds near the change-in-section(160° fillets). Cracks were found to initiate from these forging folds. No structural abnormalities were found in the weld beads and heat-affected zones.     

日产1000t水泥熟料生产线的提产措施

通过对五级旋风筒下料管、回转窑转速、配料方案、物料稳定等四方面进行改进,达到提产目的。     

Combustion of bulk density powder mixtures in a coflow of nitrogen gas: 3. The Ti-(Ti + 0.5C) layered system

Explored is the filtration combustion in Ti-(Ti + 0.5C) layered powder systems in a coflow of nitrogen gas. The presence/absence of nitrogen coflow through the layered system was found to drastically affect the character of wave propagation and structure/properties of product. The obtained data can be regarded as a basis for fabrication of new layered and composite materials in the mode of dynamic filtration combustion.      

Hydrogen production from methane in a dielectric barrier discharge using oxide zinc and chromium as catalyst

The hydrogen fuel cell is a promising option as a future energy resource; however, the nature of the gas is such that the conversion process of other fuels to hydrogen on board is necessary. Among the raw fuel resources, methane could be the best candidate as it is plentiful. In this experiment, the possibility of producing hydrogen with less carbon formation from methane by a dielectric barrier discharge (DBD) was investigated. Without the addition of a catalyst, the formation of hydrogen reached between 30% and 35% at methane residence time of 0.22 min and supplied powers in the range of 60-130 W. The hydrogen selectivity increased at higher supplied power, but the process efficiency, defined as a ratio of the produced hydrogen to the supplied power, decreased slightly. In order to boost the hydrogen production with less carbon formation, a mixed oxide catalyst of zinc and chromium was added to the reactor. It was shown that the production of hydrogen was ca. 40% higher than the non-catalytic plasma process.     

厦门市气源转换的技术分析

分析了气源转换时原有输配系统的管道、调压设备、计量设备、用气设备与天然气系统相适应的问题，提出了相应的措施。     

低工作温度的氧化钨气敏材料

本文报道了一种可以在１００℃左右工作的氢化钨气敏材料，它对氢气和一氧化氮有很高的灵敏度和良好的选择性，并可对空气中的一氧化氮进行探测     

管内覆丝网强化对流换热及阻力特性的实验研究

通过实验对管内覆丝网管进行了强迫对流换热和阻力特性研究。结果表明：管内覆丝网使换热明显增强，阻力也相应增长。菱形丝网对角线距离与平行边距离之比对换热效果有决定作用，丝网厚度对换热的影响比较小，而丝网网格的大小对换热几乎没有影响，在相同的泵功率和几何条件下，换热系数最大增加２１％。     

用COREX输出煤气生产直接还原铁

将Ｃｏｒｅｘ输出煤气用于直接还原铁（ＤＲＩ）的生产是该气体的最佳用途。该方案在技术上是可行的。其中ＣＯ２的脱除方法已成熟并有多种选择。据推断，煤气加热时不会产生严重析碳，所以不影响加热和还原。ＣＯ２脱除量大、产品碳含量高、还原速率下降及入口温度上升是还原工艺的主要特点。ＨＹＬⅢ工艺比Ｍｉｄｒｅｘ工艺更适于使用Ｃｏｒｅｘ输出煤气。用Ｃｏｒｅｘ输出煤气作还原气时能耗比使用天然气时高。