钢包烘烤装置的发展

概述了钢包烘烤的意义，钢包烘烤装置的进展。     

Feedback linearizing control of a fluidized bed reactor

The design of an adaptive nonlinear controller for the control of a fluidized bed reactor is derived by using exact linearization techniques. Reset action and parameter adaptation are used to make more robust the precise compensation of nonlinear terms, which is called for in the linearization technique. A nonlinear antiwindup mechanism is introduced to handle reset windup problem and to provide fast response without large overshoot. Simulation results show that the proposed adaptive controller guarantees good setpoint tracking. The developed estimation algorithm allows accurate estimation of the parameters for which the regressor component is not zero.     

钢锭零能少氧化均热轧制的研究

根据计算机的辅助分析,采用新的钢锭传搁、注后强制水冷却、垫铁脱模等工艺后,入炉钢锭的热焓已超过开坯轧制需要,利用普通均热炉代替钢锭保温车,可完全依靠到钢锭自身潜热与显热进行均热。对不同锭型与钢种采用经试验的最佳时间均热后再轧制,收与保温车均热钢锭直接轧制相同的效果。     

宽低温STN—LCD加热装置的研制

本文介绍了宽低温ＳＴＮ－ＬＣＤ加热装置的设计和制备方法，并对低温加热的实验结果进行了讨论和分析，相应的研究结果表明此法有利于拓宽ＳＴＮ液晶显示器的负温工作范围。     

多孔挡板流化床还原UO3反应器模型的研究

针对ＵＯ＿３的Ｎ＿２还原反应建立了多孔挡板流化床反应器模型。将多孔挡板床的每一级视为具有相似的流动状态，每一级的上、下段称为稀、密相段，分别用鼓泡床和活塞流模型描述。该模型的计算值与￠６３ｍｍ的多孔挡板床Ｈ＿２还原ＵＯ＿３的热态实验值能较好的吻合。还预计了还原温度、操作气速和挡板结构参数对固相转化率的影响，为该类反应器的工业设计、放大和优化提供了依据。     

Design and performance of large low-cost solar water heating systems

An analysis is presented for the monthly performance evaluation of a simple design low cost solar water heating systems. A sample of typical results is presented which confirms their suitability as solar heating systems for summer peacking or as solar preheaters for year around loads.     

多种采暖方式的特点及其选择

介绍了多种采暖方式．并对各种采暖的适用性、一次性投资、运行费用和对环境的影响作了对比，提出了选择的优先顺序，为房地产开发商和用户对于采暖方式的选择提供了参考。     

压水堆硼稀释事故的计算

一、概述核电厂压水堆的初始过剩反应性是通过控制捧、固体可燃毒物和溶解在主回路冷却剂中的硼酸等三种方式联合控制的。随着反应堆的燃耗和裂变毒物的积累,堆的过剩反应性不断减少,需要通过化容系统,控制硼酸的浓度来进行补偿。如果化容系统发生故障或操作员误操作,就会给回路注入无硼或低于规定浓度的补给水,给反应堆引入正反应性,造成硼稀释事故。按核安全法规的要求,应对换料、冷停堆、热停堆和启动等工况进行计算,并要求在这些     

Transient operation of a catalytic liquid-liquid plug flow reactor for kinetics measurements

A centrifugal partition chromatograph (CPC) was used as a liquid-liquid catalytic reactor for the isomerisation of hexen-3-ol into ethylpropylketone with a water soluble rhodium catalyst. Global mass transfer coefficients were measured and shown to depend on both the nature of the solute and the flow rate. Liquid-liquid partition isotherms were also determined with the CPC using elution chromatography. Finally, a reactor model was derived to account for the experimental results obtained both under stationary and transient (pulse) conditions. A parameter sensitivity evaluation is also presented.     

核孔膜生产线膜微孔制备工艺实验研究

本文介绍核孔膜生产线,重点描述了膜微孔制备工艺的实验研究。对于PC和PES膜,已得到32种工况下的扩孔公式,其形式为D=A+Bt,其中D——孔径,t——扩孔时间,A,B为特定工艺参数下的常数值.通过实验。得到了膜孔密度N与300~#核反应堆功率P、热柱辐照位置L的经验公式,即N=6.97×10~5×10~3×101~(1.18L).在本生产线上可生产最大幅面为3 140mm×240mm,孔径为0.04～10 μm的多系列多规格的核孔膜产品。