Practical method for generation expansion planning based on dynamic programming

This paper presents an efficient method which provides the optimal generation mix and the optimal generation construction process. The approximation method in which the dynamic programming technique and gradient method are combined is applied to determine the optimal generation mix with hydropower generation technologies. The successive approximations dynamic programming (SADP) technique, which is very suitable for high-dimensional multistage decision process problems, is used for obtaining the optimal generation construction process. The effectiveness and feasibility of the developed technique are demonstrated on a practical power system model which has five types of generation technologies including a hydropower generation technology.     

Community OR — Five Years of Organised Activities and Beyond

What has become known as Community Operational Research has been around in the UK for many years. The election of Jonathan Rosenhead as President of the UK OR Society in 1986–87 was the catalyst for bringing together and expanding activities which had been carried out largely by individuals working in isolation on a voluntary basis. The following five years have seen the establishment of the Community OR Unit at Northern College, the Centre for Community OR at Hull University and the Community OR Network, which supports the activities of volunteer OR workers across the UK. This paper reviews the range and types of work which have been undertaken by various practitioners. An assessment of the success of community OR is made and a number of issues which have arisen are discussed. Finally, given the diverse nature of community OR, its practice and practitioners, there is some discussion about the future of the area.     

超薄SiO2层的热生长

隧道小孔中超薄ＳｉＯ２的生长是ＥＥＰＲＯＭ电路制造的关键工艺之一。采用ＳＵＰＲＥＭ－Ⅲ工艺模拟程序对超薄ＳｉＯ２的热生长进行了工艺模拟，经过大量的工艺实验及优化，确定了超薄ＳｉＯ２的最佳生长条件，生长出的ＳｉＯ２性能良好，完全可满足ＥＥＰＲＯＭ研制的要求。     

Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel

Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel are performed. The sizes of a regenerative heat exchanger and a boiler are expected to be smaller for He than for Ar. The pressure loss of a working gas in a regenerative heat exchanger is reduced for He. The purification subsystem for He is expected to be more compact and economical than that for Ar; but a larger compressor is required for He than for Ar.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Estimation of fouling in a plate heat exchanger through the application of neural networks

Pasteurization is an important, if not the most important, process step in the packaging of milk. It is subject to alterations stemming from the variation in the temperature, pH and raw milk quality. The variability may manifest itself in changes in the formation of the deposit (fouling) in the pasteurization unit, such that there is a need for tools, both instrumentation and computational, to help in monitoring the process and keeping it on the desired course. In this paper we describe a practical procedure based on artificial neural networks (ANN) that allows prediction of the deposit thickness, the overall heat transfer coefficient and the critical time (the time that the unit has to be stopped for cleaning) for reducing the impact of fouling on such processes. The procedure determines when the cleaning operation is required once the system is under critical conditions of operations. A combination of fundamental studies and plant measurements were used for study of the operating conditions and thus evaluation of the trades‐offs between operating conditions and longer operating life span. The results are encouraging, enough to validate current operating industrial techniques. Copyright © 2005 Society of Chemical Industry     

管网保温层热经济寿命的决策方法

利用保温裸露因数的概念来反映保温层保温性能的变化，提出采用统一原则来建立适用于单元系统和复合系统保温层热经济寿命的数学模型，并通过实例证明在热经济寿命终了时更新保温层，可使系统的运行具有最大的经济性。     

压水堆核燃料循环的经济分析程序介绍

所开发的压水堆核燃料循环分析计算机经济程序包括12个子程序,代表着压水堆整个核燃料循环各种不同的工艺过程。本程序能算出压水堆核电站核燃料循环中燃料费用对发电成本的影响,给出各工艺过程对燃料成本的敏感度分析,并尽可能给出燃料循环中燃料材料及服务的价格数据.     

Temperature effects on the mass flow rate in the SBI and similar heat‐release rate test equipment

In various medium‐to‐large‐scale fire test equipments like the ISO room corner test (RC), and more recently, the single burning item test (SBI) the mass flow rate measurement of the combustion gases plays a key role in the determination of the heat‐release rate and smoke‐production rate. With the knowledge of the velocity profile and the temperature of the flow, the mass flow rate is obtained by measuring the velocity on the axis of the duct. This is done by means of a bi‐directional probe based on the pitot principle. However, due to the variation of the mean temperature and the temperature gradient in any cross section of the duct, introduced by ever changing combustion gas temperatures, the velocity nor the density profile are constant in time. This paper examines the resulting uncertainty on the mass flow rate. Copyright © 2006 John Wiley & Sons, Ltd.