Simulation of Economic Dynamics under Ecological Balance Conditions

A model of economic dynamics under stable ecological balance conditions is proposed. A methodology of construction of an optimal growth path is constructed for this model.     

Color characteristics of Cu-Zn-Al alloys

ＣＯＬＯＲＣＨＡＲＡＣＴＥＲＩＳＴＩＣＳＯＦＣｕ－Ｚｎ－ＡｌＡＬＬＯＹＳ￣①Ｌｉ，Ｂａｏｍｉａｎ；Ｚｈａｎｇ，Ｘｉｕｈｕａ（ＳｈｅｎｙａｎｇＩｎｓｔｉｔｕｔｅｏｆＧｏｌｄＴｅｃｈｎｏｌｏｇｙ，Ｓｈｅｎｙａｎｇ１１００１５）ＣＯＬＯＲＣＨＡＲＡＣＴＥＲ...     

Structural and electrical properties of brush plated ZnTe films

Zinc telluride thin films were deposited by the brush plating technique at a potential of −0.90 V (SCE) on conducting glass and titanium substrates at different temperatures in the range 30–90 °C. The films were polycrystalline in nature with peaks corresponding to the cubic phase. Direct band gap of 2.30 eV was observed. XPS studiers indicated the formation of ZnTe. Depth profiling studies indicated a uniform distribution of Zn and Te throughout the entire thickness. EDAX measurements were made on the films and it was found that there was a slight excess of Te. The carrier concentration was found to vary from 10¹⁴–10¹⁵ cm⁻³ with increase of substrate temperature. The mobility was found to vary from 5 to 60 cm² V⁻¹ s⁻¹.     

混凝土大坝导温系数反演及其随时间变化的规律

随着时间的推移,混凝土的导温系数将发生变化,为了了解参数随时间的变化规律,利用原型观测资料对导温系数进行分段反演,从而拟合出大坝混凝土导温系数随时间的变化规律.     

破片式战斗部优化设计技术研究

侧重研究了破片式战斗部装药外形的优化设计技术。提出了装药外形与破片飞散特性（如破片飞散角，分布带宽等）之间的数学描述；建立了圆弧和对数螺线装药外形母线与战斗部其他设计参数间的数学模型。在假定约束条件下，优化设计了破片了聚焦式战斗部的结构参数；静爆试验结果表明，破片分布与理论计算吻合较好。     

卷轴式贴标签机剥离机构的优化设计

探讨了用解析的方法解决压敏标签贴标签机的剥离刀口的优化设计问题，分别提出了剥离刀口处的张力功、摩擦功、弹塑性变形功和剥离功的计算模型，并对结果进行了讨论，结果表明，剥离刀口的曲率半径存在一个最优值，此值分别与纸带预张力、压敏胶的特性、标签的瞬时剥离宽度、底纸带特性等有关。     

Testing of electrochromic materials using symmetrical devices

“Symmetric materials” devices, where both electrodes are made of the same electrochromic materials, allow the in situ study of side reactions. Each transferred charge that is not used for the expected electrochromic reaction will cause a colour change in the whole symmetric device. Two electrochromic materials, WO₃ and IrO₂, are successively used to show how to obtain information about side reactions such as faradaic efficiency, reversibility and potential limits from the symmetric experiment. This in situ approach with a polymer electrolyte shows significant differences compared to results obtained with studies in aqueous electrolytes.     

轮式工程机械轮边减速器优化模型与方法

论述了重构轮式工程机械轮边减速器优化设计数学模型的必要性,给出了精确化的目标函数,全面化和准确化的设计变量、基于并行设计的约束条件;介绍了对优化解适用性评价的方法和手段。巧妙地解决了优化解中离散变量的圆整问题,提供了基于MATLAB的求解反渐开线函数的M文件。     

Polyaniline-multiwalled carbon nanotube composites: Characterization by WAXS and TGA

Polyaniline/carboxylated multi-walled carbon nanotube (PAni/c-MWNT) nanocomposites have been synthesized by micellar aided emulsion polymerization with various c-MWNTs compositions, viz., 0.5, 1, 5, and 10 wt %. The microcrystalline parameters such as the nanocrystal size (〈N〉), lattice strain (g), interplanar distance (d_hkl), width of the crystallite size distribution, surface weighted crystal size (D_s), and volume of the ordered regions were calculated from the X-ray data by using two mathematical models, namely the Exponential distribution and Reinhold distribution methods. The effects of heat ageing on the microcrystalline parameters of the PAni/c-MWNT nanocomposites were also studied and the results are correlated. The thermal stability and electrical resistivity of the PAni/c-MWNT nanocomposites were examined with thermogravimetric analysis (TGA) and a conventional two-probe method. The TGA data indicate that the thermal stability of the nanocomposites improved after the incorporation of c-MWNTs. The influence of temperature on the resistivity of the nanocomposites was also measured. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008