Investigation of flame spray synthesized La1-xSrxCoO3 perovskites with promotional catalytic performances on CO oxidation

To enhance the activity of catalysts for CO removal, the perovskite-type catalysts La_1-xSr_xCoO₃ (x = 0, 0.2, 0.4, 0.6, and 0.8) with different Sr²⁺ doping amount were synthesized by flame spray synthesis (FSS) method. The perovskite-type catalyst synthesized by FSS has a much larger specific surface area (SSA) than that prepared by other conventional methods. The SSA of catalyst increases with the increase of Sr²⁺ doping amount and the SSA of La_0.2Sr_0.8CoO₃ reaches 31.65 m²/g. Compared with other conventional methods, FSS method significantly improves the activity of catalyst and makes it close to the performances of catalysts with surface modification. The substitution of La³⁺ by Sr²⁺ promotes the generation of secondary phase Co₃O₄ and SrCO₃. The catalytic activity of La_1-xSr_xCoO₃ increases with the addition of Sr²⁺, which results from the increasing active sites and oxygen vacancies. Interestingly, La_0.4Sr_0.6CoO₃ performs the highest activity for CO oxidation and the CO conversion reaches 50% at 148.6 °C and 90% at 165.9 °C. The oxidation of CO over La_1-xSr_xCoO₃ catalyst may follow a combination of MvK and L-H mechanisms according to the experimental results of H₂-TPR. Moreover, the catalyst exhibits good catalytic activity in consecutive oxidation cycles. In consecutive oxidation experiments with La_0.4Sr_0.6CoO₃, the CO conversion reaches 50% at 168.8 °C and 90% at 197.8 °C in the eighth oxidation cycle. These results prove that FSS method can further improve the activity of catalysts and is suitable for the preparation of efficient catalysts.     

从7-ADCA生产过程中环境友好的回收苯乙酸

采用新工艺回收7-氨基-3-脱乙酰氧基头孢烷酸(7-ADCA)生产中产生的苯乙酸,并对苯乙酸回收过程中产生的废硫酸进行处理。采用硫酸(9 8%)洗涤二氯甲烷,硫酸与二氯甲烷适宜的体积比为1∶50,洗涤好的二氯甲烷中含苯乙酸4%。蒸馏出二氯甲烷,趁热向熔融苯乙酸中加入母液,降温析出苯乙酸。晾干的苯乙酸为白色鳞片状,含量大于99%,苯乙酸母液补充部分清水套用到下一批析出苯乙酸。废浓硫酸用芬顿试剂氧化,控制80℃氧化4h,双氧水和七水硫酸亚铁重量比为6∶1,废浓硫酸COD下降85%以上。氧化结束后向废硫酸中加入铁粉和双氧水,制得聚合硫酸铁。     

Tribological behaviour of a 3Y-TZP/Ta ceramic-metal biocomposite against ultrahigh molecular weight polyethylene (UHMWPE)

This study aims to evaluate the tribological behaviour of 3Y-TZP/Ta (20 vol%) ceramic-metal composites and 3Y-TZP monolithic ceramic prepared by spark plasma sintering (SPS) against ultrahigh molecular weight polyethylene (UHMWPE). According to the results of pin (UHMWPE)-on-flat wear test under dry conditions, the UHMWPE – 3Y-TZP/Ta system exhibited lower volume loss and friction coefficient than the UHMWPE – monolithic ceramic combination due to the presence of an autolubricating layer that provides sufficient lubrication for reducing the friction. Owing to the lubrication of the liquid media, under wet conditions obtained using simulated body fluid (SBF), similar behaviour is observed in both cases. Additionally, the ceramic and biocomposite materials were subjected to a low temperature degradation (LTD) process (often referred to as “ageing”) to evaluate the changes in the tribological behaviour after this treatment. In this particular case, the wear properties of the UHMWPE-biocomposite system were found to be less influenced by ageing in contrast to the case of the UHMWPE-zirconia monolithic material. In addition to their exceptional mechanical performance, 3Y-TZP/Ta composites also showed high resistance to low temperature degradation and good tribological properties, making them promising candidates for biomedical applications, especially for orthopaedic implants.     

Group sequential crossover trial designs with strong control of the familywise error rate

Crossover designs are an extremely useful tool to investigators, and group sequential methods have proven highly proficient at improving the efficiency of parallel group trials. Yet, group sequential methods and crossover designs have rarely been paired together. One possible explanation for this could be the absence of a formal proof of how to strongly control the familywise error rate in the case when multiple comparisons will be made. Here, we provide this proof, valid for any number of initial experimental treatments and any number of stages, when results are analyzed using a linear mixed model. We then establish formulae for the expected sample size and expected number of observations of such a trial, given any choice of stopping boundaries. Finally, utilizing the four-treatment, four-period TOMADO trial as an example, we demonstrate that group sequential methods in this setting could have reduced the trials expected number of observations under the global null hypothesis by over 33%.     

Effect of Biochar as Reductant on Magnetizing-roasting Behavior of Pyrite Cinder

The effect of biochar substituted for anthracite as reductant on magnetizing-roasting pyrite cinder was investigated.The key of magnetizing-roasting is the gasification reaction between reductants and CO2.Since biochar could react with CO2 more rapidly at lower temperature,the reactivity of biochar is better than that of anthracite.The gasification of biochar could produce reducing condition ofφCO/(φCO+φCO2)about 10%-20% between 700-800 ℃,which is in accord with the atmosphere and temperature of Fe2O3 reduction.So it is beneficial to the reduction of iron mineral of pyrite cinder.Compared with anthracite,biochar could decrease the roasting temperature from825 to 750 ℃ and roasting time from 20 to 15min,which shows that a better effect of magnetization could be obtained in the condition of lower temperature and shorter time.Using biochar as reductant,iron concentrate extracted from pyrite cinder as about 64%iron grade could be produced,and the recovery is over 90% under the condition of above 90% grinding particle less than 0.045 mm and magnetic intensity of 0.124-0.194 T.     

Application of Vis–NIR hyperspectral imaging in classification between fresh and frozen-thawed pork Longissimus Dorsi muscles

Fresh and frozen-thawed (F-T) pork meats were classified by Vis–NIR hyperspectral imaging. Eight optimal wavelengths (624, 673, 460, 588, 583, 448, 552 and 609 nm) were selected by successive projections algorithm (SPA). The first three principal components (PCs) obtained by principal component analysis (PCA) accounted for over 99.98% of variance. Gray-level-gradient co-occurrence matrix (GLGCM) was applied to extract 45 textural features from the PC images. The correct classification rate (CCR) was employed to evaluate the performance of the partial least squares-discriminate analysis (PLS-DA) models, by using (A) the reflected spectra at full wavelengths and (B) those at the optimal wavelengths, (C) the extracted textures based on the PC images, and (D) the fused variables combining spectra at the optimal wavelengths and textures. The results showed that the best CCR of 97.73% was achieved by applying (D), confirming the high potential of textures for fresh and F-T meat discrimination.     

一类两性分枝过程条件均值增长率的极限性质

本文主要研究随机环境中配对依赖人口数两性 Galton-Watson 分枝过程的条件均值增长率的极限性质．利用上可加函数的性质，得到配对单元平均增长率的极限性质和该过程条件均值的上界和下界．文中给出了关于过程条件均值增长率的两个序列，利用配对单元平均增长率的性质，获得了这两个序列的极限性质．随机环境中配对依赖人口数两性分枝过程比较复杂，本文的结论推广了现有的研究成果．     

Decay Rate Kinetics of Ozone Gas in Rice Grains

The present study was carried out to evaluate the effects of ozone on rice grains for the following three conditions: saturation time, decay rate, and half-life of ozone. Experiments were performed in different bed thicknesses (5 and 10 cm) and moisture content (11.4 and 14.2% wb) at atmospheric conditions. The lowest saturation time of ozone was 119 min, with the concentration of 516 ppm for rice grains ozonated at 5-cm bed thickness with 11.4% (wb) moisture content. The decay rate kinetics of ozone obtained were consistent with a first-order model. Regarding the half-life of ozone, the lowest value obtained was 6.78 min for rice grains ozonated at 10-cm bed thickness with 14.2% (wb) moisture content.     

Improved formic acid oxidation using electrodeposited Pd–Cd electrocatalysts in sulfuric acid solution

In the present research, nanostructured Pd–Cd alloy electrocatalysts with different compositions were produced using the electrodeposition process. The morphology of the samples was studied by scanning electron microscopy analysis. Also, the elemental composition of the samples was determined by energy-dispersive X-ray spectroscopy and elemental mapping tests. Tafel polarization and electrochemical impedance spectroscopy methods were employed to determine the electrochemical corrosion properties of the synthesized samples in a solution containing 0.5 M sulfuric acid and 0.1 M formic acid. The linear sweep voltammetry, cyclic voltammetry, and chronoamperometry techniques were also employed to evaluate the electrocatalytic activity of prepared samples toward the oxidation of formic acid. In this respect, the influence of some factors such as formic acid and sulfuric acid concentrations and also potential scan rate was investigated. Compared to the pure Pd sample, the Pd–Cd samples were more reactive for the oxidation of formic acid. Besides, the sample with a lower amount of Pd (Pd_1·3Cd) demonstrated much higher electrocatalytic activity than the Pd_7·1Cd and Pd_2·1Cd samples. The observed high mass activity of 15.06 A mg^?1_Pd for the Pd_1·3Cd sample which is 21.1 times higher than Pd/C is an interesting result of this study.     

水泥浆失水制约下套管与井眼间隙的研究

通过对水泥浆失水规律的室内试验分析以厦对注水泥顶替过程中水泥浆失水桥堵套管与井眼间隙问题的研究，建立了顶替过程中滤失层不发生水泥浆失水而桥堵环形空间的临界失水量计算模型，提出了调配水泥浆失水性能和确定合理套管井眼间隙的具体方法，对注水泥现场施工和井身结构设计具有一定的指导意义。