高压脉冲放电处理含氰废水的影响因素探讨

焦化废水中含有大量的氰化物,必须采取有效措施进行去除,传统去除方法运行成本高、操作复杂。提出了用高压毫微秒脉冲产生的非平衡等离子体处理含氰废水的方法,对其影响因素pH值、放电时间、气流量、放电条件等进行了大量的实验研究,结果表明:溶液初始pH值为9.09,放电2 h,放电电压46 kV时氰化物的去除率最高可达93.2%,氰化物质量浓度可降至0.26 mg/L。实验对比了放电与不放电氰化物的去除效果:相同条件下放电后氰化物的去除率大大提高,为焦化废水中氰化物的去除提出了一种新的方法。     

Gasification of polyethylene using steam plasma generated by microwave discharge

Gasification of polyethylene (PE) pellet was studied using atmospheric argon-steam plasma generated by microwave discharge and the feasibility of the process was examined. The experimental results showed that additional steam to argon plasma promoted the weight decrease of PE and enhanced the production of H₂, CO, CO₂ and CH₄. The results confirmed that the treatment of plastics with the steam plasma was effective to obtain synthesis gas.     

克拉-2气田射孔工艺研究

克拉-2气田具有5大射孔难题:射孔井段长、地层压力大、产气量大、流体中腐蚀性物质和不宜丢枪,作业风险非常大。提出了带枪生产的射孔方案和射孔后取枪生产2种射孔方案,通过分析对比优选出最佳方案——最终选定模块式射孔枪过油管方案,并对该方案作了较为详尽的叙述,在后来的施工中成功地得到了印证。     

Time Characterization of High Density Gas Jet from a Pulsed Supersonic Nozzle via Laser Produced Plasma

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10μs with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 10^19 cm^-3, compared with theoretical simulations from the nozzle parameters.     

美国危险废物处理的领先尖端技术--等离子强化熔炉介绍

从工作原理、主体结构、工艺流程等方面，系统地介绍了当代处理危险废弃物的领先尖端技术——等离子强化熔炉，并结合实地考察，介绍了其工业化发展及其应用实例。     

一种基于bit位的运动补偿方法

本文讨论了等离子体显示屏所特有的在显示运动画面时出现的伪轮廓线现象，对产生的原因进行了分析并给出了软件模拟的结果。在此基础上，提出了一种基于bit位的运动补偿方法来改善运动图像的画面质量，同时根据人眼的视觉特征对补偿方法做了进一步的优化。最后对基于bit位的运动补偿方法进行了比较和验证，结果表明基于bit位的运动补偿方法可以基本消除运动画面的伪轮廓线现象。     

The Structure of Clusters and Jets of Pulsed Plasma Expanding into Vacuum

The space-time distribution of the basic kinetic parameters of a plasma is experimentally determined under conditions of expansion of plasma clusters and jets into vacuum. It is demonstrated that the dynamics and structure of plasmoids injected by pulsed erosion plasma accelerators of the electrothermal type are characterized by two successive stages or two modes of acceleration, namely, the Joule heating of electrons in the initial region of the path and the collisionless expansion of rarefied plasma.     

氧气顶吹转炉溅渣护炉试验研究

采用水力模型研究方法 ,针对马钢 2 0t转炉进行溅渣护炉冷态模拟试验 ,得出最佳工艺参数为 :枪位 1680mm ,氮气流量为 110 0 0m3/h ,大流渣量 ,渣粘度适中。此外 ,在满足炼钢生产的条件下 ,采用夹角为 13°的喷头溅渣效果好     

Plasma Sprayed Hydroxyapatite Coatings with Nano-hydroxyapatite Prepared by Ultrasonic Precipitation Process

Nano-particle hydroxyapatite （ HA ） was prepared with a novel ultrasonic precipitation process and the as-prepared nanopowder was used to produce hydroxyapatite （ HA ） coatings on titanium substrate via plasma spraying. The phase and the microstructare of the coating were characterized by X- ray diffraction （XRD） and scanning electron microscopy （SEM）. Results showed that spherical particles could be prepared by ultrasonic precipitation process; and a corresponding dense HA coating with molten surface and low-porosity cross-section structure was acquired. During the plasma spraying process, new phases of Ca3 （ PO4 ）2 and Ca2 P2O7 were generated. After heat-treating at 800℃ for 1 h, the contents of Ca3 （ PO4 ）2 and Ca2 P2O7 decreased while HA content increased. Tensile adhesion tests showed that the plasma sprayed coating prepared with the spherical nanoparticles exhibited high tensile bond strength.     

高效率平面磁控溅射器的研制

介绍一种新型磁控溅射装置。它采用两块极性相对的环状磁铁的设计方法，通过扩大靶表面的等离子放电区域面积，使传统磁控溅射枪使用中经常受到的两个限制──溅射速率与靶的利用率得到了较大的改善。实验中铜靶在溅射功率密度为11W／cm~2时溅射速率约为800nm／min，如果继续提高功率则可获得更高的速率。而靶的利用率可达64％左右。另外，在认为出射粒子符合cos~nθ分布的前提下，发现当n＝3．3时，实验数据和理论数据符合得较好。