面源红外诱饵对抗红外制导导弹干扰策略研究

面源红外诱饵使用的过程中,合理有效的干扰策略是干扰红外制导导弹的关键,针对这一问题,通过理论分析与仿真模拟相结合得到面源红外诱饵对抗红外制导导弹的干扰策略。首先以红外成像制导导弹为例,介绍红外制导导弹的仿真模型,然后将攻击过程分为锁定前与锁定后,以命中率为评价指标,得到两个阶段下的最佳干扰策略,包括诱饵的最佳释放时机、释放间隔以及载机应采取的机动动作等。     

红外光谱法用于快速测定车用柴油酸度等性质的研究

针对车用柴油酸度等性质测定过程繁琐，采用衰减全反射样品池测定车用柴油的红外光谱，用偏最小二乘法（PLS）建立红外光谱测定车用柴油酸度、密度、闪点和凝点的4个校正模型，验证标准误差分别为0.46 mg/(100 mL),0.77kg/m3,2.60 ℃,2.77 ℃，该方法符合标准方法再现性要求。与标准方法相比，该方法具有无需预处理、操作简单、测量快速、重复性好等优点。     

反铁磁晶体的红外频率特性

研究了红外频段非线性s偏振表面波在反铁磁晶体和电介质交界面上的频率特性，求出了非线性色散方程，揭示了非线性s偏振表面波存在一个临界频率，低于这个频率，非线性s偏振表面波的频率范围，发现功率不再是决定导波频率范围的唯一因素，两种材料的介电常数比在这里起了至关重要的作用。     

Preparation, Characterisation and Catalytic Behaviour of a New TeVMoO Crystalline Phase

TeM_xMo_1.7O mixed oxides (M = V and/or Nb; x = 0-1.7) have been prepared by calcination of the corresponding salts at 600 °C in an atmosphere of N₂. A new crystalline phase, with a Te/V/Mo atomic ratio of 1/0.2-1.5/1.7, has been isolated and characterised by XRD and IR spectroscopy. This phase is observed in the TeVMo or TeVNbMo mixed oxide but not in the TeNbMo mixed oxide. The new crystalline phase shows an XRD pattern similar to Sb₄Mo₁₀O₃₁ and probably corresponds to the M1 phase recently proposed by Aouine et al. (Chem. Commun. 1180, 2001) to be present in the active and selective MoVTeNbO catalysts. Although these catalysts present a very low activity in the propane oxidation, they are active and selective in the oxidation of propene to acrolein and/or acrylic acid. However, the product distribution depends on the catalyst composition. Acrolein or acrylic acid can be selectively obtained from propene on Nb-free or Nb-containing TeVMo catalysts, respectively. The presence of both V and Nb, in addition to Mo and Te, appears to be important in the formation of acrylic acid from propene.     

通用串行总线原理及其外设接口设计

以通用串行总线(USB)1.1为基础,讨论了USB的体系结构、工作原理、通信协议和相应的核心技术,并介绍了一种基于USB接口的数字摄像系统的设计方案及其软件、固件的设计.     

An investigation into physicochemical characteristics of ash produced from combustion of oil palm biomass wastein a boiler

Ash derived from combustion of Malaysian oil palm biomass (empty fruit bunches consisting of fibers) was physically and chemically characterized in order to provide a comprehensive understanding of its specific properties in terms of toxicity, compositions and reusability. Principal analyses conducted include particle size distribution, scanning electron microscopy, elemental dispersive X-ray, elemental analysis, toxicity characteristic leaching procedure (TCLP) as well as thermogravimetric, X-ray diffractometry and Fourier-transform infrared analyses. TCLP result indicated that the oil palm ash (OPA) should not be classified as toxic wastes in terms of heavy metal leachability since leachable copper, cadmium, lead and nickel concentrations were detected below the stipulated leachability limits. It was determined that the OPA contained high amount of potassium as well as presence of silica which implied its suitability to be reused as crude fertilizer or cement replacement material.     

用红外热象技术研究有凸台热源倾斜板的散热

本文介绍红外热象技术在工程热物理研究中某些应用的探索。作为实例，通过热象技术，实验研究了具有水平凸台离散热源的倾斜板的散热，在研究它的自然对流换热部份结合利用激光全息干涉技术。此间着重于分析倾斜角对散热的影响。     

Hybrid gas-to-particle conversion and chemical vapor deposition for the production of porous alumina films

Porous alumina films can be found in a wide variety of materials, including filters, thermal insulation components, dielectrics, biomedical and catalyst supports, coatings and adsorbents. Production methods for these films are as equally diverse as their applications. In this work, a hybrid process based upon chemical vapor deposition and gas-to-particle conversion is presented as an alternative technique for producing porous alumina films, with the main advantages of solvent-free, low substrate-temperature operation. In this process, nanoparticles were produced in the vapor phase by reaction of aluminum acetylacetonate in the presence of oxygen. Downstream of this reaction zone, these nanoparticles were collected via thermophoresis onto a cooled substrate, forming a porous film. Some deposited films were subjected to post-processing in the form of annealing in air. Fourier-transform infrared spectra and X-ray energy-dispersive spectroscopy analysis confirmed the production of alumina at processing temperatures above 973 K. X-Ray diffraction revealed that the films were amorphous. Film thickness, ranging from 30 to 250 μm, and the average deposition rate were determined from scanning electron microscopy results. From transmission electron microscopy, the average primary particle size was determined to be approximately 18 nm and the formation of nanoparticle aggregates was evident. Annealing of the films at temperatures ranging from 523 to 1173 K in the presence of air did not have an effect on particle size. The specific surface area of the powder composing the films ranged from 10 to 185 m² g⁻¹, as determined from nitrogen gas adsorption by the Brunauer–Emmett–Teller method.     

Determining stress intensity factors of composites using crack opening displacement

The main purpose of this paper is to find the mixed-mode stress intensity factors of composite materials using the crack opening displacement (COD). First, a series solution of the composite material with a crack was used to evaluate COD values. Then, the least-squares method was used to calculate mixed-mode stress intensity factors. This algorithm can be applied to any method that generates or measures COD values. The major advantage of this method is that COD values very near the crack tip are not necessary. Both finite element simulations and laboratory experiments were applied to validate this least-squares method with acceptable accuracy if the even terms of the series solution are removed.