Present status and future prospects of PV activities in Japan

The photovoltaic (PV) power systems in Japan made great strides in the past decade. The PV industry in the 1990s greatly depended on the research projects and dissemination programs carried out by the Ministry of International Trade and Industry. However, the industrial structure for full-scale deployment of the PV system is currently being established by the manufacturers’ continuous efforts to reduce the PV system cost and the government’s consecutive supports to create the initial market. It is expected that the synergetic effect of the cost reduction and incentives for introduction will activate the PV industry and its market more and more toward achieving 5000 MW of the capacity in FY 2010.     

真空碳热还原法制备高密度碳化钒

研究了采用真空碳热还原法由三氧化二钒制备碳化钒，并研究了碳化钒产物密度随实验条件的变化规律。找到了用于强化碳化钒产物密度的添加剂，研究结果表明，反应温度，添加剂是影响碳化钒产物密度的主要因素。反应时间对产物密度也有一定影响。研究结果同时表明，含铁化合物能有效地提高产物密度。     

静载荷和疲劳载荷作用下 C/Al 正交层压板的力学响应

本文讨论静载荷及疲劳载荷作用下 C/Al 正交层压板的力学响应,并考虑损伤过程中的临界现象,以此作为结构设计准则的基础。对静载荷作用的情况:(1)90°铺层的门槛应变ε_(FPF)随着约束程度增加而增加,而且开裂后的行为也受约束程度的影响。(2)经历加载-卸载再重新加载至断裂的过程后,初始试样存在一个剩余永久变形,其损伤状态可以用刚度的变化来表征;而疲劳试样在加载-卸载过程中刚度变化很小,反映其损伤达到一个稳定的状态。对疲劳载荷作用的情况:(1)对于给定的应力比 R,试样会趋于与它所承受的 S_(max)最大值相应的 SDS 状态。循环应力范围的不断增大,会引起基体损伤的增加,从而重新建立新的饱和损伤状态。(2)对于每一损伤状态均有一对应的循环应变范围 Δε。在 SDS 状态下,Δε保持不变。(3)以刚度下降为损伤参数对 C/Al 层压板进行了降级应力分析,并由此来预计在ΔS_(sh)以下,层压板不会发生疲劳损伤累积。     

高阶系统次优控制集结设计方法

针对现有集结降阶方法计算量大，或者不能保证精确集结，本文给出一种新的精确集结降阶算法，提出一种基于精确集结模型，设计高阶系统的低阶次优线性调节器和集结状态降维观测器的方法。     

坦克红外特征控制技术评述

坦克红外特征控制对于提高坦克的战场生存能力具有重要意义。控制的主要方法有遮障、表面处理、外形技术、主动冷却、总体设计等。坦克红外特征的控制必须与其他波段，特别是射频波段的特性控制兼容。遮障和低发射率涂料是现役坦克红外特征控制的主要措施。而对未来的主战坦克，设计应是减少其系统特性的重要途径。     

Optically tuned superconductive-dielectric resonators with whispering-gallery modes

An analytical method is presented for calculating the resonant frequency andQ-factor of a superconducting dielectric disk resonator operating in millimeter-wave regime with whispering-gallery mode. Resonant frequency shift due to the optical generation of quasi-particles in superconducting film is investigated as a function of photon flux. An optically tunable resonant frequency of about 500 MHz is estimated, and good agreement is found between numerical results and experimental ones.     

2—叠氮—1萘醌—5—磺酸生产工艺优化

研究以L-酸为原料,对合成用于制作PS版的2-叠氮1-萘醌-5-磺酸的亚硝化、还原及重氮化三步生产工艺进行最佳配比选优试验。结果表明对L-酸的总收率可达73-75％.获得了较高的收率。     

葡萄糖电解氧化还原工艺研究

采用自制的无膜电解槽，对同时电解氧化还原葡萄糖生成葡萄糖酸和山梨醇的工艺进行了研究。所得到的最佳工艺条件为：葡萄糖浓度０．４ｍｏｌ／Ｌ，ｐＨ值１１，电流密度３Ａ／ｄｍ￣２。在此条件下电解１２ｈ，葡萄糖转化率可达９６．４％，葡萄糖酸产率８８％，山梨醇产率１０％。同时，考察了和Ｚｎ￣（２＋）加入以及ｐＨ值对电流效率的影响。     

尼龙6表面金属(Ni)化膜材料的制备及性能研究

用化学还原法制得了尼龙６表面金属（Ｎｉ）化膜材料。研究了还原条件，金属盐浓度对膜材料电性能的影响，以及膜材料的电发热性能，用光电子能谱和扫描电子显微镜对其表面及形貌进行了表征。     

Nitrogen dioxide effect in the reduction of nitric oxide by propane in oxidizing atmosphere

The role of nitrogen dioxide in the selective reduction of NO by propane over a Cu-MFI zeolite is investigated. NO₂ and NO reductions were carried out under similar conditions of reaction. In the presence of oxygen, the reduction of NO by C₃H₈ does not differ significantly from that of NO₂. In the absence of oxygen, the reduction of NO₂ by propane occurs with a partial decomposition of the nitric dioxide molecule. Such a decomposition leads to the formation of oxygen, which is responsible for the increase in catalytic activity by comparison with the same reaction performed with NO. NO₂ formed and released in the gas phase during the reduction of NO by propane in the presence of oxygen does not play a predominant role in the catalytic process.