ERD facility for analysis of hydrogen and deuterium in solids

Hydrogen is the lightest element in nature, and so, its detection and quantitative analysis is difficult by the conventional methods utilized for other elements. In the recent years the technique of elastic recoil detection analysis (ERD) using 1–2 MeV He⁺ beam has been developed to quantitatively and simultaneously analyze hydrogen and its isotopes in solids. Such a facility has been set up using the 2 MeV Van-de-Graaff accelerator at IIT Kanpur. It facilitates H and D analysis in a material up to a depth of ∼ 1μm with a detection sensitivity of 0·1 at.% and depth resolution of about 300 ?. The application potential of this setup is illustrated by presenting the results of measurements performed on Al:H:D systems prepared by plasma source ion implantation and highT _c YBCO pellets exposed to humid atmosphere.     

A Study of the Specific Heats of the Compounds in the Sm_2O_3-BaO-CuO System

By means of X-ray diffraction and adiabatic scanning calorimeter,the specific heatsof five compounds in the Sm_2O_3-BaO--CuO system,such as Sm_2BaO_4,Sm_2CuO_4,BaCuO_4,Sm_2BaCuO_5,SmBa_2Cu_3O_(7-x),from -150℃ to 800℃ have been measured.It is found that the specific heats ofthese compounds increase smoothly with the increase of temperature.     

Development of Solar Drying

Importance of Solar Drying is increasing worldwide, especially in areas where the use of the abundant, renewable and clean solar energy is essentially advantageous. In the developing countries and in rural areas the traditional open-air drying methods should be substituted by the more effective and more economic solar drying technologies.

R&D needs should be considered in the basic research and experimental fields; in performance measurement; in the modelling-simulation-design and testing. The international co-operation of experts should be improved and more efforts would be needed in the policy and in the public information.     

武钢“八五”技术进步的新起点

本文论述了武钢新三号高炉的建设和投产,是武钢整个“八五”技术进步的新起点,指出必须进一步完善以质量为核心的生产管理体系。     

Evolution of BET internal surface area in glassy carbon powder during thermal oxidation

It is demonstrated that glassy carbon powder can be thermochemically activated. During activation, a film with open pores is created on the glassy carbon particles. This film has a large internal surface area, which is accessible to liquids and gases. A simple model for the evolution of the internal surface area in glassy carbon powder during thermochemical gas-phase oxidation is also presented and compared with experimental data. Experimental results are in qualitative agreement with the model. We found that a sharp particle size distribution is desirable with regard to potential technical applications.     

数据融合在C^3I系统中的应用

多传感器数据融合技术已在军事领域受到广泛重视，并逐步走向实际应用，本文简要介绍它的一般组成、特点以及在军事Ｃ＾３Ｉ系统应用中的主要功效。     

Immobilization of an endopectinlyase on γ-alumina: Study of factors influencing the biocatalytic matrix stability

Endopectinlyase (EC 4.2.2.10) from Aspergillus japonicus was immobilized on to γ-alumina. Adsorption performed at pH 5·0 and a subsequent cross-linking phase using 0·1% glutaraldehyde were the chosen immobilization conditions. The comparison between the main biochemical parameters of the immobilized and free form of the enzyme showed that the immobilization procedure used did not affect the enzyme biochemical properties. The interactions between the carrier and the enzyme are essentially secondary bonding. In fact they depend on the pH and on the presence of phosphate ions in the medium. A tentative chemical model of the biocatalytic matrix thus obtained is proposed.     

三辊穿孔和轧管所产生的钢管壁厚极差和波浪形内螺纹

定量描述了实际生产过程中三辊斜轧穿孔所产生的钢管壁厚极差和波浪形内螺纹，初步探讨了三辊轧管机对钢管壁厚极差和波浪形内螺纹的影响。     

Three‐dimensionally braided carbon fiber–epoxy composites,a new type of material for osteosynthesis devices. I. Mechanical properties and moisture absorption behavior

In recent years, three‐dimensionally (3D) braided composites have attracted a great deal of attention because of their high‐impact damage tolerance and fatigue life, superior fracture toughness, and so forth, and have been used in aeronautics, military, and transportation. These advantages make them strong candidates for osteosynthesis devices. In this study, 3D braided carbon fiber–epoxy (C_3D/EP) composites were produced via a simple vacuum impregnation technique. The load‐deflection curve, mechanical properties, and influence of fiber volume fraction, braiding angle, and axial reinforcing fibers were examined to determine their suitability for internal fixation devices. It is found that the C_3D/EP composites have excellent toughness and do not show brittleness when fractured because of their relatively high void content. The flexural, shear, and impact strengths of the C_3D/EP composites are excellent. It was shown that a C_3D/EP composite with a stiffness similar to load‐bearing bones can be made while maintaining enough strength. It is concluded that a relatively higher void content and braiding angle is more suitable for the C_3D/EP composites from the viewpoint of requirements of fracture fixation materials. The moisture absorption behavior and changes in mechanical properties caused by moisture uptake were evaluated. Results show that absorbed moisture slightly decreases mechanical properties of the C_3D/EP composites. Contrary to the unreinforced epoxy, the moisture absorption behavior of the C_3D/EP composites cannot be described with Fick's law of diffusion, probably because of the presence of voids and/or 3D fiber structure. The exact mechanisms should be proposed in further investigations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1031–1039, 2002     

Analysis of characteristic odors from human male axillae

A number of studies concerning the analysis of axillary odors have assumed that the characteristic odor produced in the axillae is due to volatile steroids and isovaleric acid. Organoleptic evaluation of Chromatographic eluants from axillary extracts was employed to isolate the region in the chromatogram where the characteristic odor eluted. The odor of the dissolved eluant was eliminated when it was treated with base, suggesting that acids make up the characteristic axillary odor. Subsequent extraction of the pH-adjusted axillary extract in conjunction with organoleptic evaluation of the Chromatographic eluant, preparative gas chromatography, and analysis by GC-MS as well as GC-FTIR showed the presence of a number of C₆ to C₁₁ straight-chain, branched, and unsaturated acids as important contributors to the axillary odor. The major odor component is (E)-3-methyl-2-hexenoic acid. Three homologous series of minor components are also important odor contributors; these consist of the terminally unsaturated acids, the 2-methyl-C₆ to -C₁₀ acids and the 4-ethyl-C₅ to -C₁₁ acids. These types of acids have not been reported previously as components of the human axillary secretions and have not been proposed previously as part of the principal odor components in this area.