Phase composition and properties of solid solutions of GdFeO3–GdInO3 bulks

Solid solutions of the GdFeO₃–GdInO₃ system were prepared at 1550 °C by ceramic powder processing. The formulated composition was Gd(Fe_1−xIn_x)O₃ (GFI) with the indium contents at x = 0, 0.25, 0.5, 0.75, and 1.0. A stable phase of Gd(Fe_1/3In_2/3)O₃ in our system was identified by X-ray diffraction and phase composition analysis. Multi-phase morphologies were observed for GFI bulks with x = 0.5 and 0.75. Dielectric and electrical properties of the GFI bulks were investigated. The addition of 25% In³⁺ in GdFeO₃ had an obvious enhancement in polarization and led to an elevated resonance frequency. Dielectric properties of GFI bulks except GdInO₃ were strongly dependent upon the test frequency, which corresponded to the response of polarization mechanism. GdInO₃ displayed as a stable dielectric, which was frequency- and temperature-insensitive. GdInO₃ was thermally activated and became leaky until above 600 °C.     

Photocatalytic degradation of 2,2‐bis(4‐hydroxy‐3‐methylphenyl) propane (BPP) based on molecular recognition interaction

BACKGROUND: Endocrine disruptors in the aquatic environment and their potential adverse effects are currently issues of concern. One of these endocrine disruptors is 2,2‐bis(4‐hydroxy‐3‐methylphenyl)propane (BPP). In this work the molecular recognition interaction of BPP with β‐cyclodextrin (β‐CD) was studied using IR spectroscopy and steady state fluorescence spectroscopy, and the photocatalytic degradation behaviour of BPP based on molecular recognition interaction was investigated in a TiO₂/UV–visible (λ_max = 365 nm) system. This might provide a new method for the treatment of some organic pollutants in wastewater. RESULTS: β‐CD reacts with BPP to form a 1:1 inclusion complex, the formation constant of which is 4.94 × 10³ L mol^?1. The photodegradation rate constant of BPP after molecular recognition by β‐CD showed a 1.42‐fold increase in the TiO₂/UV–visible (λ_max = 365 nm) system. The photodegradation of BPP depended on the concentration of β‐CD, the pH value, the gaseous medium and the initial concentration of BPP. The photodegradation efficiency of BPP with molecular recognition was higher than that without molecular recognition. After 100 min of irradiation the mineralisation efficiency of BPP after molecular recognition by β‐CD reached 94.8%, whereas the mineralisation efficiency of BPP before molecular recognition by β‐CD was only 40.6%. CONCLUSION: The photocatalytic degradation of BPP after molecular recognition by β‐CD can be enhanced in the TiO₂/UV‐visible (λ_max = 365 nm) system. This enhancement is dependent on the enhancement of the adsorption of BPP, the moderate inclusion depth of BPP in the β‐CD cavity and the increase in the frontier electron density of BPP after molecular recognition. Copyright © 2008 Society of Chemical Industry     

One‐step production of 2,3‐butanediol from starch by secretory over‐expression of amylase in Klebsiella pneumoniae

BACKGROUND: 2,3‐Butanediol (2,3‐BD) is a valuable chemical that can be biosynthesized from many kinds of substrates. For commercial biological production of 2,3‐BD, it is desirable to use cheap substrate without pretreatment, such as starch. However, there have been few reports on the production of 2,3‐BD directly from starch. RESULTS: In this work, gene malS coding for α‐amylase (EC 3.2.1.1) precursor was inserted into plasmid pUC18K, and secretory over‐expression of α‐amylase was achieved by engineered Klebsiella pneumoniae. The extracellular recombinant amylase accelerated the hydrolyzation of starch, and one‐step production of 2,3‐BD from starch was carried out by engineered K. pneumoniae. A 2,3‐BD concentration of 3.8 g L^?1 and yield of 0.19 g 2,3‐BD g^?1 starch were obtained after 24 h fermentation. CONCLUSION: The one‐step production of 2,3‐BD from starch was achieved by secretory over‐expression of amylase in K. pneumoniae. This would simplify the process and reduce the production cost considerably by enabling use of starch with minimal pretreatment. Copyright © 2008 Society of Chemical Industry     

Material removal and surface damage in EDM of Ti3SiC2 ceramic

Material removal and surface damage of Ti₃SiC₂ ceramic during electrical discharge machining (EDM) were investigated. Melting and decomposition were found to be the main material removal mechanisms during the machining process. Material removal rate was enhanced acceleratively with increasing discharge current, i_e, working voltage, u_i, but increased deceleratively with pulse duration, t_e. Microcracks in the surface and loose grains in the subsurface resulted from thermal shock were confirmed, and the surface damage in Ti₃SiC₂ ceramic led to a degradation of both strength and reliability.     

3ds Max和Photoshop在水利工程中的结合应用

通过在水利行业中对3dsMax和Photoshop使用,总结出5个针对水利工程中3dsMax和Photoshop结合使用的一些方法,为水利工程申报和水利建设汇报提供一些参考方法.     

Kinetics study of Ti[O(CH2)4OCHCH2]4 initiated ring‐opening polymerization of ε‐caprolactone by differential scanning calorimetry

Chemical shrinkage was used for the in situ measurement of the progressing chemical stabilization reactions and the influence of ozone during the stabilization of polyacrylonitrile. A method for evaluating the activation energy through the sensitivity temperature is presented. The calculated results show that the activation energies were 161.57 kJ/mol in air and 181.23 kJ/mol in ozone-enriched air. Therefore, the chemical reactions were postponed during stabilization in ozone-enriched air. Ozone seemed to act in three ways: first, ozone promoted the formation of the serious skin–core structure. Second, ozone accelerated the chemical reactions and shortened the stabilization time at lower heating rates. Third, ozone postponed the chemical reactions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Maghnite‐H+, a solid catalyst for the cationic polymerization of α‐methylstyrene

The polymerization of α‐methylstyrene (AMS) catalyzed by Maghnite‐H⁺ (Mag‐H) was investigated. Mag‐H is a montmorillonite sheet silicate clay, exchanged with protons. It was found that the cationic polymerization of AMS is initiated by Mag‐H at ambient temperature in bulk and in solution. The effect of the amount of Mag‐H, the temperature, and the solvent was studied. The polymerization rate increased with increase in the temperature and the proportion of catalyst, and it was larger in nonpolar solvents. These results indicated the cationic nature of the polymerization. It may be suggested that the polymerization is initiated by proton addition to monomer from Mag‐H. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Coincidence Doppler broadening spectroscopy in polyvinyl chloride after doping with Al2O3

Coincidence Doppler broadening of annihilation radiation (CDBAR) and Vickers hardness techniques were performed to study pure Al₂O₃, pure polyvinyl chloride (PVC), and doped PVC with different concentrations of Al₂O₃ (10–50%). The CDBAR ratio curves with respect to pure PVC were presented and reflect the momentum distribution of all the samples. The peak around 14.5 ×10^?3 m_oC in the CDBAR ratio curves suggests a large contribution of positron annihilation with the Al₂O₃. There is a linear correlation between the height of this peak and the Al₂O₃ concentration. The S‐ and W‐parameters were extracted from the CDBAR spectra and increase with increasing the Al₂O₃ concentration showing discontinuity at 30% of Al₂O₃ concentration on PVC. The present data confirmed that there is no positronium formation in pure Al₂O₃ as a result of smaller S‐parameter. The Vickers hardness increases with increasing the Al₂O₃ concentration in PVC showing a linear dependence with two different slopes depend on the Al₂O₃ concentration range. A correlation between the Vickers hardness (macroscopic data) and the W‐parameter (microscopic data) was observed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Scaling laws and internal structure for characterizing electrospun poly[(R)-3-hydroxybutyrate] fibers

Using chloroform/dimethylformamide (CF/DMF) co-solvent, electrospinning of poly[(R)-3-hydroxybutyrate] (PHB) solutions was carried out at ambient temperature. The effects of the applied voltage (V), flow-rate (Q), and solution viscoelastic properties on the Taylor cone, electrified jet, and fiber morphology were investigated. In addition, the electric field developed by the needle-plate electrode configuration was calculated using a finite element analysis to reveal the tip-to-collector (H) effect. Among the processing parameters (V, Q and H), it was found that Q played a key role in determining the jet diameter (d_j) and electrospun fiber diameter (d_f), and scaling laws existed between them, i.e., d_j-Q^0.61 and d_f-Q^0.33. The diameter reduction ratios of D_o/d_j (D_o is the needle diameter) and d_j/d_f were measured as 50-120 and 5-10, respectively; it suggested that major jet stretching took place in the straight electrified jet region, and further chain orientation could be gained by the subsequent process of jet whipping. By changing PHB concentrations from 5 to 15 wt%, the solution viscosity (η_o) was increased from 100 to 4900 cP, whereas the surface tension and solution conductivity remained unchanged; it provided a good model solution to exclusively reveal the η_o effect on the electrospinning process. Our results showed that the η_o-dependence of d_j and d_f also followed simple scaling laws: d_j-η_o^0.06, and d_f-η_o^0.39, with a prefactor depending on the processing variables, mainly the flow-rate. Regardless of the PHB concentrations used, the obtained PHB fibers showed a similar crystallinity fraction of ca. 0.63 and possession of major α-crystals together with a small amount of β-crystals with zigzag chain conformation.     

Towards a new definition of EPOC parameters for anionic electrochemical catalysts: case of propene combustion

The electrochemical promotion of catalysis (EPOC) of propene combustion was investigated using Pt sputtered thin film on an O²⁻ conductor, 8 mol% Y₂O₃-stabilized-ZrO₂ (YSZ). In order to separate the influence of the thermal migration of the O²⁻ oxide ions from the electrolyte to the catalyst surface and the impact of an electrical polarization on the catalytic activity, several light-off experiments (cool down and heat up procedures) were successively performed under different polarizations, i.e. OCV, +2 and −2 V. These experiments have clearly shown that the presence of O²⁻ (thermally or electrochemically induced) inhibits the catalytic activity of the platinum for the propene deep oxidation. These results demonstrate the importance to define a normalized rate enhancement ratio, ρ _n , from a reference value of the catalytic rate corresponding to a Pt surface state free of O²⁻ ions.